Industrial Wall-mount Managed Gigabit Ethernet Switch WGS-804HPT WGS-4215-8T/WGS-4215-8T2S/WGS-4215-8P2S WGS-4215-16P2S Quick Installation Guide
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 4 3. Wiring the Power Inputs............................................................................... 5 3.1 Terminal Block Connector Pinout............................................................ 6 3.2 DC Power Jack................................................
1. Package Contents Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch, WGS-804HPT and WGS-4215 series. The table below shows the models with the number of ports: Model Name 10/100/1000T Copper Ports 802.
2. Requirements zz Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Ethernet Port Connection Network cables -- Use standard network (UTP) cables with RJ45 connectors. The above PC is installed with Web browser and JAVA runtime environment plug-in. Note 4 It is recommended to use Internet Explorer 8.
3. Wiring the Power Inputs The Wall-mount Managed Switch features a strong dual power input system (terminal block and DC jack) incorporated into customer’s automation network to enhance system reliability and uptime.
3.1 Terminal Block Connector Pinout To install the 3-pin Terminal Block Connector on the Wall-mount Managed Switch, simply follow the following steps: Step 1: Insert positive DC power wire into V+, negative DC power wire into V-, and grounding wire into Ground. Ground VV+ Step 2: Tighten the wire-clamp screws for preventing the wires from loosening and plug into the Wall-mount Managed switch. Note 1. The wire gauge should be in the range from 12 to 24 AWG. 2. The device must be grounded. 3.
4. Hardware Installation 4.1 Wall Mount Installation To install the Wall-mount Managed Switch on the wall, simply follow the following steps: Step 1: It is required 4 holes with 8mm diameter on the wall; the distance between the 2 holes is 133mm (WGS-804HPT/WGS-4215-8T), 163mm (WGS-4215-8T2S/WGS-4215-8P2S), 230 mm (WGS-4215-16P2S) and the line through them must be horizontal. Step 2: Install a conductor pipe inside the board hole and flush the edge of the conductor pipe with the wall surface.
4.2 Magnet Installation To install the Wall-mount Managed Switch on a magnetic surface, simply follow the following diagram: 4.2.1 Magnet Installation of WGS-4215-16P2S Step 1: There are six holes in front, using six sets of magnets to install. Please refer to the following. Step 2: Turn the switch to the back, then screw the magnet to the middle hole.
Warning Note As the magnetic mounting does not fix completely, when deploying the switch please be aware that the equipment will not fall or break due to vibration or dragging. Please use the screw from the Magnet kit to avoid breaking the device. 4.3 DIN-rail Mount Installation The DIN-rail kit is included in the package.
Step 2: Lightly insert the DIN-rail into the track. 1 Push 2 Click Step 3: Check whether the DIN-rail is tightly on the track.
5. Web Login 5.1 Starting Web Management The following shows how to start up the Web Management of the Wall-mount Managed Switch. Note the Wall-mount Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Wall-mount Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100) and the default subnet mask is 255.
Logging in to the Wall-mount Managed Switch 1. Use Internet Explorer 8.0 or above Web browser and enter IP address http://192.168.0.100 to access the Web interface. 2. When the following dialog box appears, please enter “admin” in both the default user name and password fields. The login screen in Figure 5-2 appears. Default IP Address: 192.168.0.100 Default Username: admin Default Password: admin Figure 5-2: Web Login Screen 3. After entering the password, the main screen appears as Figure 5-3 shows.
Figure 5-3: Web Main Screen of Wall-mount Managed Switch The Switch Menu on the left of the Web page lets you access all the commands and statistics the Wall-mount Managed Switch provides. Figure 5-4: Switch Menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more.
5.2 Saving Configuration via the Web In the Wall-mount Managed Switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence of runningconfig can be saved from the RAM to FLASH by “Save Configurations to FLASH” function, so that the running configuration sequence becomes the startup configuration file, which is called configuration save.
6. Telnet Login The Wall-mount Managed Switch also supports Telnet for remote management. The switch asks for user name and password for remote login when using Telnet; please use “admin” for both username and password. Default IP address: 192.168.0.100 Username: admin Password: admin Figure 6-1: Wall-mount Managed Switch Telnet Login Screen The user can now enter commands to manage the Wall-mount Managed Switch. For a detailed description of the commands, please refer to the following chapters. 1.
6.1 Configuring IP Address The Wall-mount Managed Switch is shipped with default IP address shown below: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedure as follows: Display of the Current IP Address 1. At the “#” prompt, enter “show ip”. 2. The screen displays the current IP address shown in Figure 6-2. Figure 6-2: IP Information Screen Configuration of the IP Address 3.
The previous command would apply the following settings for the Wall-mount Managed Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.254 Figure 6-3: Configuring IP Address Screen 4. Repeat step 1 to check if the IP address has changed. 6.2 Storing the Current Switch Configuration At the “#” prompt, enter the following command and press .
7. Recovering Back to Default Configuration IP Address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to default value, press the reset button on the front panel for about 5 seconds. After the device is rebooted, you can log in the Web interface management within the same subnet of 192.168.0.xx.
8. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Switch support team email address: support@planet.com.tw WGS-804HPT/WGS-4215-8T/WGS-4215-8T2S/WGS-4215-8P2S/WGS-4215-16P2S User’s Manual: https://www.planet.com.