200Mbps 802.11ac Wave 2 Dual Band Ceiling-mount Wireless Access Point w/802.
Copyright Copyright 2020 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. CE Compliance Statement This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
CONTENTS Chapter 1.Product Introduction ........................................................................................................... 1 1.1 Package Contents ............................................................................................................... 1 1.2 Product Description ............................................................................................................ 2 1.3 Product Features ..................................................................
Appendix A: Planet Smart Discovery Utility ..................................................................................... 90 Appendix B: FAQs ............................................................................................................................... 91 Q1: How to Set Up the AP Client Connection .......................................................................... 91 Q2: How to Set Up the WDS Connection ..........................................................................
FIGURE FIGURE 2-1 WDAP-C7210E TRIPLE VIEWING ..................................................................................................... 12 FIGURE 2-2 WDAP-C7210E FRONT PANEL.......................................................................................................... 13 FIGURE 2-3 WDAP-C7210E REAR PANEL ........................................................................................................... 14 FIGURE 2-4 WDAP-C7210E BOTTOM PANEL .....................................
FIGURE 6-12 ENTER THE PASSWORD .................................................................................................................... 82 FIGURE 6-13 CONNECTED TO THE NETWORK ....................................................................................................... 83 FIGURE 6-14 SYSTEM PREFERENCES .................................................................................................................... 84 FIGURE 6-15 SYSTEM PREFERENCES -- NETWORK ........................
User Manual of WDAP-C7200E Chapter 1. Product Introduction 1.1 Package Contents Thank you for choosing PLANET WDAP-C7210E Wireless AP. Please verify the contents inside the package box. Package Contents of WDAP-C7210E WDAP-C7210E Quick Guide Ethernet Cable Mounting-Kit If there is any item missing or damaged, please contact the seller immediately.
User Manual of WDAP-C7200E 1.2 Product Description Ultra-high-speed, Wave 2 MU-MIMO Wireless LAN Solution PLANET WDAP-C7210E 1200Mbps Wave 2 Dual Band 802.11ac Wireless AP supports central management through PLANET NMS controllers. With IEEE 802.11ac Wave 2 MU-MIMO 2T2R dual-band technology, the WDAP-C7210E provides a maximum wireless speed of 867Mbps at 5GHz and 300Mbps at 2.4GHz. Benefits of MU-MIMO under 802.
User Manual of WDAP-C7200E Powerful Dual-band WLAN Solution PLANET WDAP-C7210E, adopting the IEEE 802.11ac Wave 2 standard, provides a high-speed transmission of power and data, meaning two remote nodes in the 5GHz frequency band can be bridged. The 2.4GHz wireless connection can also be used simultaneously. Furthermore, the WDAP-C7210E adopts the high-class Qualcomm Atheros SoC (System-on-a-Chip), which provides higher stability to meet the stringent requirements of the solution.
User Manual of WDAP-C7200E Multiple Operation Modes for Various Applications The WDAP-C7210E supports AP, Gateway, WISP, Repeater and Super WDS modes, through which it provides more flexibility for users when wireless network is established. Compared with general wireless access points, the WDAP-C7210E offers more powerful and flexible capability for wireless clients. Ceiling-mount Design for Your Environment With the standard IEEE802.
User Manual of WDAP-C7200E Optimized Efficiency in AP Management The brand-new GUI configuration wizard helps the system administrator easily set up the WDAP-C7210E step by step. Besides, the built-in Wi-Fi analyzer provides real-time channel utilization to prevent channel overlapping to assure greater performance. With the automatic transmission power mechanism, distance control and scheduled reboot setting, the WDAP-C7210E is easy for the administrator to deploy and manage without on-site maintenance.
User Manual of WDAP-C7200E Applications Extremely High-speed and Dual Band Make Wi-Fi Transmission More Powerful The WDAP-C7210E delivers the dual band technology to avoid signal interference and ensure the best Wi-Fi performance. It allows you to check e-mails and surf the Internet via the 2.4GHz band and simultaneously watch high-definition (HD) video and any other multimedia application via 5GHz band.
User Manual of WDAP-C7200E -7-
User Manual of WDAP-C7200E 1.3 Product Features Industrial Compliant Wireless LAN and LAN Compliant with the IEEE 802.11a/b/g/n/ac wireless technology Equipped with 10/100/1000Mbps RJ45 ports, auto MDI/MDI-X supported RF Interface Characteristics 802.11ac Wave 2 2T2R MIMO architecture with data rate of up to 1200Mbps (300Mbps at 2.
User Manual of WDAP-C7200E Product Specifications Product WDAP-C7210E 1200Mbps 802.11ac Wave 2 Dual Band Ceiling-mount Wireless Access Point Hardware Specifications Interfaces LAN 2 x 10/100/1000BASE-T RJ45 port Auto-negotiation and auto MDI/MDI-X Antennas Gain: 4 x Internal 5dBi antenna (2.4G x2, 5G x2) Reset Button LED Indicators Reset button on the rear side (Press over 15 seconds to reset the device to factory default) SYS, 2.4G, 5G Dimensions (W x D x H) 186 x 186 x 35.
User Manual of WDAP-C7200E (dBm) ETSI: < 20dBm (EIRP) Network Mode Data Rate Receive Sensitivity (dBm) 1Mbps -99 11Mbps -92 6Mbps -95 54Mbps -82 MCS0/MCS8 -95 MCS7/MCS15 -77 MCS0/MCS8 -93 MCS7/MCS15 -75 6Mbps -92 54Mbps -75 MCS0/MCS8 -91 MCS7/MCS15 -72 MCS0/MCS8 -88 MCS7/MCS15 -70 MCS0 -92 MCS8 -70 MCS0 -89 MCS9 -65 MCS0 -87 MCS9 -61 2.4GHz 802.11b 802.11g 802.11n HT20 802.11n HT40 5GHz Receive Sensitivity 802.11a 802.11n HT20 802.11n HT40 802.
User Manual of WDAP-C7200E Wireless max. 32 MAC addresses filtering User Isolation Max. SSIDs 4 Max. Clients 64 per radio (50 is suggested, depending on usage) Max. WDS Peers 4 Wireless QoS Supports Wi-Fi Multimedia (WMM) Auto Channel Selection 5-level Transmit Power Control (Max.100%, Efficient 75%, Enhanced 50%, Standard 25% or Min. 12.
User Manual of WDAP-C7200E Chapter 2. Hardware Installation 2.1 Product Outlook WDAP-C7210E Dimensions: 186 x 186 x 35.
User Manual of WDAP-C7200E Front Panel Figure 2-2 WDAP-C7210E Front Panel LED Definition LED PWR STATUS FUNCTION On ( Red ) The access point is on. Off System is operating. On Wireless LAN is initializing. Blinking (Blue/Green) 2.4GHz/5GHz wireless LAN is working.
User Manual of WDAP-C7200E Rear Panel Figure 2-3 WDAP-C7210E Rear Panel Bottom Panel Figure 2-4 WDAP-C7210E Bottom Panel Port definition Object 12V DC Description 12V DC port for the power adapter( DC-Jack 5.5 x 2.1mm ) LED The access point is on. PoE LAN port with Power over Ethernet (PoE) IN LAN LAN port connecting to the network equipment. Reset To restore to the factory default setting, press and hold the Reset Button for about 15 seconds, and then release it.
User Manual of WDAP-C7200E Chapter 3. Connecting to the AP 3.1 System Requirements Broadband Internet Access Service (Cable/xDSL/Ethernet connection) One IEEE 802.3at PoE switch (supply power to the WDAP-C7210E) PCs with a working Ethernet adapter and an Ethernet cable with RJ45 connectors PCs running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or later, Linux, UNIX or other platforms compatible with TCP/IP protocols 1.
User Manual of WDAP-C7200E Step 2. Load the device into the mounting bracket, and be sure the device is mated with fixed screws. Then, lock the device in position and plug the Ethernet cable into the WDAP-C7210E. Figure 3-2 Connecting the Ethernet Cable Step 3. Plug the other end of the Ethernet cable into the PoE switch.
User Manual of WDAP-C7200E Chapter 4. Quick Installation Guide This chapter will show you how to configure the basic functions of your AP within minutes. A computer with wired Ethernet connection to the Wireless AP is required for the first-time configuration. 4.1 Manual Network Setup -- TCP/IP Configuration The default IP address of the WDAP-C7210E is 192.168.1.253. And the default subnet mask is 255.255.255.0. These values can be changed as you want.
User Manual of WDAP-C7200E Figure 4-1 TCP/IP Setting Now click OK to save your settings. Now, you can run the ping command in the command prompt to verify the network connection between your PC and the AP. The following example is in Windows 10 OS. Please follow the steps below: 1. Click on Start > Run. 2. Type “cmd” in the Search box.
User Manual of WDAP-C7200E Figure 4-2 Windows Start Menu 3. Open a command prompt, type ping 192.168.1.253 and then press Enter. If the result displayed is similar to Figure 4-3, it means the connection between your PC and the AP has been established well.
User Manual of WDAP-C7200E If the result displayed is similar to Figure 4-4, it means the connection between your PC and the AP has failed. Figure 4-4 Failed Result of Ping Command If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.
User Manual of WDAP-C7200E 4.2 Starting Setup in the Web UI It is easy to configure and manage the AP with the web browser. Step 1. To access the configuration utility, open a web-browser and enter the default IP address http://192.168.1.253 in the web address field of the browser. Figure 4-5 Login by Default IP Address After a moment, a login window will appear. Enter admin for the password in lower case letters. Then click LOGIN or press the Enter key.
User Manual of WDAP-C7200E Chapter 5. Configuring the AP This chapter delivers a detailed presentation of AP’s functionalities and features 3 main items below, allowing you to manage the AP with ease. Figure 5-1 Main Menu The page includes the following fields: Object Description Operation Mode It shows the current mode status. Device Information It shows the CPU/memory usage. Device Description You can enter the device description. Flow (5G Wi-Fi) bps It shows the Upstream/Downstream graph.
User Manual of WDAP-C7200E 5.1 Wizard The Wizard guides you to configuring the WDAP-C7210E in a different mode, including Gateway, Super WDS, WISP, Repeater, AP modes. Figure 5-2 Operation Mode The default operation mode is AP Mode.
User Manual of WDAP-C7200E 5.2 Gateway Mode (Router) Click “Wizard” “Gateway Mode” and the following page will be displayed. This section allows you to configure the Gateway mode.
User Manual of WDAP-C7200E 5.2.1 WAN Settings Static IP If your ISP offers you static IP Internet connection type, select “Static IP" and then enter IP address, subnet mask, default gateway and primary DNS information provided by your ISP in the corresponding fields. Figure 5-4 Gateway -- Static IP The page includes the following fields: Object IP Address Description Enter the WAN IP address provided by your ISP.
User Manual of WDAP-C7200E Figure 5-5 Gateway – PPPoE (ADSL) The page includes the following fields: Object Description Username Enter the PPPoE User Name provided by your ISP Password Enter the PPPoE password provided by your ISP Server Name Enter the server name by your ISP, or not Service Name Enter the service name by your ISP, or not -26-
User Manual of WDAP-C7200E DHCP Choose “DHCP” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP. Figure 5-6 Gateway – DHCP 5.2.
User Manual of WDAP-C7200E Figure 5-7 Gateway – Wireless The page includes the following fields: Object Wi-Fi Status Description Select ON (Green) or OFF (Gray) to enable or disable wireless LAN It is the wireless network name. The default SSID is PLANET_2.4G SSID and PLANET_5G Hide your SSID Select ON (Green) or OFF (Gray) to hide wireless LAN or not Select the operating channel you would like to use. The channel Channel range will be changed by selecting a different domain.
User Manual of WDAP-C7200E 5.3 Super WDS Mode In the Super WDS mode, the wireless interface can be connected with other wireless APs through WDS, and the wireless interface and cable interface. Click “Wizard” “Super WDS Mode” and the following page will be displayed. If you want to use super WDS to do connection, make sure each WDAP-C7210E is already in Super WDS mode before scanning wireless.
User Manual of WDAP-C7200E The page includes the following fields: Object Description Select Network Select network for using 2.4G or 5G to do connection. WDS SSID It is the WDS wireless network name. The default SSID is “Wireless2.4G_WDS” or “Wireless5.8G_WDS”. AP BSSID/Mark Press the “Scan” button to find the WDS BSSID to connect. Select open or WEP for the wireless encryption. The default is None. Encrypt Key in the correct password for BSSID of WEP. In this step you can set up the 2.
User Manual of WDAP-C7200E Figure 5-10 Super WDS Mode – 5G SSID The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN SSID It is the wireless network name. The default SSID is “PLANET_5G” Hide your SSID Select ON (Green) or OFF (Gray) to hide wireless LAN or not Bandwidth Select the operating channel width, “20MHz” or “40MHz” or “80MHz” Channel Select the operating channel you would like to use.
User Manual of WDAP-C7200E Figure 5-17 Super WDS Mode The page includes the following fields: Object Description IP Mode Select “Static IP” or “DHCP Client” for setting up device IP Timing Set time to restart Connection section for example, AP1 – Enter the WDS SSID and encrypt password.
User Manual of WDAP-C7200E Figure 5-18 Super WDS Mode – AP1 AP2 -- Press the “Scan” button to find AP1 BSSID and choose it to connect. Enter the encrypt password.
User Manual of WDAP-C7200E 5.4 WISP Mode Click “Wizard” “WISP Mode” and the following page will be displayed. This section allows you to configure the WISP mode.
User Manual of WDAP-C7200E Figure 5-20 WISP Mode The page includes the following fields: Object Bandwidth Repeater SSID Description Select network for using 2.4G or 5G to do connection. Enter the root AP’s SSID or press “Scan” to select. Lock BSSID Check to lock the root AP’s MAC address. Encryption Select the wireless encryption of root AP. The default “WPA/WPA2PSK_TKIPAES”. Password Enter the password of root AP.
User Manual of WDAP-C7200E Figure 5-21 WISP Mode – Select Internet Mode (Set up WAN type) -36-
User Manual of WDAP-C7200E Figure 5-22 WISP Mode – Setting up Wi-Fi -37-
User Manual of WDAP-C7200E 5.5 Repeater Mode (Universal Repeater) Click “Wizard” “Repeater Mode” and the following page will be displayed. This section allows you to configure the Repeater mode.
User Manual of WDAP-C7200E Figure 5-23 Repeater Mode The page includes the following fields: Object Description Select Network Select “2.4G” or “5.8G” wireless LAN. Repeater SSID Enter the root AP’s SSID or press “Scan” to select. Lock BSSID Check to lock the root AP’s MAC address. Encryption Select the wireless encryption of root AP. The default “WPA/WPA2PSK_TKIPAES”. Password Enter the password of root AP. Bandwidth Select the operating channel width, “20MHz” or “40MHz” or “80MHz”.
User Manual of WDAP-C7200E Figure 5-24 Repeater Mode -- Scan Root AP -40-
User Manual of WDAP-C7200E Set up the repeater wireless network Figure 5-25 Repeater Mode – Setting up Wi-Fi -41-
User Manual of WDAP-C7200E The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN. SSID It is the wireless network name. The default SSID is “PLANET_5G”. Hide your SSID Select ON (Green) or OFF (Gray) to hide wireless LAN or not. Encryption Select the wireless encryption. The default is “None”. Timing Set time to restart.
User Manual of WDAP-C7200E The page includes the following fields: Object Description IP Mode Select “Static IP” or “DHCP Client” for setting up device IP. LAN IP Enter the AP static IP address. Subnet Enter the network mask. Gateway Enter the default gateway IP address. Primary DNS Enter the primary DNS IP address, or not. Secondary DNS Enter the secondary DNS IP address, or not. Enter the LAN IP address.
User Manual of WDAP-C7200E 5.6 AP Mode In the AP mode, the AP wireless interface and cable interface bridge together. Click “Wizard” “AP Mode” and the following page will be displayed. This section allows you to configure the AP mode.
User Manual of WDAP-C7200E The page includes the following fields: Object Description IP Mode Select “Static IP” or “DHCP Client” for setting up device IP. LAN IP Enter the AP static IP address. Subnet Enter the network mask. Gateway Enter the default gateway IP address. Primary DNS Enter the primary DNS IP address, or not. Secondary DNS Enter the secondary DNS IP address, or not. Enter the LAN IP address.
User Manual of WDAP-C7200E Figure 5-28 AP Mode – Set up Wi-Fi The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN. SSID It is the wireless network name. The default SSID is “PLANET_5G”. Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not. Bandwidth Select the operating channel width, “20MHz” or “40MHz” or “80MHz”. Channel Select the operating channel you would like to use.
User Manual of WDAP-C7200E 5.7 Wi-Fi 5.7.1 2.4G/5G Wi-Fi 5.7.1.1.
User Manual of WDAP-C7200E The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN. SSID It is the wireless network name. The default SSID is “PLANET_2.4G” or “PLANET_5G”. Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not. It shows the channel of the CPE. Default 2.4GHz is channel 6.and Channel 5GHz is channel 36. Encryption Select the wireless encryption. The default is “None”.
User Manual of WDAP-C7200E 5.7.2 MAC ACL 5.7.2.1. MAC ACL Figure 5-11 MAC ACL The page includes the following fields: Object Description Add Press the “Add” button to add end-device that is scanned from wireless network and mark them. Delete Press the “Delete” button to delete device from list. Apply Press the “Apply” button to enable/disable the rule. ACL Status Select the rule of ACL, default is Disable.
User Manual of WDAP-C7200E 5.7.3 Wi-Fi Timer Off 5.7.3.1. Wi-Fi Timer Off Figure 5-33 Wi-Fi Timer Off The page includes the following fields: Object Wi-Fi Timer Off Time Frame Description Select ON (Green) or OFF (Gray) to enable or disable timer. Choose the time frame of Wi-Fi.
User Manual of WDAP-C7200E 5.7.4 Advanced 5.7.4.1. Advanced Figure 5-34 Advanced The page includes the following fields: Object 2.4G Mode 5G Mode Description Select 802.11B/G or 802.11N/G in CPE. Select 802.11A or 802.11AN or 802.11AC in CPE. Maximum 2.4G per AP The maximum users are 64. Maximum 5G per AP The maximum users are 64. 2.4G WLAN Partition Enable it to isolate each connected wireless client so that they cannot access mutually.
User Manual of WDAP-C7200E 5G TX Power The range of transmit power is Max (100%), Efficient (75%), Enhanced (50%), Standard (25%) or Min (12.5%). In case of shortening the distance and the coverage of the wireless network, input a smaller value to reduce the radio transmission power. Multicast Fast A part of the 802.11n standard that allows sending multiple frames per single access to the medium by combining frames together into one larger frame.
User Manual of WDAP-C7200E 5.7.5 Network 5.7.5.1. LAN Settings Figure 5-35 LAN Settings The page includes the following fields: Object Description IP Mode Select “Static IP” or “DHCP Client” for setting up device IP. LAN IP Enter the AP static IP address. Subnet Enter the network mask. Gateway Primary DNS Secondary DNS 5.7.5.2. Enter the default gateway IP address. Enter the primary DNS IP address, or not. Enter the secondary DNS IP address, or not.
User Manual of WDAP-C7200E The page includes the following fields: Object Description Read Community Enter the read community, default is public. Write Community Enter the write community, default is private. Trap Destination Address 5.7.5.3. Enter the SNMP trap IP address, default is 192.168.1.100. VLAN Settings Figure 5-37 VLAN Settings The page includes the following fields: Object AP VLAN ID Description Select AP or VAP included in the VLAN. Enter the VLAN ID from 3 to 4094.
User Manual of WDAP-C7200E 5.7.5.4. WAN Settings Static IP If your ISP offers you static IP Internet connection type, select “Static IP" and then enter IP address, subnet mask, default gateway and primary DNS information provided by your ISP in the corresponding fields. Figure 5-38 Static IP The page includes the following fields: Object IP Address Description Enter the WAN IP address provided by your ISP. Enquire your ISP if you are not clear. Subnet Enter WAN Subnet Mask provided by your ISP.
User Manual of WDAP-C7200E Figure 5-39 PPPoE (ADSL) The page includes the following fields: Object Description Username Enter the PPPoE User Name provided by your ISP. Password Enter the PPPoE password provided by your ISP. Server Name Enter the server description or not. Service Name Enter the service description or not. MTU Maximum Transmission Unit. Default is 1452. Set DNS Manually Enable/Disable DNS Manually. Primary DNS Enter the necessary DNS address provided by your ISP.
User Manual of WDAP-C7200E Figure 5-40 DHCP The page includes the following fields: Object Description MTU Maximum Transmission Unit. Default is 1452. Set DNS Manually Enable/Disable DNS Manually. Primary DNS Enter the necessary DNS address provided by your ISP. Secondary DNS Enter the secondary DNS address provided by your ISP. Band Type Select the band type provided by your ISP. Upstream Enter limited upstream throughput, default is 1000000 Kbps.
User Manual of WDAP-C7200E The page includes the following fields: Object Description Enable web server access on Enable to access from WAN, default port is 8080 WAN port MAC clone Enable and scan to clone the MAC address Enable Ping Access on WAN Enable or Disable this function Enable IPsec passthrough on VPN connection Enable or disable IPSec to pass through IPSec communication data. Enable PPTP passthrough on VPN connection Enable or disable PPTP to pass through PPTP communication data.
User Manual of WDAP-C7200E Figure 5-24 URL Filtering The page includes the following fields: Object Description Add Press the “Add” button to add the rule Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g. Black list Time Group Select Any or Customer to set up time range and work data.
User Manual of WDAP-C7200E 5.7.6.2. IP/Port Filtering Figure 5-44 IP/Port Filtering The page includes the following fields: Object Description Add Press the “Add” button to add the rule in the black or white list Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g.
User Manual of WDAP-C7200E Port Range Enter the web port to access Protocol Select TCP, UDP or TCP+UDP Mark Enter the mark string, or not IP/Port Filtering Status Select the rule of IP/Port Filtering, default is Disable. Whitelist: Allow the devices to pass in the rule Blacklist: Prohibited rules within the device through Figure 5-45 IP/Port Filtering 5.7.6.3.
User Manual of WDAP-C7200E Figure 5-46 MAC Filtering The page includes the following fields: Object Description Add Press the “Add” button to add the rule in the black or white list Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g. Black list Time Group Select Any or Customer to set up time range and work data.
User Manual of WDAP-C7200E Figure 5-47 IP/Port Filtering 5.7.6.4. Security (Port Mapping/Port Forwarding) Figure 5-48 Port Mapping The page includes the following fields: Object Description Add Press the “Add” button to add the rule in the black or white list Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g.
User Manual of WDAP-C7200E LAN IP Enter the IP address that you need for port forwarding External Port Enter the external port range Internal Port Enter the internal port range Mark Enter the mark string, or not Enable/disable Port Mapping function Figure 5-49 Port Mapping 5.7.6.5.
User Manual of WDAP-C7200E 5.7.7 Management 5.7.7.1.
User Manual of WDAP-C7200E 5.7.7.2. Reboot Figure 5-15 Reboot The page includes the following fields: Object Description Reboot Reboot device immediately Timed Reboot Select Enable or Disable to start schedule reboot Reboot Time Select reboot time for clock Restart Interval Select reboot duty by day 5.7.7.3.
User Manual of WDAP-C7200E Confirm Password Enter new password again 5.7.7.4. Upgrade Figure 5-54 Upgrade Firmware The page includes the following fields: Object Choose File Description Press to select the firmware file Whether to resume the factory configuration Upgrade Select to reset the device to default when upgrading firmware Press to upgrade the firmware Note: Do not power off during the process of upgrading the software 5.7.7.5.
User Manual of WDAP-C7200E The page includes the following fields: Object Description System Time Show system time of device NTP Enable Select Enable or Disable NTP function Time Zone Select Select time zone Manual IP Settings Enable to manual IP setting NTP Server Select NTP server Sync with Host Press to sync system time with host server Note: If you want to use any function that needs scheduling, must enable NTP function. 5.7.7.6.
User Manual of WDAP-C7200E Export Export a log.bin file to you PC Delete Press to delete all of the system log Refresh Press to refresh the system log 5.7.7.7.
User Manual of WDAP-C7200E Figure 5-59 Adding rule of flow control(Speed Limit) The page includes the following fields: Object Description Status Select enable or disable flow control rule IP Group Select custom or Add an IP group IP Address Enter an IP address range or use scan to select Time Group Select any or custom or Add a Time group Limited Mode Select limited mode for shared limited bandwidth or exclusive limited bandwidth Up Enter the upstream limited for kbps Down Enter the downst
User Manual of WDAP-C7200E 5.7.7.8.
User Manual of WDAP-C7200E The page includes the following fields: Object Description Group Name Enter an IP group description IP Address Enter an IP address range or use scan to select Mark Enter the mark string, or not 5.7.7.9.
User Manual of WDAP-C7200E Figure 5-18 Add Time Group The page includes the following fields: Object Description Time Group Enter an time group description Time Range Select start time and end time for time range Work Date Select work day by option table Mark Enter the mark string, or not -73-
User Manual of WDAP-C7200E 5.7.7.10. DDNS Setting Figure 5-64 DDNS Setting The page includes the following fields: Object Description DDNS Select ON (Green) or OFF (Gray) to enable or disable PLANET DDNS DDNS Option Select PLANET DDNS or Easy DDNS function User Name Enter user account for PLANET DDNS. If you use Easy DDNS it was not necessary. Password Enter password for PLANET DDNS. If you use Easy DDNS it was not necessary. Domain Enter unique domain name for device.
User Manual of WDAP-C7200E Figure 5-65 PLANET EasyDDNS -75-
User Manual of WDAP-C7200E Chapter 6. Quick Connection to a Wireless Network In the following sections, the default SSID of the WDAP-C7210E is configured to “default”. 6.
User Manual of WDAP-C7200E Step 4: Enter the encryption key of the wireless AP (1) The Wireless Network Connection box will appear (2) Enter the encryption key that is configured in section 5.7.2.1 (3) Click the [Connect] button Figure 6-3 Entering the Network Key Step 5: Check if “Connected” is displayed Figure 6-4 Choosing a Wireless Network -- Connected Some laptops are equipped with a “Wireless ON/OFF” switch for the internal wireless LAN.
User Manual of WDAP-C7200E 6.2 Windows 7/8/10 (WLAN AutoConfig) WLAN AutoConfig service is built-in in Windows 7 that can be used to detect and connect to wireless network. This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP.
User Manual of WDAP-C7200E Step 4: Enter the encryption key of the wireless AP (1) The Connect to a Network box will appear. (2) Enter the encryption key that is configured in section 5.7.2.1 (3) Click the [OK] button.
User Manual of WDAP-C7200E Step 5: Check if “Connected” is displayed.
User Manual of WDAP-C7200E 6.3 Mac OS X 10.x In the following sections, the default SSID of the WDAP-C7210E is configured to “default”. Step 1: Right-click on the network icon displayed in the system tray The AirPort Network Connection menu will appear. Figure 6-10 Mac OS – Network Icon Step 2: Highlight and select the wireless network (SSID) to connect (1) Select and SSID [default]. (2) Double-click on the selected SSID.
User Manual of WDAP-C7200E Step 4: Enter the encryption key of the wireless AP (1) Enter the encryption key that is configured in section 5.7.2.1 (2) Click the [OK] button. Figure 6-12 Enter the Password If you will be connecting to this Wireless AP in the future, check [Remember this network].
User Manual of WDAP-C7200E Step 5: Check if the AirPort is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in front of the SSID.
User Manual of WDAP-C7200E There is another way to configure the MAC OS X wireless settings: Step 1: Click and open the [System Preferences] by going to Apple > System Preference or Applications Figure 6-14 System Preferences Step 2: Open Network Preference by clicking on the [Network] icon Figure 6-15 System Preferences -- Network -84-
User Manual of WDAP-C7200E Step 3: Check Wi-Fi setting and select the available wireless network (1) Choose the AirPort on the left menu (make sure it is ON) (2) Select Network Name [default] here If this is the first time to connect to the Wireless AP, it should show “No network selected”.
User Manual of WDAP-C7200E 6.4 iPhone/iPod Touch/iPad In the following sections, the default SSID of the WDAP-C7210E is configured to “default”. Step 1: Tap the [Settings] icon displayed in the home screen Figure 6-17 iPhone – Settings icon Step 2: Check Wi-Fi setting and select the available wireless network (1) Tap [General] \ [Network] (2) Tap [Wi-Fi] If this is the first time to connect to the Wireless AP, it should show “Not Connected”.
User Manual of WDAP-C7200E Figure 6-19 Wi-Fi Setting – Not Connected Step 3: Tap the target wireless network (SSID) in “Choose a Network…” (1) Turn on Wi-Fi by tapping “Wi-Fi” (2) Select SSID [default] Figure 6-20 Turning on Wi-Fi -87-
User Manual of WDAP-C7200E Step 4: Enter the encryption key of the Wireless AP (1) The password input screen will be displayed. (2) Enter the encryption key that is configured in section 5.7.2.1 (3) Tap the [Join] button.
User Manual of WDAP-C7200E Step 5: Check if the device is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in front of the SSID.
User Manual of WDAP-C7200E Appendix A: Planet Smart Discovery Utility To easily list the WDAP-C7210E in your Ethernet environment, the Planet Smart Discovery Utility is an ideal solution. The following installation instructions guide you to running the Planet Smart Discovery Utility. Step 1: Deposit the Planet Smart Discovery Utility in administrator PC. Step 2: Run this utility and the following screen appears.
User Manual of WDAP-C7200E Appendix B: FAQs Q1: How to Set Up the AP Client Connection Topology: -91-
User Manual of WDAP-C7200E Step 1. Use static IP in the PCs that are connected with AP-1(Site-1) and AP-2(Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”. Step 2. In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252. Step 3. In AP-1, go to “Wizard” to configure it to AP Mode. In AP-2, configure it to Repeater Mode.
User Manual of WDAP-C7200E AP-2 Step 4. In AP-2, press Scan AP to search the AP-1. You can also enter the MAC address, SSID, encryption and bandwidth if you know what they are.
User Manual of WDAP-C7200E Step 5. Click “Next” to finish the setting. Step 6. Click “Repeater Information” to check connection status.
User Manual of WDAP-C7200E Step 7. Use command line tool to ping each other to ensure the link is successfully established. From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100. Step 8. Configure the TCP/IP settings of Site-2 to “Obtain an IP address automatically”.
User Manual of WDAP-C7200E Step 9. Use command line tool to ping the DNS (e.g., Google) to ensure Site-2 can access internet through the wireless connection. The following hints should be noted: 1) The encryption method must be the same as that of both sites if configured. 2) Both sites should be Line-of-Sight. 3) For the short distance connection less than 1km, please reduce the "RF Output Power" of both sites.
User Manual of WDAP-C7200E Q2: How to set up the WDS Connection Topology: Step 1. Use static IP in the PCs that are connected with WDAP-C7210E-1 (Site-1) and WDAP-C7210E-2 (Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
User Manual of WDAP-C7200E Step 2. In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252. Step 3. In both APs, go to “Wizard” to configure it in Super WDS Mode. Step 4. In AP1 set up WDS SSID, for example WDS-1. Select Encrypt for WEP and enter password.
User Manual of WDAP-C7200E Step 5. Finish the 2.4G/5G Wi-Fi and LAN setting. Step 6. Click “Home” to check WDS status. Step 7. In AP2 scan AP1 WDS SSID, for example WDS-1. Select Encrypt for WEP and enter password.
User Manual of WDAP-C7200E -100-
User Manual of WDAP-C7200E Step 8. Confirm SSID and MAC. Select Encrypt for WEP and enter password. Step 9. Finish the 5G Wi-Fi and LAN setting. Step 10. Go to “WDS Information” to check connection status.
User Manual of WDAP-C7200E Step 11. Use command line tool to ping each other to ensure the link is successfully established. From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100. The following hints should be noted: 1) The encryption method must be the same as that of both sites if configured. 2) Both sites should be Line-of-Sight. 3) For the short distance connection less than 1m, please reduce the "RF Output Power" of both sites.
User Manual of WDAP-C7200E Appendix C: Troubleshooting If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the dealer for help. Some problems can be solved by yourself within a very short time. Scenario Solution The AP is not responding to a. Please check the connection of the power cord and the Ethernet cable of this AP. All cords and cables should be me when I want to access it correctly and firmly inserted into the AP.
User Manual of WDAP-C7200E Scenario Solution i. Try to use IP address instead of host name. If you can use IP address to communicate with a remote server, but can’t use host name, please check DNS setting. I can’t locate my AP by my a. ‘Broadcast ESSID’ set to off? wireless device. b. Both two antennas are properly secured. c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled.
User Manual of WDAP-C7200E Appendix D: Glossary 802.11ac - 802.11ac is a wireless networking standard in the 802.11 family (which is marketed under the brand name Wi-Fi), developed in the IEEE Standards Association process, providing high-throughput wireless local area networks (WLANs) on the 5 GHz band. 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output).
User Manual of WDAP-C7200E NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet. PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network.
User Manual of WDAP-C7200E EC Declaration of Conformity English Hereby, PLANET Technology Corporation, declares that this 11ac Wireless AP is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Lietuviškai Šiuo PLANET Technology Corporation,, skelbia, kad 11ac Wireless AP tenkina visus svarbiausius 2014/53/EU direktyvos reikalavimus ir kitas svarbias nuostatas.
