5-Port 10/100/1000T VPN Security Router VR-100 5-Port 10/100/1000T VPN Security Router VR-100 -1-
5-Port 10/100/1000T VPN Security Router VR-100 Copyright Copyright (C) 2019 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
5-Port 10/100/1000T VPN Security Router VR-100 – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.
5-Port 10/100/1000T VPN Security Router VR-100 Table of Contents Chapter 1. Product Introduction ............................................................................................. 6 1.1 Package Contents ...................................................................................................... 6 1.2 Overview .................................................................................................................... 6 1.3 Topology ........................................
-Port 10/100/1000T VPN Security Router VR-100 4.6 4.5.3 LAN Setup..............................................................................................47 4.5.4 Routing...................................................................................................48 4.5.5 WAN IPv6 Setting ..................................................................................50 4.5.6 DHCP .....................................................................................................
5-Port 10/100/1000T VPN Security Router VR-100 Chapter 1. Product Introduction 1.1 Package Contents The package should contain the following: VR-100 x 1 Quick Installation Guide x 1 Power Cord x 1 Feet Pads x 4 If any of the above items are missing, please contact your dealer immediately. 1.2 Overview Powerful VPN Security Solution The innovation of the Internet has created tremendous worldwide opportunities for e-business and information sharing.
5-Port 10/100/1000T VPN Security Router VR-100 Excellent Ability in Threat Defense The VR-100 built-in SPI (Stateful Packet Inspection) firewall and Blocking DoS/DDoS attack functions provide high efficiency and extensive protection for your network. Virtual Server and DMZ functions can let you setup servers in the Intranet and still provide services to the Internet users.
5-Port 10/100/1000T VPN Security Router VR-100 Cybersecurity Network Solution to Minimize Security Risks The cybersecurity feature included to protect the switch management in a mission-critical network virtually needs no effort and cost to install. For efficient management, the VR-100 is equipped with HTTPS web and SNMP management interfaces. With the built-in web-based management interface, the VR-100 offers an easy-to-use, platform independent management and configuration facility.
5-Port 10/100/1000T VPN Security Router VR-100 -9-
5-Port 10/100/1000T VPN Security Router VR-100 1.3 Topology PLANET VR-100 VPN security router has an SPI firewall with DoS detection. Through the Content Filtering function, it can easily block the websites like Facebook, YouTube, Gmail, etc. With IPSec/GRE/PPTP/L2TP/SSL VPN solutions, the VR-100 provides secured data communication for branches, vendors, and mobile workers with a flexible way to connect back to the headquarters. The VR-100 connects dual WANs with up to two different ISPs.
5-Port 10/100/1000T VPN Security Router VR-100 1.4 Features Hardware 5 10/100/1000BASE-T RJ45 ports 1 undefined Ethernet port (LAN/WAN) Dual-WAN function 1 USB 3.
5-Port 10/100/1000T VPN Security Router VR-100 MAC address clone DDNS: PLANET DDNS, PLANET Easy DDNS, DynDNS and No-IP Cybersecurity Others Setup wizard Dashboard for real time system overview Supported access by HTTP or HTTPS Auto reboot PLANET Smart Discovery utility/UNI-NMS supported - 12 -
5-Port 10/100/1000T VPN Security Router VR-100 1.5 Product Specifications Product VPN security router Model VR-100 Hardware 5 10/100/1000BASE-T RJ45 Ethernet ports including Ethernet 3 LAN ports 1WAN port 1 LAN/WAN port USB Port 1 USB 3.
5-Port 10/100/1000T VPN Security Router VR-100 Outbound load balancing Failover for dual-WAN Port forwarding DMZ Others Cybersecurity Dashboard Setup wizard Auto reboot PLANET Smart Discovery utility/UNI-NMS supported VPN VPN Function IPSec (Host to Host) GRE PPTP server L2TP SSL (Open VPN) VPN Tunnels Max. 60 VPN Throughput Max.
5-Port 10/100/1000T VPN Security Router VR-100 Chapter 2. Hardware Introduction 2.1 Physical Descriptions 2.1.1 Front View LED PWR Internet Lights up when the power is on. Green Lights up when the router connects to internet successfully. “Steady on” indicates the port is connected to other network device. Port 1-5 “Blink” to indicate there is traffic on the port. Ports USB Port USB 3.0 port for system configuration backup and restoration.
5-Port 10/100/1000T VPN Security Router VR-100 panel of the device and the other end into an electrical outlet, and the power will be ready. 2.1.
5-Port 10/100/1000T VPN Security Router VR-100 2.2 Hardware Installation 2.2.1 Desktop Installation To install the VR-100 on desktop, simply follow the following steps: Step 1: Place the device on desktop. Step 2: Keep enough ventilation space between the device and the surrounding objects. When choosing a location, please keep in mind the environmental restrictions should be under the specifications of the VR-100. Step 3: Connect your device to hub / switch. A.
5-Port 10/100/1000T VPN Security Router VR-100 Step 1: Place your device on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the device with supplied screws attached to the package. In the picture below, it shows how to attach brackets to one side of the device. You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate the warranty.
5-Port 10/100/1000T VPN Security Router VR-100 - 19 -
5-Port 10/100/1000T VPN Security Router VR-100 Chapter 3. Preparation Before getting into the device’s web UI, user has to check the network setting and configure PC’s IP address. 3.1 Requirements User is able to confirm the following items before configuration: 1. Please confirm the network is working properly; it is strongly suggested to test your network connection by connecting your computer directly to ISP. 2. Suggested operating systems: Windows 7 / 8 / 10. 3.
5-Port 10/100/1000T VPN Security Router VR-100 3.2 Setting TCP/IP on your PC The default IP address of the VR-100 is 192.168.1.1, and the DHCP Server is on. Please set the IP address of the connected PC as DHCP client, and the PC will get IP address automatically from the VR-100. Please refer to the following to set the IP address of the connected PC. 3.2.1 Windows 7/8 If you are using Windows 7/8, please refer to the following: 1.
5-Port 10/100/1000T VPN Security Router VR-100 2. Click "Change adapter settings". 3. Right-click on the Local Area Connection and select Properties.
5-Port 10/100/1000T VPN Security Router VR-100 4. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties or directly double-click on Internet Protocol Version 4 (TCP/IPv4).
5-Port 10/100/1000T VPN Security Router VR-100 5. Select "Use the following IP address" and "Obtain DNS server address automatically", and then click the “OK” button.
5-Port 10/100/1000T VPN Security Router VR-100 3.2.2 Windows 10 If you are using Windows 10, please refer to the following: 1. In the search box on the taskbar, type “View network connections”, and then select View network connections at the top of the list.
5-Port 10/100/1000T VPN Security Router VR-100 2. Right-click on the Local Area Connection and select Properties. 3. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties or directly double-click on Internet Protocol Version 4 (TCP/IPv4).
5-Port 10/100/1000T VPN Security Router VR-100 4. Select "Use the following IP address" and "Obtain DNS server address automatically", and then click the “OK” button.
5-Port 10/100/1000T VPN Security Router VR-100 3.3 Planet Smart Discovery Utility For easily listing the router in your Ethernet environment, the search tool -- Planet Smart Discovery Utility -- is an ideal solution. The following installation instructions are to guide you to running the Planet Smart Discovery Utility. 1. Download the Planet Smart Discovery Utility in administrator PC. 2. Run this utility as the following screen appears.
5-Port 10/100/1000T VPN Security Router VR-100 1. This utility shows all necessary information from the devices, such as MAC address, device name, firmware version, and device IP subnet address. It can also assign new password, IP subnet address and description to the devices. 2. After setup is completed, press the “Update Device”, “Update Multi” or “Update All” button to take effect. The functions of the 3 buttons above are shown below: Update Device: use current setting on one single device.
5-Port 10/100/1000T VPN Security Router VR-100 Chapter 4. Web-based Management This chapter provides setup details of the device’s Web-based Interface. 4.1 Introduction The device can be configured with your Web browser. Before configuring, please make sure your PC is under the same IP segment with the device. 4.2 Logging in to the VPN Router Refer to the steps below to configure the VPN router: Step 1.
5-Port 10/100/1000T VPN Security Router VR-100 4.3 Main Web Page After a successful login, the main web page appears. The web main page displays the web panel, main menu, function menu, and the main information in the center. Figure 4-: Main Web Page ■ Web Panel The web panel displays an image of the device’s ports as shown in Figure 4-2. Figure 4-2: Web Panel Object Icon Function To indicate the LAN with the RJ45 plug-in.
5-Port 10/100/1000T VPN Security Router VR-100 ■ Main Menu The main menu displays the product name, function menu, and main information in the center. Via the Web management, the administrator can set up the device by selecting the functions those listed in the function menu and button as shown in Figures 4-3 and 4-4. Figure 4-3: Function Menu Object Description System Provides System information of the router. Network Provides WAN, LAN and network configuration of the router.
5-Port 10/100/1000T VPN Security Router VR-100 4.4 System Use the System menu items to display and configure basic administrative details of the router. The System menu shown in Figure 4-5 provides the following features to configure and monitor system. Figure 4-5: System Menu Object Wizard Description The Wizard will guide the user to configuring the router easily and quickly. Dashboard The overview of system information includes connection, port, and system status.
5-Port 10/100/1000T VPN Security Router VR-100 4.4.1 Setup Wizard The Wizard will guide the user to configuring the router easily and quickly. There are different procedures in different operation modes. According to the operation mode you switch to, please follow the instructions below to configure the router via Setup Wizard as shown in Figure 4-6. Figure 4-6: Setup Wizard Step 1: LAN Interface Set up the IP Address and Subnet Mask for the LAN interface as shown in Figure 4-7.
5-Port 10/100/1000T VPN Security Router VR-100 Start IP Address By default, the start IP address is 192.168.1.100. Please do not set it to the same IP address of the router. By default, the maximum DHCP users are 101, which means the router Maximum DHCP Users will provide DHCP client with IP address from 192.168.1.100 to 192.168.1.200 when the start IP address is 192.168.1.100. Next Cancel Press this button to the next step.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-9: Setup Wizard – WAN 2 Configurations Mode 1 -- Static IP Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter the IP Address, Netmask, Default Gateway and DNS Server provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x).
5-Port 10/100/1000T VPN Security Router VR-100 Next Press this button for the next step. Previous Press this button for the previous step. Press this button to undo any changes made locally and revert Cancel to previously saved values. Mode 2 -- DHCP Client Select DHCP Client to obtain IP Address information automatically from your ISP. The setup is shown in Figure 4-11. Figure 4-11: WAN Interface Setup – DHCP Setup Step 3: Security Setting Set up the Security Settings as shown in Figure 4-12.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description The SPI Firewall prevents attack and improper access to network SPI Firewall resources. The default configuration is enabled. SYN Flood is a popular attack way. DoS and DDoS are TCP Block SYN Flood protocols. Hackers like using this method to make a fake connection that involves the CPU, memory, and so on. The default configuration is enabled.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-13: Setup Wizard –Setup Completed Object Description Finish Press this button to save and apply changes. Previous Press this button for the previous step.
5-Port 10/100/1000T VPN Security Router VR-100 4.4.2 Dashboard The dashboard provides an overview of system information including connection, port, and system status as shown in Figure 4-14. Figure 4-14: Dashboard WAN/LAN Connection Status Object Description The status means WAN is connected to Internet and LAN is connected. The status means WAN is disconnected to Internet and LAN is connected. The status means WAN is connected to Internet and LAN is disconnected.
5-Port 10/100/1000T VPN Security Router VR-100 Ethernet port is not in use. USB port is in use. USB port is not in use. System Information Object Description CPU Display the CPU loading Memory Display the memory usage 4.4.3 Status This page displays system information as shown in Figure 4-15.
5-Port 10/100/1000T VPN Security Router VR-100 4.4.4 Statistics This page displays the number of packets that pass through the router on the WAN and LAN. The statistics are shown in Figure 4-16. Figure 4-16: Statistics 4.4.5 Connection Status The page will show the DHCP Table and ARP Table. .
5-Port 10/100/1000T VPN Security Router VR-100 4.4.6 SNMP This page provides SNMP setting of the router as shown in Figure 4-18. Figure 4-18: SNMP Object Enable SNMP Description Disable or enable the SNMP function. The default configuration is enabled. Read/Write Community Allows entering characters for SNMP Read/Write Community of the router. System Name Allows entering characters for system name of the router. System Location Allows entering characters for system location of the router.
5-Port 10/100/1000T VPN Security Router VR-100 4.5 Network The Network function provides WAN, LAN and network configuration of the router as shown in Figure 4-19. Figure 4-19: Network Menu Object Description WAN Setup Allows setting WAN interface. WAN Advanced Allows setting WAN Advanced settings. LAN Setup Allows setting LAN interface. Routing Allows setting Route. IPv6 Allows setting IPv6 WAN interface. DHCP Allows setting DHCP Server. DDNS Allows setting DDNS and PLANET DDNS.
5-Port 10/100/1000T VPN Security Router VR-100 4.5.1 WAN This page is used to configure the parameters for Internet network which connects to the WAN port of the router as shown in Figure 4-20. Here you may select the access method by clicking the item value of WAN access type. Figure 4-20: WAN Object Description Please select the corresponding WAN Access Type for the Internet, and fill out the correct parameters from your local ISP in the fields which appear below.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description Netmask Enter the Subnet Mask assigned by your ISP. Gateway Enter the Gateway assigned by your ISP. DNS Server The DNS server information will be supplied by your ISP. DHCP Select DHCP Client to obtain IP Address information automatically from your ISP. WAN IP, whether obtained automatically or specified manually, should NOT be on the same IP net segment as the LAN IP; otherwise, the router will not work properly.
5-Port 10/100/1000T VPN Security Router VR-100 Object Load Balance Weight External Connection Detection Detect Interval Description Load Balance Weight allows you to set a relative weight (from 1 - 10) for each WAN port. Enable to detect the status of WAN connection. Set the detect interval as you need. The recommended value is 5 (default). Detect Link Up Set the times for detecting link up. Threshold The recommended value is 8 (default). Detect Link Down Set the times for detecting link down.
5-Port 10/100/1000T VPN Security Router VR-100 4.5.4 Routing Please refer to the following sections for the details as shown in Figures 4-23 and 24. Figure 4-23: Routing table Figure 4-24: Routing setup Routing tables contain a list of IP addresses. Each IP address identifies a remote router (or other network gateway) that the local router is configured to recognize.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description The gateway is the router or host’s IP address to which packet was Gateway sent. It must be the same network segment with the WAN or LAN port. Interface Comment Select the interface that the IP packet must use to transmit out of the router when this route is used. Enter any words for recognition.
5-Port 10/100/1000T VPN Security Router VR-100 4.5.5 WAN IPv6 Setting This page is used to configure parameter for IPv6 internet network which connects to WAN port of the router as shown in Figure 4-25. It allows you to enable IPv6 function and set up the parameters of the router’s WAN. In this setting you may change WAN connection type and other settings. Figure 4-25: IPv6 WAN setup Object Description Connection Type Select IPv6 WAN type either by using DHCP or Static.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-26: DHCP Object Description By default, the DHCP Server is enabled, meaning the router will DHCP Service assign IP addresses to the DHCP clients automatically. If user needs to disable the function, please set it as disable. Start IP Address By default, the start IP address is 192.168.1.100. Please do not set it to the same IP address of the router.
5-Port 10/100/1000T VPN Security Router VR-100 4.5.7 DDNS The router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address, and then your friends can connect to your server by entering your domain name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as PLANET DDNS (http://www.planetddns.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-27: PLANET DDNS Object DDNS Service Interface Description By default, the DDNS service is disabled. If user needs to enable the function, please set it as enable. User is able to select the interface for DDNS service. By default, the interface is WAN 1. There are three options: DDNS Type 1. PLANET DDNS: Activate PLANET DDNS service. 2. DynDNS: Activate DynDNS service. 3. NOIP: Activate NOIP service.
5-Port 10/100/1000T VPN Security Router VR-100 4.5.8 MAC Address Clone Clone or change the MAC address of the WAN interface. The setup is shown in Figure 4-28. Figure 4-28: MAC Address Clone Object Description Clone WAN MAC Set the function as enable or disable. MAC Address Input a MAC Address, such as A8:F7:E0:00:06:62.
5-Port 10/100/1000T VPN Security Router VR-100 4.6 Security The Security menu provides Firewall, Access Filtering and other functions as shown in Figure 4-29. Please refer to the following sections for the details. Figure 4-29: Security menu Object Description Firewall Allows setting DoS (Denial of Service) protection as enable. MAC Filtering Allows setting MAC Filtering. IP Filtering Allows setting IP Filtering. Web Filtering Allows setting Web Filtering.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.1 Firewall A "Denial-of-Service" (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service. The router can prevent specific DoS attacks as shown in Figure 4-30. Figure 4-30: Firewall Object Description The SPI Firewall prevents attack and improper access to network SPI Firewall resources. The default configuration is enabled. SYN Flood is a popular attack way.
5-Port 10/100/1000T VPN Security Router VR-100 If the function is enabled, when the number of the current Block UDP Flood UPD-FLOOD packets is beyond the set value, the router will start the blocking function immediately. The default configuration is disabled. ICMP is kind of a pack of TCP/IP; its important function is to transfer Block ICMP Flood simple signal on the Internet. There are two normal attack ways which hackers like to use, Ping of Death and Smurf attack.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.2 MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network or Internet through the router. Use of such filters can be helpful in securing or restricting your local network as shown in Figure 4-31. Figure 4-31: MAC Filtering Object Description Set the function as enable or disable. Enable MAC Filtering When the function is enabled, the router will block traffic of the MAC address on the list.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.3 IP Filtering IP Filtering is used to deny LAN users from accessing the public IP address on internet as shown in Figure 4-32. To begin blocking access to an IP address, enable IP Filtering and enter the IP address of the web site you wish to block. Figure 4-32: IP Filtering Object Description IP Filtering Set the function as enable or disable. Add IP Filtering Rule Go to the Add Filtering Rule page to add a new rule.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description Destination IP Address Input the IP address of web site which you want to block. Anywhere (of destination Check the box if you want to control all web sites, meaning the LAN IP Address) user can’t visit any web site. Destination Port Input the port of destination IP Address which you want to block. Leave it as blank if you want to block all ports of the web site. Select the protocol type (TCP, UDP or all).
5-Port 10/100/1000T VPN Security Router VR-100 Object Description Set the rule as enable or disable. Status Input the URL address that you want to filter, such as Filter Keyword www.yahoo.com. 4.6.5 Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall as shown in Figure 4-36.
5-Port 10/100/1000T VPN Security Router VR-100 Object Rule Name Description Enter any words for recognition. Select the protocol type (TCP, UDP or both). If you are unsure, Protocol please leave it to the default both protocols. Enter the external ports you want to control. For TCP and UDP External Service Port services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description Enter the IP address of a particular host in your LAN which will DMZ IP Address receive all the packets originally going to the WAN port/Public IP address above.
5-Port 10/100/1000T VPN Security Router VR-100 4.7 VPN To obtain a private and secure network link, the router is capable of establishing VPN connections. When used in combination with remote client authentication, it links the business’ remote sites and users, conveniently providing the enterprise with an encrypted network communication method.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.7 IPSec IPSec (IP Security) is a generic standardized VPN solution. IPSec must be implemented in the IP stack which is part of the kernel. Since IPSec is a standardized protocol it is compatible to most vendors that implement IPSec. It allows users to have an encrypted network session by standard IKE (Internet Key Exchange). We strongly encourage you to use IPSec only if you need to because of interoperability purposes.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-41: IPSec Tunnel Object Description IPSec Tunnel Enable Check the box to enable the function. Tunnel Name Enter any words for recognition. This is only available for host-to-host connections and specifies to Interface which interface the host is connecting. 1. WAN 1. 2. WAN 2. Local Network The local subnet in CIDR notation. For instance, "192.168.1.0”. Local Netmask The netmask of this router.
5-Port 10/100/1000T VPN Security Router VR-100 Remote IP Address Input the IP address of the remote host. For instance, "210.66.1.10”. Remote Network The remote subnet in CIDR notation. For instance, "210.66.1.0”. Remote Netmask The netmask of the remote host. Set up the detection time of DPD (Dead Peer Detection). By default, the DPD detection’s gap is 30 seconds, over 150 seconds to think that is the broken line.
5-Port 10/100/1000T VPN Security Router VR-100 by using it three times. It can achieve an algorithm up to 168 bits. 3. SHA1: The SHA1 is a revision of SHA. It has improved the shortcomings of SHA. By producing summary hash values, it can achieve an algorithm up to 160 bits. 4. SHA2: Either 256, 384 or 512 can be chosen. 5. MD5 Algorithm: MD5 processes a variably long message into a fixed-length output of 128 bits. You can specify how long ESP packets are valid.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-43: GRE Tunnel Object Description Active Check the box to enable the function. Tunnel Name Enter any words for recognition. This is only available for host-to-host connections and specifies to which interface the host is connecting. Through 1. LAN. 2. WAN 1. 3. WAN 2. Peer WAN IP Address Input the IP address of the remote host. For instance, "210.66.1.10”. Peer Netmask The remote subnet in CIDR notation. For instance, "210.66.1.0/24”.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.9 PPTP Server Use the IP address and the scope option needs to match the far end of the PPTP server; its goal is to use the PPTP channel technology, and establish Site-to-Site VPN where the channel can have equally good results from different methods with IPSec. The PPTP server is shown in Figure 4-44. Figure 4-44: PPTP server Object Description PPTP Server Set the function as enable or disable. Broadcast Enter any words for recognition.
5-Port 10/100/1000T VPN Security Router VR-100 MSCHAP v2 DNS WINS Server IP Address Set the authentication as enable or disable. When the PPTP client connects to the PPTP server, it will assign the DNS server IP address to client. When the PPTP client connects to the PPTP server, it will assign the WINS server IP address to client. Input the IP address of the PPTP Server. For instance, "192.168.10.1”.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.10 L2TP Server This section assists you in setting the L2TP Server as shown in Figure 4-45. Figure 4-45: L2TP Server Object Description L2TP Server Set the function as enable or disable. Server IP Address Input the IP address of the L2TP Server. For instance, "192.168.50.1”. When the VPN connection is established, the VPN client will get IP Clients IP Address address from the VPN Server. Please set the range of IP Address.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description With IPsec Set the function as enable to make the L2TP work with IPsec encryption. Preshare Key Enter a pass phrase. User and Password Create the username and password for the VPN client. Connection Type 1. Main. 2. Aggressive. It provides the way to create the SA between two PCs. The SA can access the encoding between two PCs, and the IT administrator can assign to which key size or Preshare Key and algorithm to use.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.11 SSL VPN This section assists you in setting the SSL Server as shown in Figure 4-46. Figure 4-46: SSL Server Object Description SSL VPN Server Set the function as enable or disable. Port Set a port for the SSL Service. Default port is 1194. Tunnel Protocol Set the protocol as TCP or UDP. Virtual Network Device Set the Virtual Network Device as TUN or TAP. Interface User is able to select the interface for SSL service using.
5-Port 10/100/1000T VPN Security Router VR-100 4.6.12 VPN Connection This page shows the VPN connection status as shown in Figure 4-47. Figure 4-47: VPN Connection Status Object Description VPN Connection Click the IPSec/GRE/…/SSL VPN bookmark to check the current Status connection status.
5-Port 10/100/1000T VPN Security Router VR-100 4.7 Maintenance The Maintenance menu provides the following features for managing the system as Figure 4-48 is shown below: Figure 4-48: Maintenance Menu Object Description Administrator Allows changing the login username and password. Date & Time Allows setting Date & Time function. Save/Restore Export the router’s configuration to local or USB sticker. Configuration Restore the router’s configuration from local or USB sticker.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-48: Administrator Object Description Username Input a new username. Password Input a new password. Confirm Password Input password again. 4.7.2 Date and Time This section assists you in setting the system time of the router. You are able to either select to set the time and date manually or automatically obtain the GMT time from Internet as shown in Figure 4-49.
5-Port 10/100/1000T VPN Security Router VR-100 set its time based on your selection. NTP Client Update NTP Server Once this function is enabled, router will automatically update current time from NTP server. User may use the default NTP sever or input NTP server manually. 4.7.3 Saving/Restoring Configuration This page shows the status of the configuration.
5-Port 10/100/1000T VPN Security Router VR-100 Object USB Storage Description The status of USB storage. Backup Settings to Press the USB Storage button to save setting file to USB storage. Load Settings from Press the USB Storage button to upload setting file from USB storage. Before removing the USB storage from the router, please press the Unmount button first. 4.7.4 Upgrading Firmware This page provides the firmware upgrade of the router as shown in Figure 4-51.
5-Port 10/100/1000T VPN Security Router VR-100 Figure 4-52: Reboot/Reset Object Description Reboot Press the button to reboot system. Reset Press the button to restore all settings to factory default settings. I'd like to keep the network profiles. Check the box and then press the button to keep the current network profiles and reset all other configurations to factory defaults. 4.7.6 Diagnostics The page is allows you to issue ICMP PING packets to troubleshoot IP connectivity issues.
5-Port 10/100/1000T VPN Security Router VR-100 Object Description Interface Select an interface of the router. Target Host The destination IP Address or domain. Number of Packets Set the number of packets will be transmitted; the maximum is 100. Ping The time of ping. Be sure the target IP address is within the same network subnet of the router, or you have to set up the correct gateway IP address.
5-Port 10/100/1000T VPN Security Router VR-100 Appendix A: DDNS Application Configuring PLANET DDNS steps: Step 1: Visit DDNS provider’s web site and register an account if you do not have one yet. For example, register an account at http://planetddns.com Step 2: Enable DDNS option through accessing web page of the device. Step 3: Input all DDNS settings.
