802.
Copyright Copyright 2020 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body. CE Compliance Statement This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
Revision User Manual of PLANET 802.11ac 900Mbps Outdoor Wireless CPE Model: WBS-512AC Rev: 1.0 (May, 2020) Part No. EM-WBS-512AC_v1.
CONTENTS Chapter 1.Product Introduction ........................................................................................................... 1 Package Contents ............................................................................................................... 1 Product Description ............................................................................................................ 2 Product Features ...................................................................................
Mac OS X 10.x .................................................................................................................... 58 iPhone/iPod Touch/iPad ................................................................................................... 62 Appendix A: Planet Smart Discovery Utility ..................................................................................... 65 Appendix B: FAQs .......................................................................................................
FIGURE FIGURE 2-1 WBS-512AC FRONT SIDE ...................................................................................................... 9 FIGURE 2-2 WBS-512AC REAR SIDE ........................................................................................................ 9 FIGURE 2-3 WBS-512AC RIGHT SIDE ..................................................................................................... 10 FIGURE 2-4 WBS-512AC RIGHT SIDE .............................................................
FIGURE 5-30 VLAN ................................................................................................................................. 41 FIGURE 5-31 SNMP ................................................................................................................................ 42 FIGURE 5-32 STATIC IP............................................................................................................................ 43 FIGURE 5-33 PPPOE (ADSL)........................................
User Manual of WBS-512AC Chapter 1. Product Introduction Package Contents Thank you for choosing PLANET WBS-512AC Wireless AP. Please verify the contents inside the package box. Package Contents of WBS-512AC/WBS-512AC WBS-512AC Quick Guide Ethernet Cable Mounting Strap If there is any item missing or damaged, please contact the seller immediately.
User Manual of WBS-512AC Product Description Flexible and Reliable Outdoor Wireless Solution with Superior Performance PLANET WBS-512AC 802.11ac WAVE 2 900Mbps Outdoor Wireless CPE offers a better range and excellent throughput than those of the traditional wireless device. With the standard IEEE 802.3at Power over Ethernet (PoE) design, the WBS-512AC can be easily installed in the areas where power outlets are not available.
User Manual of WBS-512AC Multiple SSIDs with VLAN Tagging The WBS-512AC supports WPA/WPA2, and the 802.1X RADIUS authentication to secure the wireless connection. Besides, the supported IEEE 802.1Q VLAN allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the wireless access. This makes it possible for the WBS-512ACN to work with managed Ethernet switches to have VLANs assigned to a different access level and authority.
User Manual of WBS-512AC Optimized Efficiency in AP Management The brand-new GUI configuration wizard helps the system administrator easily set up the WBS-512AC step by step. Besides, the built-in Wi-Fi analyzer provides real-time channel utilization to prevent channel overlapping to assure greater performance. With the automatic transmission power mechanism, distance control and scheduling reboot setting, the WBS-512AC is easy for the administrator to deploy and manage without on-site maintenance.
User Manual of WBS-512AC Product Features Industrial Compliant Wireless LAN and LAN Compliant with the IEEE 802.
User Manual of WBS-512AC Product Specifications Product WBS-512AC 900Mbps Outdoor Wireless CPE Wave 2.0, MU-MIMO Hardware IEEE 802.11a/n/ac IEEE 802.11i Standard Support IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3x flow control IEEE 802.11k, 802.11v, and 802.11r Dimensions (W x D x H) 87 x 38 x 260mm Weight 405g Power Requirements Power Consumption (max.) 48V DC IN, 0.5A, IEEE 802.3 at PoE+ or 12V DC IN, 1.0A from DC Jack < 10W Wireless IEEE 802.
User Manual of WBS-512AC 802.11n HT40 802.11ac VHT20 802.11ac VHT40 802.
User Manual of WBS-512AC Wi-Fi channel analysis chart Fast Roaming(IEEE 802.11k, 802.11r, 802.11v) Device status, wireless client List Status Monitoring PLANET Smart Discovery DHCP client table System Log supports remote syslog server VLAN IEEE 802.
User Manual of WBS-512AC Chapter 2.
User Manual of WBS-512AC Right Side Figure 2-3 WBS-512AC Right Side LED Definitions LED State Meaning On The device is powered on Off The device is powered off On Port linked Blinking Data is transmitting or receiving data Off No link On Port linked Blinking Data is transmitting or receiving data Off No link On The wireless radio is on Blinking Data is transmitting or receiving over wireless Off The wireless radio is off Power WAN Port LAN Port WLAN -10-
User Manual of WBS-512AC 2.1.1 Port and Button It provides a simple interface monitoring the AP. Figure 2-4 shows the hardware-based interface of the WBS512AC. WBS-512AC Hardware-based Interface: PtP Switch LAN WAN/PoE Reset/Pair DC Power Figure 2-4 WBS-512AC Interface 2.1.
User Manual of WBS-512AC Chapter 3. Connecting to the CPE System Requirements Broadband Internet Access Service (Cable/xDSL/Ethernet connection) One IEEE 802.3at PoE switch (supply power to the WBS-512AC) PCs with a working Ethernet adapter and an Ethernet cable with RJ45 connectors PCs running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or later, Linux, UNIX or other platforms compatible with TCP/IP protocols 1.
User Manual of WBS-512AC Step 2. Plug the RJ45 Ethernet cable into the PoE Port of the Outdoor Wireless CPE. Then, slide back the cover to finish the installation. Figure 3-2 Connect the Ethernet cable Step 3. Place the mounting strap through the slot on the back of the Outdoor Wireless CPE and then around the pole. Tighten the mounting strap to secure the Outdoor Wireless CPE.
User Manual of WBS-512AC Chapter 4. Quick Installation Guide This chapter will show you how to configure the basic functions of your CPE within minutes. A computer with wired Ethernet connection to the Wireless CPE is required for the first-time configuration. Manual Network Setup -- TCP/IP Configuration The default IP address of the WBS-512AC is 192.168.1.253. And the default Subnet Mask is 255.255.255.0. These values can be changed as you want.
User Manual of WBS-512AC Figure 4-1 TCP/IP Setting Now click OK to save your settings. Now, you can run the ping command in the command prompt to verify the network connection between your PC and the AP. The following example is in Windows 10 OS. Please follow the steps below: 1. Click on Start > Run. 2. Type “cmd” in the Search box.
User Manual of WBS-512AC Figure 4-2 Windows Start Menu 3. Open a command prompt, type ping 192.168.1.253 and then press Enter. If the result displayed is similar to Figure 4-3, it means the connection between your PC and the AP has been established well.
User Manual of WBS-512AC If the result displayed is similar to Figure 4-4, it means the connection between your PC and the AP has failed. Figure 4-4 Failed Result of Ping Command If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.
User Manual of WBS-512AC Starting Setup in the Web UI It is easy to configure and manage the CPE with the web browser. Step 1. To access the configuration utility, open a web-browser and enter the default IP address http://192.168.1.253 in the web address field of the browser. Figure 4-5 Login by Default IP Address After a moment, a login window will appear. Enter admin for the password in lower case letters. Then click LOGIN or press the Enter key. Figure 4-6 Login Window Default IP Address: 192.168.
User Manual of WBS-512AC Chapter 5. Configuring the CPE This chapter delivers a detailed presentation of CPE’s functionalities and features 3 main items below, allowing you to manage the CPE with ease. Figure 5-1 Main Menu The page includes the following fields: Object Description Operation Mode It shows the current mode status. Device Information It shows the CPU/memory usage. Device Description You can enter the device description. Flow (5G Wi-Fi) bps It shows the Upstream/Downstream graph.
User Manual of WBS-512AC Figure 5-2 Operation Mode The default operation mode is AP mode. Change the PtP switch to optional AP/repeater mode. Gateway Mode Click “Wizard” “Gateway Mode” and the following page will be displayed. This section allows you to configure the Gateway mode.
User Manual of WBS-512AC 5.2.1 WAN Settings Static IP If your ISP offers you static IP Internet connection type, select “Static IP" and then enter IP address, subnet mask, default gateway and primary DNS information provided by your ISP in the corresponding fields. Figure 5-4 Gateway -- Static IP The page includes the following fields: Object IP Address Description Enter the WAN IP address provided by your ISP.
User Manual of WBS-512AC Figure 5-5 Gateway – PPPoE (ADSL) The page includes the following fields: Object Description Username Enter the PPPoE User Name provided by your ISP Password Enter the PPPoE password provided by your ISP Server Name Enter the server name by your ISP, or not Service Name Enter the service name by your ISP, or not -22-
User Manual of WBS-512AC DHCP Choose “DHCP” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP. Figure 5-6 Gateway – DHCP 5.2.
User Manual of WBS-512AC The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN SSID It is the wireless network name. The default SSID is PLANET_5G Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not Select the operating channel you would like to use. The channel Channel range will be changed by selecting a different domain. Encryption Select the wireless encryption.
User Manual of WBS-512AC “Wireless5.8G_WDS” AP BSSID/Mark Press the “Scan” button to find the WDS BSSID to connect Select open or WEP for the wireless encryption. The default is None Encryption Key in the correct password for BSSID of WEP Figure 5-9 Super WDS Mode The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN SSID It is the wireless network name.
User Manual of WBS-512AC Figure 5-10 Super WDS Mode The page includes the following fields: Object Description IP Mode Select “Static IP” or “DHCP Client” for setting up device IP Timing Set time to restart -26-
User Manual of WBS-512AC AP1 – Enter the WDS SSID and encrypt password. Figure 5-11 Super WDS Mode – AP1 AP2 -- Press the “Scan” button to find AP1 BSSID and choose it to connect. Enter the encrypt password. Figure 5-12 Super WDS Mode – AP2 WISP Mode Click “Wizard” “WISP Mode” and the following page will be displayed. This section allows you to configure the WISP mode.
User Manual of WBS-512AC Figure 5-13 WISP Mode The page includes the following fields: Object Repeater SSID Description Enter the root AP’s SSID or press “Scan” to select Lock BSSID Check to lock the root AP’ MAC address Encryption Select the wireless encryption of root AP.
User Manual of WBS-512AC Figure 5-14 WISP Mode – Select Internet Mode (Set up WAN type) Figure 5-14 WISP Mode – Setting up Wi-Fi -29-
User Manual of WBS-512AC AP Mode Click “Wizard” “AP Mode” and the following page will be displayed. This section allows you to configure the AP mode.
User Manual of WBS-512AC Figure 5-15 AP Mode – Set up Wi-Fi The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN SSID It is the wireless network name. The default SSID is “PLANET_5G” Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not Bandwidth Select the operating channel width, “20MHz” or “40MHz” or “80MHz” Channel Select the operating channel you would like to use.
User Manual of WBS-512AC Repeater Mode Click “Wizard” “Repeater Mode” and the following page will be displayed. This section allows you to configure the Repeater mode. Figure 5-16 Repeater Mode The page includes the following fields: Object Repeater SSID Description Enter the root AP’s SSID or press “Scan” to select Lock BSSID Check to lock the root AP’ MAC address Encryption Select the wireless encryption of root AP.
User Manual of WBS-512AC Press the “Scan” button to find the root AP that you need to repeat and press Choice to select the AP.
User Manual of WBS-512AC The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN SSID It is the wireless network name. The default SSID is “PLANET_5G” Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not Encryption Select the wireless encryption.
User Manual of WBS-512AC Wi-Fi 5.7.1 5G Wi-Fi 5.7.1.1. Basic Figure 5-20 Basic The page includes the following fields: Object Description Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable wireless LAN SSID It is the wireless network name. The default SSID is “PLANET_5G” Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not Channel It shows the channel of the CPE. Default 5GHz is channel 36. Encryption Select the wireless encryption.
User Manual of WBS-512AC 5.7.1.2. VAP Figure 5-21 VAP Select VAP1~VAP3 to enable virtual AP The page includes the following fields: Object Description Select ON (Green) or OFF (Gray) to enable or disable virtual wireless Wi-Fi Status SSID LAN It is the wireless network name. The default SSID is “PLANET_5G_1” to “PLANET_5G_3” Hide your SSID？ Select ON (Green) or OFF (Gray) to hide wireless LAN or not Channel It shows the channel of the CPE. Default 5GHz is channel 36.
User Manual of WBS-512AC 5.7.2 MAC ACL 5.7.2.1. MAC ACL Figure 5-9 MAC ACL The page includes the following fields: Object Description Add Press the “Add” button to add end-device that is scanned from wireless network and mark them Delete Press the “Delete” button to delete device from list Apply Press the “Apply” button to enable/disable the rule ACL Status Select the rule of ACL, default is Disable.
User Manual of WBS-512AC 5.7.3 Wi-Fi Timer Off 5.7.3.1.
User Manual of WBS-512AC 5.7.4 Advanced 5.7.4.1. Advanced Figure 5-24 Advanced The page includes the following fields: Object 5G Mode Maximum 5G per AP 5G WLAN Partition Description Select 802.11A or 802.11AN or 802.11AC in CPE The maximum users are 64 Enable it to isolate each connected wireless client so that they cannot access mutually. 5G Coverage Threshold The coverage threshold is to limit the weak signal of clients occupying session.
User Manual of WBS-512AC send an RTS frame to the destination wireless node, and the latter will reply with a CTS frame, and thus they are ready to communicate. The default value is 2346 RTS Threshold Enable or Disable RTS/CTS protocol. It can be used in the following scenarios and used by Stations or Wireless AP. 1) When medium is too noisy or lots of interferences are present. If the AP/Station cannot get a chance to send a packet, the RTS/CTS mechanism can be initiated to get the packet sent.
User Manual of WBS-512AC 5.7.5 Network 5.7.5.1. LAN Settings Figure 5-25 LAN Settings The page includes the following fields: Object Description IP Mode Select “Static IP” or “DHCP Client” for setting up device IP LAN IP Enter the AP static IP address Subnet Enter the network mask Gateway Primary DNS Secondary DNS 5.7.5.2.
User Manual of WBS-512AC The page includes the following fields: Object Description Read Community Enter the read community, default is public Write Community Enter the write community, default is private Trap Destination Address 5.7.5.3. Enter the SNMP trap IP address, default is 192.168.1.100 VLAN Settings Figure 5-11 VLAN Settings The page includes the following fields: Object Select AP or VAP included in the VLAN AP VLAN ID 5.7.5.4.
User Manual of WBS-512AC Figure 5-12 Static IP The page includes the following fields: Object IP Address Description Enter the WAN IP address provided by your ISP. Enquire your ISP if you are not clear Subnet Enter WAN Subnet Mask provided by your ISP Default Gateway Enter the WAN Gateway address provided by your ISP MTU Maximum Transmission Unit.
User Manual of WBS-512AC Figure 5-13 PPPoE (ADSL) The page includes the following fields: Object Description Username Enter the PPPoE User Name provided by your ISP Password Enter the PPPoE password provided by your ISP Set DNS Manually Enable/Disable DNS Manually Primary DNS Enter the necessary DNS address provided by your ISP Secondary DNS Enter the secondary DNS address provided by your ISP MTU Maximum Transmission Unit.
User Manual of WBS-512AC Figure 5-14 DHCP The page includes the following fields: Object Description MTU Maximum Transmission Unit.
User Manual of WBS-512AC Object Description Enable web server access on Enable to access from WAN, default port is 8080 WAN port MAC clone Enable and scan to clone the MAC address Enable Ping Access on WAN Enable or Disable this function Enable IPsec passthrough on VPN connection Enable or disable IPSec to pass through IPSec communication data. Enable PPTP passthrough on VPN connection Enable or disable PPTP to pass through PPTP communication data.
User Manual of WBS-512AC Figure 5-36 URL Filtering The page includes the following fields: Object Description Add Press the “Add” button to add the rule Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g. Black list Time Group Select Any or Customer to set up time range and work data.
User Manual of WBS-512AC 5.7.6.2. IP/Port Filtering Figure 5-38 IP/Port Filtering The page includes the following fields: Object Description Add Press the “Add” button to add the rule in the black or white list Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g.
User Manual of WBS-512AC Port Range Enter the web port to access Protocol Select TCP, UDP or TCP+UDP Mark Enter the mark string, or not IP/Port Filtering Status Select the rule of IP/Port Filtering, default is Disable. Whitelist: Allow the devices to pass in the rule Blacklist: Prohibited rules within the device through Figure 5-39 IP/Port Filtering 5.7.6.3.
User Manual of WBS-512AC Figure 5-40 MAC Filtering The page includes the following fields: Object Description Add Press the “Add” button to add the rule in the black or white list Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g. Black list Time Group Select Any or Customer to set up time range and work data.
User Manual of WBS-512AC Figure 5-41 IP/Port Filtering 5.7.6.4. Security (Port Mapping/Port Forwarding) Figure 5-42 Port Mapping The page includes the following fields: Object Description Add Press the “Add” button to add the rule in the black or white list Delete Press the “Delete” button to delete the rule Apply Press the “Apply” button to enable/disable the rule Status Select ON (Green) or OFF (Gray) to enable or disable Rule Name Enter the rule name, e.g.
User Manual of WBS-512AC LAN IP Enter the IP address that you need for port forwarding External Port Enter the external port range Internal Port Enter the internal port range Mark Enter the mark string, or not Enable/disable Port Mapping function Figure 5-43 Port Mapping 5.7.6.5.
User Manual of WBS-512AC Chapter 6. Quick Connection to a Wireless Network In the following sections, the default SSID of the WBS-512AC is configured to “default”.
User Manual of WBS-512AC Step 4: Enter the encryption key of the wireless AP (1) The Wireless Network Connection box will appear (2) Enter the encryption key that is configured in section 5.7.1.
User Manual of WBS-512AC Some laptops are equipped with a “Wireless ON/OFF” switch for the internal wireless LAN. Make sure the hardware-based wireless switch is switched to “ON” position. Windows 7 (WLAN AutoConfig) WLAN AutoConfig service is built-in in Windows 7 that can be used to detect and connect to wireless network. This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP.
User Manual of WBS-512AC If you will be connecting to this Wireless AP in the future, check [Connect automatically]. Step 4: Enter the encryption key of the wireless AP (1) The Connect to a Network box will appear (2) Enter the encryption key that is configured in section 5.7.1.
User Manual of WBS-512AC Step 5: Check if “Connected” is displayed Figure 6-9 Connected to a Network -57-
User Manual of WBS-512AC Mac OS X 10.x In the following sections, the default SSID of the WBS-512AC is configured to “default”.
User Manual of WBS-512AC Figure 6-12 Enter the Password If you will be connecting to this Wireless AP in the future, check [Remember this network]. Step 5: Check if the AirPort is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in front of the SSID.
User Manual of WBS-512AC There is another way to configure the MAC OS X wireless settings: Step 1: Click and open the [System Preferences] by going to Apple > System Preference or Applications Figure 6-14 System Preferences Step 2: Open Network Preference by clicking on the [Network] icon Figure 6-15 System Preferences -- Network -60-
User Manual of WBS-512AC Step 3: Check Wi-Fi setting and select the available wireless network (1) Choose the AirPort on the left-menu (make sure it is ON) (2) Select Network Name [default] here If this is the first time to connect to the Wireless AP, it should show “No network selected”.
User Manual of WBS-512AC iPhone/iPod Touch/iPad In the following sections, the default SSID of the WBS-512AC is configured to “default”. Step 1: Tap the [Settings] icon displayed in the home screen Figure 6-17 iPhone – Settings icon Step 2: Check Wi-Fi setting and select the available wireless network (1) Tap [General] \ [Network] (2) Tap [Wi-Fi] If this is the first time to connect to the Wireless AP, it should show “Not Connected”.
User Manual of WBS-512AC Figure 6-19 Wi-Fi Setting – Not Connected Step 3: Tap the target wireless network (SSID) in “Choose a Network…” (1) Turn on Wi-Fi by tapping “Wi-Fi” (2) Select SSID [default] Figure 6-20 Turning on Wi-Fi Step 4: Enter the encryption key of the Wireless AP (1) The password input screen will be displayed (2) Enter the encryption key that is configured in section 5.7.1.
User Manual of WBS-512AC Figure 6-21 iPhone -- Entering the Password Step 5: Check if the device is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in front of the SSID.
User Manual of WBS-512AC Appendix A: Planet Smart Discovery Utility To easily list the WBS-512A in your Ethernet environment, the Planet Smart Discovery Utility is an ideal solution. The following installation instructions guide you to running the Planet Smart Discovery Utility. Step 1: Download the Planet Smart Discovery Utility from the administrator PC. Step 2: Run this utility and the following screen appears.
User Manual of WBS-512AC Appendix B: FAQs Q1: How to set up the AP Client Connection Topology: Step1. Use static IP in the PCs that are connected with AP-1 (Site-1) and AP-2 (Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
User Manual of WBS-512AC Step2. In AP-2, change the PtP switch to slave, the default IP is 192.168.1.100. Step 3. In AP-1, go to “Wizard” to configure it to AP Mode. In AP-2, configure it to Repeater Mode. AP-1 AP-2 Step 4. In AP-2, press Scan AP to search the AP-1. You can also enter the MAC address, SSID, encryption and bandwidth if you know what they are.
User Manual of WBS-512AC Step 5. Click “Next” to finish the setting. Step 6. Go to “Repeater Information” to check connection status.
User Manual of WBS-512AC Step 7. Use command line tool to ping each other to ensure the link is successfully established. From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100. Step 8. Configure the TCP/IP settings of Site-2 to “Obtain an IP address automatically”.
User Manual of WBS-512AC Step 9. Use command line tool to ping the DNS (e.g., Google) to ensure Site-2 can access internet through the wireless connection. The following hints should be noted: 1) The encryption method must be the same as that of both sites if configured. 2) Both sites should be Line-of-Sight. 3) For the short distance connection less than 1km, please reduce the "RF Output Power" of both sites.
User Manual of WBS-512AC Step 1. Use static IP in the PCs that are connected with WBS-512AC-1 (Site-1) and WBS-512AC-2 (Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
User Manual of WBS-512AC Step 2. In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252. Step 3. In both APs, go to “Wizard” to configure it in Super WDS Mode. Step 4. In AP1 set up WDS SSID, for example WDS-1. Select Encrypt for WEP and enter password.
User Manual of WBS-512AC Step 5. Finish the 5G Wi-Fi and LAN setting. Step 6. Click “Home” to check WDS status. Step 7. In AP2 scan AP1 WDS SSID, for example WDS-1. Select Encrypt for WEP and enter password.
User Manual of WBS-512AC Step 8.Confirm SSID and MAC. Select Encrypt for WEP and enter password. Step 9. Finish the 5G Wi-Fi and LAN setting. Step 10. Go to “WDS Information” to check connection status.
User Manual of WBS-512AC Step 11. Use command line tool to ping each other to ensure the link is successfully established. From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100. The following hints should be noted: 1) The encryption method must be the same as that of both sites if configured. 2) Both sites should be Line-of-Sight. 3) For the short distance connection less than 1km, please reduce the "RF Output Power" of both sites.
User Manual of WBS-512AC Appendix C: Troubleshooting If you find the AP is working improperly or stops responding to you, please read this troubleshooting first before contacting the dealer for help. Some problems can be solved by yourself within a very short time. Scenario Solution The AP is not responding to a. Please check the connection of the power cord and the Ethernet cable of this AP. All cords and cables should be me when I want to access it correctly and firmly inserted into the AP.
User Manual of WBS-512AC i. Try to use IP address instead of host name. If you can use IP address to communicate with a remote server, but can’t use host name, please check DNS setting. I can’t locate my AP by my a. ‘Broadcast ESSID’ set to off? wireless device. b. Both two antennas are properly secured. c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled. File downloading is very slow a.
User Manual of WBS-512AC Appendix D: Glossary 802.11ac - 802.11ac is a wireless networking standard in the 802.11 family (which is marketed under the brand name Wi-Fi), developed in the IEEE Standards Association process, providing high-throughput wireless local area networks (WLANs) on the 5 GHz band. 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multipleoutput).
User Manual of WBS-512AC MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be transmitted. NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet. PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.
User Manual of WBS-512AC EC Declaration of Conformity English Hereby, PLANET Technology Corporation, declares that this 900Mbps 802.11ac Wireless Outdoor CPE is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Česky Společnost PLANET Technology Corporation, tímto prohlašuje, že tato 900Mbps 802.11ac Wireless Outdoor CPE splňuje základní požadavky a další příslušná ustanovení směrnice 2014/53/EU.
