SIP IP Phone VIP-154T/VIP-154PT/VIP-154NT User’s manual 1
Copyright Copyright (C) 2006 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Revision User’s Manual for PLANET SIP IP Phone: Model: VIP-154T/VIP-154PT/VIP-154NT Rev: 1.0 (2006, October) Part No.
TABLE OF CONTENTS Chapter 1 ................................................................................................ 6 Introduction............................................................................................ 6 Overview............................................................................................................................6 Package Content ...............................................................................................................
Auto Configuration...................................................................................................36 PTT Settings (For VIP-154NT) ................................................................................37 Country Settings .......................................................................................................37 System Authority ......................................................................................................37 Save & Reboot......................
1 Chapter 1 Introduction Overview Meeting the next-generation Internet telephony service demands, PLANET Technology provides feature-rich, toll-quality Internet telephony service solutions. The built-in PSTN interface provides user more convenience between IP Phone and PSTN call selections. －VIP-154NT. With 802.3af Power over Ethernet (PoE) IP Phone －VIP-154PT. And the VIP-154T is the cost-effective SIP IP Phone; the VIP-154 series are SIP 2.0 (RFC3261) compliant with SIP digest authentication supports.
Product Features • Built-in PSTN (VIP-154NT) The built-in PSTN interface provides user more convenience between IP Phone and PSTN call selections easily • Simple Installation and administration Configuration of the IP Phone can be performed in minutes via the LCD menu keypad, telnet, or web interfaces. Using the built-in LCD display, the IP Phone offers user-friendly configuration guidelines, machine operation status, call status displays, and incoming call identification.
VoIP Features • SIP 2.0 (RFC3261) compliant • Peer-to-Peer / SIP proxy calls • Voice codec support: G.711, G.723.1, G.726, G.729A, G.729B • Voice processing: Voice Active Detection, DTMF detection/ generation, G.168 echo cancellation (16mSec.
Physical Details The following figure illustrates the front/rear panel of IP Phone.
1 RESET Reset to the factory default setting 2 12V DC 12V DC Power input outlet 3 PC RJ-45 connector, to maintain the existing network structure, connected directly to the PC through straight CAT-5 cable RJ-45 connector, for Internet access, connected directly to Switch/Hub through straight CAT-5 cable. 4 LAN The LAN interface also can be connected with 802.3af PoE switch or injector for power supply (VIP-154PT) RJ-11 connector, connected directly to the PSTN analog line.
Front View and Keypad function Keypad Description 1 LCD Display Speed Dial 2 M1~M4 3 MENU 4 Vol +/↑ Menu and all status shall be displayed for users. To make a speed dial call by pressing the speed dial key M1 ~ M4. To bring out the menu selection while IP Phone is in idle state. To increase the volume of voice when at off-hooked state. To page up menu when at configuration mode. To decrease the volume of voice when at off-hooked state. 5 Vol - /↓ To page down menu when at configuration mode.
Enter the phone book selection. 7 Phone Book 8 MESSAGE 9 TRANSFER 10 CONF Press this button can make 3-way conference function. 11 FWD To carry out forward function. Press this button can enter the voicemail service. To transfer an active call (incoming call answered or outgoing call accepted) to another devices. Press to delete digits when at configuration mode or input 12 DEL/MUTE phone numbers. Press to mute sounds when at talk mode.
2 Chapter 2 Preparations & Installation Physical Installation Requirement This chapter illustrates basic installation of IP Phone • Network cables. Use standard 10/100Base-TX network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs. For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem Administration Interface PLANET IP Phone provides GUI (Web based, Graphical User Interface) for machine management and administration.
IP Phone will prompt for logon username/password, please enter: root / null (not password) to continue machine administration. LNote In order to connect machine for administration, please locate your PC in the same network segment (192.168.0.x) of IP Phone. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations.
LAN mask of IP Phone Subnet Mask Default: 255.255.255.0 Default Gateway Gateway of IP Phone Default: 192.168.0.254 After confirming the modification you’ve done. Please click on the Submit button to apply settings and browse to “Save & Reboot” menu to reboot the machine to make the settings effective. Connection Type Data required. In most circumstances, it is no need to configure the DHCP Fixed IP settings. DHCP clinet The ISP will assign IP Address, and related information.
Initialize IP Phone through LCD phone menus STEP 1: Power on machine, the LCD screen displays flashing greeting as below: Starting… STEP 2: Wait for 10 seconds, the main LCD screen shall be shown as below, and when the Internet access is available, the IP phone will connect to the SNTP server. The current time will be displayed on the LCD.
3 Phone setting 3.1 3.2 3.3 3.4 3.5 4 Network 5 SIP Settings Call forward 3.1.1 All Forward 3.1.1.1 Activation: To Enabled/Disabled this function. 3.1.1.2 Number: Forward to a Speed Dial Number. 3.1.2 Busy Forward 3.1.2.1 Activation: To Enabled/Disabled this function. 3.1.2.2 Number: Forward to a Speed Dial Number. 3.1.3 No Answer Forward 3.1.3.1 Activation: To Enabled/Disabled this function. 3.1.3.2 Number: Forward to a Speed Dial Number. 3.1.
6 NAT Transversal 7 Administrator 5.1.2 Service domain / Second realm / Third realm 5.1.2.1 First / Second / Third realm 5.1.2.1.1 Activation 5.1.2.1.2 User name 5.1.2.1.3 Display name 5.1.2.1.4 Register name 5.1.2.1.5 Register password 5.1.2.1.6 Proxy server 5.1.2.1.7 Domain server 5.1.2.1.8 Outbound proxy 5.1.3 Codec 5.1.3.1 Codec type 5.1.3.1.1 G.711 uLaw 5.1.3.1.2 G.711 aLaw 5.1.3.1.3 G.723 5.1.3.1.4 G.729 5.1.3.1.5 G.726-16 5.1.3.1.6 G.726-24 5.1.3.1.7 G.726-32 5.1.3.1.8 G.726-40 5.1.3.
3 Chapter 3 Network Service Configurations Configuringnd monitoring your IP Phone from web browser The IP Phone integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard, web browser, you can configure and check machine status from anywhere around the world. Overview on the web interface of IP Phone With web graphical user interface, you may have: More comprehensive setting feels than traditional command line interface.
When users login the web page, users can see the IP Phone system information like firmware version, company…etc in this main page.
4 Chapter 4 IP Phone Configurations Phone Book settings IP Phone can set up 140 records of Phone Book. User can make calls via Phone Book feature of IP Phone. Field Phone Book Page Phone Name Description The default is Page 1. It can select Page1 ~ Page 14 to look round Phone Book records. The record number from 0 ~ 139, it can set up 140 records in total.
numerals. Fill in the outgoing number (Line Number) or IP URL address. To select this record. Select If you need to add a phone number into the Phone Book list, you need to input the position, the name, and the phone number (by URL type). When you finished a new phone list, just click the “Add Phone” button. If you want to delete a phone number, you can select the phone number you want to delete then click “Delete Selected” button.
STEP 3: Selecting the recorder you want to dial and press OK button. It sill show the detail information as below: 202 192.168.1.2:5062 STEP 4: Pick up the telephone handset or press Handfree button to dial to this telephone. IP Dialing... 1 192.168.1.2:5062 Speed Dial settings In Speed Dial setting function you can add/delete Speed Dial number. You can input maximum 10 entries speed dial list. You can setup the Speed Dial number.
Call Forward This page defines Call Forward function. You can setup the phone number you want to forward in this page. There are three type of Forward mode. You can choose All Forward, Busy Forward, and No Answer Forward by click the icon: All Forward: All incoming call will forward to the number you chosen. You can input the name and the phone number in URL field. If you select this function, then all the incoming call will direct forward to the speed dial number you choose.
Call Forward function for VIP-154T/VIP-154PT Call Forward to PSTN (VIP-154NT): VIP-154NT not only supports Call Forward to IP calls, but also can forward the calls to PSTN. You can choose the Call Forward type with PSTN, and then input the name and the PSTN number in URL/Number field.
SNTP settings This page defines the primary and second SNTP server IP address, to get the date/time information. Also you can base on your location to set the Time Zone, and how long need to synchronize again. When you finished the setting, please click the Submit button. Volume Setting This page defines the Handset Volume, Ringer Volume, and the Handset Gain. When you finished the setting, please click the Submit button. Handset Volume is to set the volume for you can hear from the handset.
Beside the above settings, VIP-154NT also can set the volume of PSTN. PSTN-Out Volume is to set the volume for you can hear from the PSTN line. PSTN-In Gain is to set the volume send out to the other PSTN side’s haneset. Volume Settings for VIP-154NT Ringer Setting This page defines the user can set the tinkle of bells when someone ring your IP Phone. If want to set ringer, it need to enable Ringer function and select the Ringer Type you wanted. There are four Ringer Types can be chosen.
Block Setting This page defines the Block Setting to keep the phone slience. You can choose Always Block or Block a period. Always Block: All incoming call will be blocked until disable this feature. Block Period: Set a time period and the phone will be blocked during the time period. If the “From” time is large than the “To” time, the Block time will from Day 1 to Day 2. When you finished the setting, please click the Submit button.
Dial Plan Settings This page defines the Dial Plan Setting function. This function is when you input the phone number by the keypad but you don’t need to press “#”. After time out the system will dial directly. Symbol Explan: Digits Description X or X 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 + or Replace rule: If replace prefix code function is ON and prefix number is matched with rule then 005 will replace prefix. Auto Dial Time: Stop dialing after seconds then send dial number out.
Digits Description 0 Iignore auto prefix if first digit is ‘0’ 1 Ignore auto prefix if first digit is ‘1’ xxxx dial numbers are 4 digits ignore auto prefix Xxxxx dial numbers are 5 digits ignore auto prefix When you finished the setting, please click the Submit button.
Voice Mail Settings This page defines the voice mail key function. When device register to IP PBX and it support Voice Mail System. It can set up the voice mail number in advanced, and press the “MESSAGE” button from keypad. It will enter for voice mail system. DDNS Settings This page defines the DDNS setting in this page. You need to have the DDNS account and input the informations properly. You can have a DDNS account with a public IP address then others can call you via the DDNS account.
Service Domain Settings This router comes with the built-in firewall based on the advanced technology of Stateful Packet In Service Domain Function you need to input the account and the related informations in this page, please refer to your ISP provider. You can register three SIP account in the Phon. You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts.
Port Settings This page defines the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you finished the setting, please click the Submit button. Codec Settings This page defines the Codec priority, RTP packet length, and VAD function in this page. You need to follow the ISP suggestion to setup these items. When you finished the setting, please click the Submit button.
Codec ID Setting This page defines the Codec ID. Sometimes 2 VoIP devices with different Codec ID will cause the interopability issue. If you are talking with others got some problems, you may ask the other one what kind of Codec ID he use then you can change your Codec ID. When you finished the setting, please click the Submit button. DTMF Settings This page defines the DTMF parameters. Yyou can setup the RFC-2833, Inband and Send DTMF SIP Info in this page.
RPort Settings This page defines the RPort Enable/Disable in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button. Other Settings This page defines the Hold by RFC, Voice/SIP QoS and SIP expire time in this page. To change these settings please following your ISP information. When you finished the setting, please click the Submit button. The QoS setting is to set the voice packets’ priority.
Auto Configuration This page defines the Auto Configuration (Auto Provision) setting. IP Phone supports TFTP, FTP, HTTP and IP PBX auto configuration function in total. In IP PBX auto configuration setting you need to check with your service provider if they have provided this function. Usually this function will be bounden with an IP PBX to use in the office.
PTT Settings (For VIP-154NT) This page defines the PTT settings. When VIP-154NT connected to different country’s PSTN Line, you have to set the country’s setting to meet the requirement. When you finished the setting, please click the Submit button. Country Settings This page defines the ICMP echo Enable/Disable. This function can disable echo when someone ping this device, it can avoid haker try to attack the device. When you finished the setting, please click the Submit button.
Save & Reboot In Save & Reboot you can save the changes you have done. If you want to use new setting in the IP Phone, you have to click the Save button. After you click the Save button, the IP Phone will automatically restart and the new setting will effect. Firmware Upgrade In Firmware Upgrade function you can update new firmware via HTTP in this page. You can ugrade the firmware by the following steps: Select the firmware code type, AP or DSP code.
Firmware Upgrade methods: Please find the firmware of IP Phone, and be sure to check the firmware upgrade steps to load the firmware into machine properly for revolutions. a) Log in IP Phone via Microsoft Internet explorer web browser, and insert http://IP Phone IP address/update.htm in the address bar. b) Select update "All ROM", and browse to the firmware location. c) Please find the firmware (decompress and find the *.
Appendix A Voice communications There are several ways to make calls to desired destination in IP Phone. In this section, we’ll lead you step by step to establish your first voice communication via keypad and web browsers operations. Case 1: VIP-154T to VIP-154T connection via IP address Assume there are two VIP-154T’s in the network the IP address are 192.168.0.1, 192.168.0.2 192.168.0.2 192.168.0.
Case 2: Voice communication via SIP proxy server _SIP-50 SIP-50 IP Address: 192.168.0.50 VIP-154T IP Address: 192.168.0.1 Line Number: 1001 VIP-154T IP Address: 192.168.0.2 Line Number: 2002 Machine configuration on the VIP-154T: STEP 1: Log in SIP-50 and create two testing accounts/password: 1001/123 (for VIP-154T A), and 1002/123(for VIP-154T B) for the voice calls. STEP 2: Please log in VIP-154T A via web browser, browse to the SIP setting menu and select the Domain Service config menu.
STEP 3: Repeat the same configuration steps on VIP-154T B, and check the machine registration status, make sure the registrations are completed.
If you’d like to enable auto-config for IP extension features in IPX-2000, please be sure to setup the DHCP option code and the value information. In most case, insert the optional code 151 and the value=http://192.168.0.50/tftpboot/ Note: the 192.168.0.50 is the IP address of IPX-2000 STEP 2: Please browse to the Device menu and create new device for the auto configuration.
Machine configuration on the VIP-154T: STEP 5: Please log in VIP-154T A via web browser, browse to the Advanced Settings menu. In the setting page, please browse to the Auto-config page, and select to IP-PBX choice of the Auto Configuration features for IP PBX system. STEP 6: After enabled the Auto-config feature, the VIP-154T A shall be able to obtain IP address and SIP extension information from IP PBX system IPX-2000 information.
Case 4: Call Forward Feature _Example 1 In the following samples, we’ll introduce the Call Forward Feature applications. In this example, there are three VIP-154T register to SIP-50 and VIP-154T_A had set Call Forward function to VIP-154T_B. (The detail registration settings of SIP-50 and VIP-154T please refer to the instruction of Case 3) Machine configuration on the VIP-154T: STEP 1: Please log in VIP-154T_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
STEP 2: After set up completed and reboot machine, the LCD screen will show below: 10-19 17:20 # Forward # After 2~3 seconds, the LCD screen will show below: 10-19 17:20 AF 2002 Test the scenario: VIP-154T_C pick up the telephone and dial the number 1001(VIP-154T_A), because VIP-154T_A had set up All Forward function to the number 2002(VIP-154T_B), so the number 2002(VIP-154T_B) will ring up then it pick up the telephone and communication with the number 3003(VIP-154T_C).
Machine configuration on the VIP-154NT: STEP 1: Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
Case 6: Call Forward Feature_Example 3 In this example, there are one VIP-154NT and two VIP-154T register to SIP-50. The VIP-154NT_A had set Call Forward function to number 2002 (VIP-154T_B). Machine configuration on the VIP-154NT: STEP 1: Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
STEP 2: After set up completed and reboot machine, the LCD screen will show below: 10-19 17:20 # Forward # After 2~3 seconds, the LCD screen will show below: 10-19 17:20 AF 2002 Test the scenario: PSTN Phone Number 11112222 pick up the telephone and dial the PSTN Phone Number 33334444(VIP-154NT_A), because VIP-154NT_A had set up All Forward function to the number 2002(VIP-154T_B), so the number 2002(VIP-154T_B) will ring up then it pick up the telephone and communication with the PSTN Phone Number 111122
Case 7: Call Forward Feature_Example 4 In this example, there are three VIP-154T and connect with Peer to Peer mode. VIP-154T_A had set Call Forward function to VIP-154T_B. Machine configuration on the VIP-154T: STEP 1: Please log in VIP-154T_A via web browser, browse to the Phone Settings menu and select the Call Forward config menu.
Test the scenario: VIP-154T_C pick up the telephone and dial the IP Address 192.168.0.1(VIP-154T_A), because VIP-154T_A had set up All Forward function to the IP Address 192.168.0.2(VIP-154T_B), so the IP Address 192.168.0.2 (VIP-154T_B) will ring up then it pick up the telephone and communication with the VIP-154T_C. Case 8: Auto Answer Feature_IP to PSTN In this example, there are one VIP-154NT and two VIP-154T and connect with Peer to Peer mode.
STEP 2: Please log in VIP-154NT_A via web browser, browse to the Phone Settings menu and select the Auto Answer config menu. In the setting page, please enable the Auto Answer and PIN Code Enabled function, then the sample configuration screen is shown below: Test the scenario: VIP-154T_C pick up the telephone and dial the IP Address 192.168.0.1(VIP-154NT_A), VIP-154NT will ring up but doesn’t answer the call. After 3 rings, the VIP-154T_C will hear the prompt sounds then input the password 123#.
Case 9: Auto Answer Feature_PSTN to IP In this example, there are one VIP-154NT and two VIP-154T and connect with Peer to Peer mode. The VIP-154NT_A had set Auto Answer function for forwarding to arbitrary telephone. If there have incoming PSTN calls and VIP-154NT_A doesn’t answer the incoming calls after specific time, the caller will hear prompt sounds to input the password and then dial out an arbitary IP telephone.
Test the scenario: The Phone Number 11112222 pick up the telephone and dial the PSTN Phone Number 33334444(VIP-154NT_A), VIP-154NT will ring up but doesn’t answer the call. After 3 rings, the Phone Number 11112222 will hear the prompt sounds then input the password 123#. The Phone Number 11112222 will hear the dial tone then input 0#. The IP address 192.168.0.2 (VIP-153T_B) will ring up then it pick up the telephone and communication with the Phone Number 11112222.
Appendix B VIP-154 Series Specifications Product Model Hardware LAN PC Telephone Interface SIP IP Phone VIP-154T SIP PoE IP Phone VIP-154PT SIP IP Phone with PSTN connectivity VIP-154NT 1 x 10/100Mbps RJ-45 port Power Over Ethernet 802.3af compliant at VIP-154PT 1 x 10/100Mbps RJ-45 port 1 x RJ-11 --PSTN connectivity at VIP-154NT 2 x 16 characters Full duplex hands free speaker phone LCD display Speaker Protocols and Standard Standard SIP 2.
