Internet Telephony Gateway VIP-050 / VIP-450 User’s Manual Rev 2.
SIP Voice Gateway User’s Manual FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
SIP Voice Gateway User’s Manual How to Use This Manual This manual was designed for the technical and non-technical users of PLANET Internet telephony gateway VIP-050 / VIP-450. It contains information about the functions of VIP and instructions for its installation, basic configuration and operation in related chapters, and introduces more advanced command line interface, firmware upgrade and appendix information. Read this section carefully for important information about the manual’s organization.
SIP Voice Gateway User’s Manual Important Safety Instructions Before plugging VIP into an electrical outlet, carefully read all the installation instructions in Chapter 2. For your own safety and the safety of your equipment, always take the following precautions: · Follow instructions and warnings in the documentation. · Never push any object through the fan vent or other openings in the equipment. Such action may produce a short circuit, causing fire, electric shock, or equipment damage.
SIP Voice Gateway User’s Manual LED Light Emitting Diode PBX Private Branch Exchange PSTN Public Switched Telephone Network RTP Real-Time Transport SIP Session Initialization Protocol TCID Telephony Channel Identifier TFTP Trivial File Transfer Protocol TIM Telephony Interface Modules TNV Telephone Network Voltage UDP User Datagram Protocol UTP Unshielded Twisted Pair VAD Voice Activity Detection WAN Wide Area Network Notation Conventions Throughout this guide, different type styl
SIP Voice Gateway User’s Manual Table of Contents Chapter 1 Overview 1.1 Features 1 1.2 Networking Protocols 1 1.3 Package Contents 2 1.4 Front Panel 2 1.5 Rear Panel 3 Chapter 2 Installing VIP 5 2.1 Network Requirements 5 2.2 2.3 Installing VIP Connecting to the telephony devices 5 5 2.4 2.5 2.6 Connecting to the Network Providing Power to VIP Assigning IP address to VIP 5 6 6 Chapter 3 VIP Concepts 7 3.1 3.2 3.3 How VIP Operates ATPM Destination 7 7 7 3.4 3.5 3.
SIP Voice Gateway User’s Manual 4.2.5 Channel Parameters 4.2.6 Network Connection 4.3 Configure System Settings 4.3.1 IP Settings 4.3.2 SIP Parameters 23 24 28 30 30 Chapter 5 Troubleshooting Tips 34 Chapter 6 Command Line Interface 35 6.1 Connection through Serial Port 35 6.2 Connection through Telnet 35 6.3 Command Help 36 6.4 Designating IP Address 36 6.5 6.6 6.7 Designating Port Number Command Reference Utility Commands 36 37 38 6.8 Network Commands 6.
SIP Voice Gateway User’s Manual B.
VIP User’s Manual Chapter 1 Overview This chapter illustrates an overview of PLANET Internet Telephony Gateway Family – VIP-050 / VIP-450 and a detailed product description of features and capabilities. 1.1 Features Via growth of Internet technology, Internet telephony service plays and turns into a cost-effective and highly reliable substitution system of the old-time traditional PBX system.
SIP Voice Gateway User’s Manual 1.3 Package Contents The contents of your product should contain the following items: VIP-050 l 2-slot Internet Telephony Gateway l Power cord l 9-pin straight through RS-232 cable l Quick Installation Guide l User’s Manual CD l Rack mount Accessories VIP-450 4-port Internet Telephony Gateway Power cord 9-pin straight through RS-232 cable Quick Installation Guide User’s Manual CD l l l l l 1.
SIP Voice Gateway User’s Manual PWR Green On Power is supplied to the gateway. SYSTEM Green Blinking The system is running. (Heartbeat LED) LAN Ÿ ACT Ÿ 100M Green Green Ÿ LNK Ÿ COL Green Green On On Off On On Data is presented on LAN. The gateway is connected to LAN at 100Mb/s. The gateway is connected to LAN at 10Mb/s. The gateway is connected to LAN. Data collision is occurring on the network connection. Slot A/B Channels 1-4 Green Off On Blinking The line is idle.
SIP Voice Gateway User’s Manual Slot A 90~240VA 1 Slot B SLOT A SLOT B ELITE-FXO ELITE-FXS 2 1 2 3 4 50~60H VIP-050 Rear Panel VIP-450 Rear Panel Note: For VIP-050, three modules available, VIP-FXS, VIP-FXO and VIP-E&M. Modules are not included, please consult your local dealer for the information of the modules.
VIP User’s Guide Chapter 2 Installing VIP This chapter gives information on how to install VIP. 2.1 Network Requirements For VIP successfully operate in your network, your network must meet the following requirements: 1. A working 10/100 Base-T Ethernet. VIP connects to Internet via an Ethernet LAN. 2. IP network that supports gateway, and subnet mask. You’ll need one static IP address to assign VIP. 2.2 Installing VIP VIP can be used in a desktop configuration.
VIP User’s Manual 2.5 Providing Power to VIP To provide AC power to VIP complete the following steps: 1. Turn the power switch on the rear panel of VIP to the off position. 2. Connect one end of the power cord that came with VIP to the power receptacle on the rear panel. 3. Connect the other end of the power cord to an AC power outlet. 4. Turn the power switch on. VIP will perform power on self-test.
VIP User’s Manual Chapter 3 VIP Concepts VIP enables the transmission of voice and fax traffic over any IP network by digitizing voice and fax signals, encapsulating the information within IP packets, and then sending the packets across the IP network 3.1 How VIP Operates 1. The TIM inside VIP digitizes analog voice signals at 8 Kbps. 2. VIP system software handles the: Ÿ Capture of telephone number presented as DTMF tones. Ÿ Mapping the telephone number to the IP address of remote VIP.
VIP User’s Manual 3.4 Hunt Group Instead of directly mapping a phone number to a destination, the ATPM first maps the phone number to a group of destinations known as a Hunt Group. A hunt group is a group of destinations that are equivalent. For example, the customer support group of a company might have 20 peo- ple who can handle support calls. Access to customer support is through a single phone number but the next available support person is actually connected upon each incoming call.
SIP Voice Gateway User’s Manual Hunt Group Table The hunt group table maps a hunt group to a list of destinations. Hunt group sample Group id Type #Members Member ids ---------------------------------------------------------------------------1 2 1 1 3 2 1 2 5 2 1 4 11 2 1 11 Destination Table The destination table maps a destination to a telephony port or the IP address of a remote VIP.
VIP User’s Manual Chapter 4 Configuring VIP from a Web Browser This chapter explains procedures for configuring VIP from the web browser. 4.1 Http setting mode This section describes the processes for setting up Internet Telephony Gateway once it has been installed. Microsoft Explorer version 4 or higher, or Navigator version 4.5 or higher can be used in this section to view and change parameters. PC Setup In order to configure VIP, PC needs to have TCP/IP protocol and a compatible IP Address. 1.
VIP User’s Manual 5. On the IP Address table, enter values as follows: · Specify an IP address set ON. · IP Address: 192.168.0.2 · Subnet Mask: 255.255.255.0 Restart your PC and Start your WEB browser. 6. In the Address box, enter the following: http://192.168.0.1 (default IP address of the Voice Gateway) 7. Press enter to confirm and you should find the screen below. 8. The User Name is administrator (all lower case) . P assword is 123. Both administrator and 123 are default strings from factory).
SIP Voice Gateway User’s Manual 4.1.1 Dial Plan/ Dial Settings Main Menu Function Briefings 1.Dial Plan Settings, which helps you configure the dial plan. You should complete the dial plan work sheets before working on this menu. 2.View System Configurations, which includes the specific information related to version, network, SIP, coder, and the channel of the gateway you are using. 3.Configure System Settings, which allows you to modify the system parameters as you wish.
VIP User’s Manual 4.1.1.1 Phone number Please select Main Menu\Dial Plan\Phone/Hunt Group/Destination Settings, we can find Phone/Hunt Group/Dest. Setting Menu. We are doing VIP telephone address table management. We can add (delete, find or list) desired telephone number mapping to hunt group at this menu. Telephone Number Hunt Group ID Telephone number to match. This is only part of the total dialed string. For each hunt group ID, you need to assign it a unique identifier between 0 and 99. Min.
SIP Voice Gateway User’s Manual To delete / find a Telephone, select the option and telephone, you can key in the phone number to find or delete. The right bottom screen will show the result.
VIP User’s Manual 4.1.1.2 Hunt Group Please select Main Menu\Dial Plan\Phone/Hunt Group/Destination Settings, we can find Phone/Hunt Group/Dest. Setting Menu. We are doing VIP hunt group table management. We can add (delete, find or list) desired hunt group ID mapping to destination ID at this menu. If you want to make the port calls to the secondary receiver, you can click one “More Destinations” you can then add the second, third receiver if the desired port/phone is busy.
SIP Voice Gateway User’s Manual 4.1.1.3 Destination IP/ Destination Channel Please select Main Menu\Dial Plan\Phone/Hunt Group/Destination Settings, we can find Phone/Hunt Group/Dest. Setting Menu. We are doing VIP destination table management. One is Remote Destination IP, one is Remote Host Name and the other is Local Destination Channel.
VIP User’s Manual We can add (delete, find or list) desired destination ID mapping to Remote Destination IP, Domain Name or Local Destination Channel at this menu. Please back to Dial Plan Menu. 4.1.1.
SIP Voice Gateway User’s Manual This Common Parameter Settings is the same as previous ATPM system parameters description. . 4.1.2 Clear DialPlan Please select Main Menu\Dial Plan\Clear All Dial Plan Settings Clear All Dial Plan Settings will clear all the settings you made before. However, the 'Clear All' is only temporary if you do not store to the Flash Memory afterwards.
VIP User’s Manual 4.1.3 Restore DialPlan Please select Main Menu\Dial Plan\Restore All Dial Plan Settings Retrieve all dial plan settings from the flash memory. All temporary settings will be cleared. 4.1.
SIP Voice Gateway User’s Manual 4.2 View System Configurations Please select Main Menu\View System Config. View System Config. Function Briefings. Six options available 1.Firmware Version Information, which shows the versions of each firmware component 2.Network Settings, which shows the IP-related settings, and the status of associated management tools 3.SIP Parameter Settings, which shows the SIP-related parameters associated with the gateway 4.
VIP User’s Manual SIP Addr Configuration: UDP ctl addr = 192.168.0.99/5060 RTP data addr = 192.168.0.99/2070 Domain name server = 168.95.192.1 Info switch is off nat_call is on auto_reg is off outboundproxy : None 4.2.3 Voice Coder Type Please select Main Menu\View System Config.\Coder Type The Voice Coder For Each Line Module: Voice coder is G.723 for Line Module 1. 4.2.4 Voice Coder Information Please select Main Menu\View System Config.
SIP Voice Gateway User’s Manual 4.2.5 Channel Parameters Please select Main Menu\View System Config.\Channel Parameters This command can show the desired channel setting of VIP.
VIP User’s Manual 4.2.6 Network Connection Please select Main Menu\View System Config\Network Connection This command can display the type of connection currently enabled in VIP. 4.2.6.1 DHCP Settings Display current DHCP status in VIP Command Line Interface reference: net set dhcp net set dhcp command configures VIP to be DHCP client in order to obtain TCP/IP related parameters from ISP while VIP is deployed in DHCP environment.
SIP Voice Gateway User’s Manual 4.2.6.2 PPPoE Settings Display current PPPoE status in VIP Command Line Interface reference: net set pppoe The net set pppoe command configures PPPoE related parameters while VIP is deployed in PPPoE environment.
VIP User’s Manual password fix_ip PPPoE connection password provided by ISP Fixed IP address provided by ISP If PPPoE client is enabled/disabled, VIP has to be rebooted to make the PPPoE service started/stopped.
SIP Voice Gateway User’s Manual 4.2.6.
VIP User’s Manual DDNS service can help users to find each other in dynamic/static IP environment, and enable two VIPs call each other with registered host names. To be fully functional, DNS server MUST be added into SIP configuration while DDNS service is enabled. DDNS clients supported in VIP are www.dyndns.org and www.dtdns.com currently. If VIP DDNS client is enabled, users MUST register a DDNS name from the sites listed above before proceeding any further.
SIP Voice Gateway User’s Manual System Config. Settings Function Briefings 1. IP Settings, which allows one to set the gateway's IP address, its subnet mask, and its Default Gateway IP address. 2. SIP Parameter Settings, which allows one to set the SIP parameters, such as communication ports, SIP registration settings, outbound proxy server settings …… etc. 3.
VIP User’s Manual 4.3.1 IP Settings Please select Main Menu\Configure System Settings\IP Settings This screen can setup your VIP IP Address, Subnet Mask and Default IP Gateway Address. These values will be valid after VIP reboot. 4.3.2 SIP Parameters Please select Main Menu\Configure System Settings\SIP Parameter Settings There are SIP Configuration Settings, Registration Server Settings, Outbound Proxy Sever configurations, Domain name server configurations, and Other settings.. 4.3.2.
SIP Voice Gateway User’s Manual 4.3.2.
VIP User’s Manual 4.3.2.2 SIP Outbound Proxy Server Settings Please select Main Menu\Configure System Settings\SIP Parameter Settings\SIP Outbound Proxy Server Settings 4.3.2.
SIP Voice Gateway User’s Manual 4.3.2.
VIP User’s Manual Chapter 5 Troubleshooting Tips This section provides solutions for problems you may possibly encounter while installing and connecting your Internet Telephony Gateway. Power (PWR) LED is not illuminate 1. 2. 3. 4. 5. Check the power adapter connection. If the power adapter or power cord is connected to the gateway, check that the cord is securely plugged into the power socket on the rear of the console.
SIP Voice Gateway User’s Manual Chapter 6 Command Line Interface VIP has a built-in command line interpreter and provides users a Command Line Interface (CLI). You can configure VIP by entering commands from the CLI. You can access the CLI from a VT-100 terminal or terminal emulator connected to the RS-232 port on the front panel or through a Telnet session. 6.
VIP User’s Manual Task Prompt Type From the remote host, enter the telnet command None followed by the IP address of VIP you want to access. telnet ip_addr When VIP prompts “Login:”, enter the user name Login: “administrator” administrator When VIP prompts “Password:”, enter the pass- Password: word.
SIP Voice Gateway User’s Manual 6.6 Command Reference The following table list the CLI command in alphabetic order.
VIP User’s Manual 6.7 Utility Commands clrscr The clrscr command to clear the screen Syntax Description This command has no arguments or keywords download Use the download command to enter download mode for reading code image from a TFTP server and program it to flash memory. Refer to 0 for detailed information on how to upgrade the system software. Syntax Description This command has no arguments or keywords Note This command in available from serial interface.
SIP Voice Gateway User’s Manual 6.8 Network Commands net reset Use the net reset command to reset VIP. The CLI will prompt you to confirm the command before resetting VIP. Syntax Description This command has no arguments or keywords net set gateway ip_addr Use the net set gateway command to assign a default gateway (router) for VIP. The default gateway routes packet data outside or your IP subnet. Syntax description ip_addr The IP address of the default gateway. IP address of 0.0.0.
VIP User’s Manual The new IP address will not take effect until VIP is reset. net set ip_preced ip_preced VIP allows you to set the 8-bit Service Type field in the IP header for all the voice packets it sends out. The Service Type field is broken down into five subfields, among which four subfileds are user configurable. This command is used to set these subfields. net set ip_preced ip_preced [d] [t] [r] Syntax description ip_preced The 3-bit PRECEDENCE subfiled ranging from 0 through 7.
SIP Voice Gateway User’s Manual auto Enable the 10/100 Mbps auto-negoriation capablity. net set user_pw password password Use the net set user_pw command to change the password for Telnet user. Syntax description The new password. The password must be equal to or less than 7 password alphanumeric characters. It must be identically typed twice for VIP to be certain about the new password. net show The net show command displays all the network settings.
VIP User’s Manual HTTP server = Telnet server = enabled enabled ****************************************************** ITG> net show hwstat The net show hwstat command displays the hardware configuration of VIP.
SIP Voice Gateway User’s Manual on Turn on DHCP client off Turn off DHCP client net set dyndns DDNS service can help users to find each other in dynamic/static IP environment, and enable two VIPs call each other with registered host names. To be fully functional, DNS server MUST be added into SIP configuration while DDNS service is enabled. DDNS clients supported in VIP are www.dyndns.org and www.dtdns.com currently.
VIP User’s Manual 6.9 Configuration Management Commands The configuration management commands allow the user to set values for system configuration parameters. In addition, it provides mechanisms to allow a user to control when new parameter values are put in use. The CLI maintains three areas where the parameters are stored: Ÿ Temporary Ÿ Active Ÿ Non-volatile Storage (NVS) When a set command is entered and processed, it changes the parameter value in the Temporary area.
SIP Voice Gateway User’s Manual show sip The show SIP command displays the settings of the parameter that are related to SIP signaling protocol. Syntax Description This command has no arguments or keywords Example The following example shows how to display the SIP parameters: ITG>show sip SIP Addr Configuration: UDP ctl addr = 192.168.0.99/5060 RTP data addr = 192.168.0.99/2070 Domain name server = 168.95.192.
VIP User’s Manual show sip nat_call - Displays nat_call switch show sip outboundproxy - Displays the outbound proxy set sip reg add - used to add registration information set sip reg add [reg_num] [expires] [#registrar] [ip] [port] {name | 0} {passwd | 0} {ip port …} Syntax description reg_num the phone number to be registered expires how long the reg_num is to re-register #registrar the number of registrar ip IP of the registrar port port of the registrar name [the name for authentication | 0
SIP Voice Gateway User’s Manual proxy svr nwa set sip actreg - used to send out the registration set sip actreg set sip dns_ip - used to set the domain name server. The IP domain should be in numerical format set sip dns_ip [ip] Syntax description ip
VIP User’s Manual 6.10 Voice Coding Profile Configuration Commands Coding profile is used to store coding parameters for voice and fax coding p that can be used by telephony port on VIP. VIP has built-in coding profiles, each having a unique profile ID and parameters for specific voice, fax or modem coder. Among these coding profiles, there are five may be used for voice or fax applications. The following table summarizes coding profiles available for voice and fax applications.
SIP Voice Gateway User’s Manual set coding profile_id cp_tone_detect {on | off} This command is used to specify a secondary level of control of call progress tone detection. If the call progress detection control for a telephony port is set to "As per coding profile" (refer to command “set port port cp_tone_det_ctrl”), this parameter determines if detection is to be enabled or not. Syntax description on Enable call progress tone detection. off Disable call progress tone detection.
VIP User’s Manual on Enable adaptive playback. off Disable adaptive playback. set coding profile_id dtmf_relay {on | off} VIP supports DTMF Relay, in which DTMF tones are detected during voice processing, encoded into SIP-UserInformation packets and conveyed to the remote VIP via the SIP call control band. This command is used to enable or disable the DTMF Relay feature.
SIP Voice Gateway User’s Manual set coding profile_id nom_delay Syntax description Delay Value in milliseconds. set coding profile_id vad {on | off} This command is used to enable/disable the Voice Activity Detector (VAD) for a coding profile. Syntax description On Enable VAD. Off Disable VAD. set coding profile_id vad_thresh This command is used to set threshold level for the VAD for a coding profile. Syntax description threshold Value in dBm, ranging from –20 to +10.
VIP User’s Manual Size of the Voice Information Field (VIF), in bits, for a voice coder are related to the coding type and the rate the voice coder samples a voice frame (the packet time), as shown in the table above. VIF sizes of a coder of values other than those shown in the table are not valid. 6.11 Dial Plan Management Commands Among the command sets supported by the CLI, the dial plan management commands are the most sophisticated.
SIP Voice Gateway User’s Manual Database Update Control Commands atpm done The atpm done command ends the atpm table update session and re-enables the address translation. Syntax description This command has no arguments or keywords atpm erase The atpm erase command erases the dial plan database from the non-volatile memory. Syntax description This command has no arguments or keywords atpm purge {all|addr|dest|hunt} Use the atpm purge command to delete all entries from the atpm tables.
VIP User’s Manual atpm store [erase] The atpm store command store all atpm tables into non-volatile memory. Syntax description erase (Optional) Erase the non-volatile before storing the dial plan database. This option is not recommended except the very first time you use the atpm store command. Hunt Group Table Management Commands atpm hadd hunt_group_id {1|2} dest_id [desi_id2] … Use the atpm hadd command to add an entry into the atpm hunt group table. Syntax description hunt_group_id Hunt group ID.
SIP Voice Gateway User’s Manual Syntax description hunt_group_id ID of the hunt group to be displayed. atpm hlist The atpm hlist display all entries in the hunt group table.
VIP User’s Manual atpm adel tel# The atpm adel command deletes an entry from the atpm address table. Syntax description tel# Number of a previously added entry to be deleted from the atpm address table. atpm afind tel# The atpm afind finds and display an entry in the address table. Syntax description tel# Number of a previously added entry in the atpm table to be displayed. atpm alist The atpm alist displays all entries in the address table.
SIP Voice Gateway User’s Manual ITG>atpm slist System Info: Total dial time = 30000ms, First digit wait = 10000ms, Interdigit wait = 5000ms, Dial term digit = None OK ITG> atpm sys dial_time 1st_digit_wait inter_digit_wait [dial_term_digit] Use the atpm sys command to set the time constraints for collection of dial digits. Syntax description The maximum time, in millisecond, allowed for entry of the entire string of dial digits. At expiration, ATPM starts address lookup.
VIP User’s Manual tel set pcm_gain_level {1|2|3|4|5} The FXO ports might be connected to central office switch or PBX via local loop which may of as long as several miles. For compensating signal distortion in the local loop, VIP’s PCM codec is designed in such a way that users might adjust it gain level before transmitting analog signal to the local loop. The tel set pcm_gain_level command is used to set the gain level for the PCM codec for compensating signal loss in the local loop.
VIP User’s Manual Chapter 7 Upgrading and resetting VIP VIP-450 is able to have system functionality enhancement via software upgrade. This must be operated in upgrade mode. In firmware upgrade mode, limited commands allow users to read new revision codes from a remote TFTP server and write into the built-in flash non-volatile storage. To enter download mode, either Telnet or Console (RS-232) connection can take the job, and a TFTP server is required by VIP to complete firmware upgrade process. 7.
VIP User’s Manual TFTP server configuration 1. Execute TFTP server program, assign firmware file location, and save the path if necessary. (In this sample datagram, the file is assigned in c:\) (This part might vary on different kind of TFTP server.) 2. Allocate VIP firmware file in the directory, and apply the modification (if required). Note: TCP port 69 is required for TFTP access.
SIP Voice Gateway User’s Manual ITG>download ============================== WARNING ============================== * Entering download mode will hang up all telephone connections * * and all the configuration settings will lose. * * Be certain all the configuration settings have been saved. * ======================================================================= Do you want to enter download mode now (y/n)? [n] y Boot loader V4.12 Loading TFTP loader.....................
VIP User’s Manual Console session a) Connect VIP through the 9-pin RS232 female console (No password required) Under ITG> prompt, insert command: download to enter VIP firmware upgrade mode. b) Insert command: “start” and answer questions on screen to proceed firmware upgrade. c) When VIP prompts downloading firmware file into EEPROM, insert “y” to continue.
SIP Voice Gateway User’s Manual Trouble Shooting Tips If following error (TFTP timeout error) occurs: ** Internet Telephony Gateway TFTP Loader Ver 4.10 ** EITGLoader>start IP address of the TFTP server? [192.168.0.7] File name? xyz123.imz Starting download file: xyz123.imz TFTP device open failed. - TFTP server timeout while waiting for a response from the client. Download another file (y/n)? [n] Possibility: a) Network connection is not correctly configured è check if cable is securely connected.
VIP User’s Manual 7.2 CLI Commands in Download Mode Under download mode, the CLI supports the following commands: Command Description help Display help screen quit Terminate download mode, switch to normal operation mode. set Change IP parameter start Start downloading code from TFTP server The following section describes each of the commands. help The help command lists the top-level commands. quit The quit command is used to terminate the download mode and return to normal operation mode.
SIP Voice Gateway User’s Manual set mask ip_mask Use the set mask command to set the IP subnet mask for VIP. Syntax description ip_mask The subnet mask of your network. Note The new setting will not take effect until VIP is reset. start Use the start command to start downloading code from TFTP server. VIP will prompt you for the IP address of the TFTP server and the file to download. 7.
VIP User’s Manual A sample is attached below for reference. ITG>config erase The system configuration data will be erased from non-volatile storage permanently. Are you sure to erase it (y/n)? [n] y System configuration records erased from flash ITG>net reset ============================== WARNING ============================== * Restarting the system will hang up all telephone connections * * and all the configuration settings will lose. * * Be certain all the configuration settings have been saved.
SIP Voice Gateway User’s Manual Dialplan configuration default parameters: a) Log on VIP via telnet or console connection. b) At the ITG prompt, insert following commands: ITG>atpm erase ITG>net reset (Answer ”y” to reboot machine.) After rebooting, logon VIP. At the ITG> prompt, insert: atpm store to restore Dialplan default value into VIP. A sample is attached below for reference. ITG>atpm erase The dial plan will be erased from non-volatile storage permanently.
VIP User’s Manual Appendix A Technical Specifications A.1 VIP Technical Specifications VIP-450: 2 ports loop start FXO, 2 ports loop start FXS Telephony Interface Module support VIP-050: 4 ports loop start FXO, 4 ports loop start FXS (Up to two modules per unit) Network Interface Ports 1 10/100Base-T, auto sensing, RJ45 Voice codec support G.711 PCM 64kbps (A-law and μ-law) G.723.1A ACELP/M-MLQ (5.3, 6.3kbps) G.729AB CS-ACELP (8kbps) Fax ITU-T V.21, V.27ter, V.29, V.33 and V.
VIP User’s Manual EMI FCC Part 15 Class A EN55022 Class A (CISPR-22 Class A) VCCI Class A CE Safety UL 1950 CE Compliances VIP-450: Desktop Mounting A.2 VIP-000: Desktop or 19” rack mounting Console Port The console port uses a DB-9 RS-232 connector. The supplied straight-through RS-232 cable connects the console port of VIP to a console PC or terminal. Pinout for the port is described in the following table. A.
SIP Voice Gateway User’s Manual A.4 6 TxD- 7 Not connected 8 Not connected FXO Port Pin Assignments The FXO Telephony Interface Module has 4 RJ11C/W modular jacks. The following diagram and table show the assignments of the pin for the RJ11 port. A.5 RJ-11 pin Signal 1 Not connected 2 Tip 3 Ring 4 Not connected 1 2 3 4 FXS Port Pin Assignments The FXS Telephony Interface Module has 4 RJ11C/W modular jacks.
VIP User’s Manual A.6 FXO Card Technical Specifications Signaling: Loop Start / DTMF No. of channels: 4 Interface Connectors: 4 RJ-11 2-pin modular jacks. Line Impedance : 600 W 900 W Insertion Loss: 2 dB nominal. Frequency Response: 300Hz ~ 3400Hz +/- 2dB w.r.t. 1004Hz. Return Loss: ³ 18 dB Input Level adjustment: -6 dB to +6 dB Output Attenuation: 0 dB to 13 dB Longitudinal Balance: ³ 45 dB A.7 FXS Card Technical Specifications Signaling: Loop Start / DTMF No.
VIP User’s Manual Appendix B CLI Commands B.
VIP User’s Manual net reset Reset the system net set gateway Set default gateway’s IP address net set http Turn on/off HTTP server net set ip Set IP address net set ip_preced Set IP precedence bits net set mask Set IP subnet mask net set speed Select Ethernet link speed net set user_pw Set password net show Display IP parameters net show hwstat Display hardware status ping Send ICMP echo request to another host show sip Display SIP parameter settings show version Show software vers
VIP User’s Manual Appendix C Factory Default Settings The following table lists the settings of certain parameters before VIP is shipped. Parameter Default Setting Network IP address IP subnet mask Default gateway IP precedence Ethernet link speed User ID for HTTP browser and Telnet client login Password for HTTP browser and Telnet access login User name for Telnet session in download mode Password for Telnet session in download mode HTTP server Telnet server 192.168.0.1 255.255.255.0 0.0.0.
