Industrial Wall-mount Managed Gigabit Ethernet Switch WGS-804HPT/WGS-4215-8T/WGS-4215-8T2S Quick Installation Guide
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 4 3. Wiring the Power Inputs............................................................................... 5 3.1 Terminal Block Connector Pinout............................................................ 6 4. Installation..................................................
1. Package Contents Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch, WGS-804HPT / WGS-4215-8T / WGS-4215-8T2S. The table below shows the models with the number of ports: Model Name 10/100/1000T Copper Ports 802.
2. Requirements zz Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Ethernet Port Connection Network cables -- Use standard network (UTP) cables with RJ45 connectors. The above PC is installed with Web browser and JAVA runtime environment plug-in. Note 4 It is recommended to use Internet Explore 8.
3. Wiring the Power Inputs The Wall-mount Managed Switch features a strong dual power input system (Terminal block and DC jack) incorporated into customer’s automation network to enhance system reliability and uptime.
3.1 Terminal Block Connector Pinout To install the 3-pin Terminal Block Connector on the Wall-mount Managed Switch, simply follow the following steps: Step 1: Insert positive DC power wire into V+, negative DC power wire into V-, and grounding wire into Ground. Ground VV+ Step 2: Tighten the wire-clamp screws for preventing the wires from loosening and plug into the Wall-mount Managed switch. Note 6 1. The wire gauge should be in the range from 12 to 24 AWG. 2. The device must be grounded.
4. Installation 4.1 Wall Mount Installation To install the Wall-mount Managed Switch on the wall, simply follow the following steps: Step 1: There are 4 holes with 8mm diameter on the wall; the distance between the 2 holes is 133mm(WGS-804HPT/WGS-4215-8T), 163mm(WGS-42158T2S) and the line through them must be horizontal. Step 2: Install a conductor pipe inside the board hole and flush the edge of the conductor pipe with the wall surface. Step 3: Screw the bolts into the conductor pipe.
4.2 Magnet Installation To install the Wall-mount Managed Switch on a magnetic surface, simply follow the following diagram: 4.3 DIN-rail Mount Installation The DIN-rail kit is included in the package. When the wall-mount application for the Wall-mount Managed Switch needs to be replaced with DIN-rail application, please refer to the following figures to screw the DIN-rail on the Wall-mount Managed Switch.
Step 2: Lightly insert the button of DIN-rail into the track 1 Push 2 Click Step 3: Check whether the DIN-rail is tightly on the track 9
5. Starting Web Management The following shows how to start up the Web Management of the Wall-mount Managed Switch. Note the Wall-mount Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Wall-mount Managed Switch is 192.168.0.100; then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100) and the default subnet mask is 255.255.255.0.
Logging in to the Wall-mount Managed Switch 1. Use Internet Explorer 8.0 or above Web browser and enter IP address http://192.168.0.100 to access the Web interface. 2. When the following dialog box appears, please enter “admin” in both the default user name and password fields. The login screen in Figure 5-2 appears. Default Username: admin Default Password: admin Figure 5-2: Web Login Screen 3. After entering the password, the main screen appears as Figure 5-3 shows.
Figure 5-3: Web Main Screen of Wall-mount Managed Switch The Switch Menu on the left of the Web page lets you access all the commands and statistics the Wall-mount Managed Switch provides. Figure 5-4: Switch Menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more.
6. Saving Configuration via the Web In the Wall-mount Managed Switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence of runningconfig can be saved from the RAM to FLASH by “Save Configurations to FLASH” function, so that the running configuration sequence becomes the startup configuration file, which is called configuration save.
7. Recovering Back to Default Configuration IP Address has been changed or admin password has been forgotten – To reset the IP address to the default IP Address “192.168.0.100” or reset the login password to default value, press the reset button on the front panel for about 5 seconds. After the device is rebooted, you can login the Web interface management within the same subnet of 192.168.0.xx.
8. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ: http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address: support_switch@planet.com.tw WGS-804HPT / WGS-4215-8T / WGS-4215-8T2S User’s Manual: http://www.planet.com.tw/en/support/download.
