User's Manual
Table Of Contents
- 1 Overview
- 2 Appendix Table
- 3 Introduction to the User
- 4 Basic Function
- 5 Advance Function
- 6 Phone Settings
- 7 Web Configurations
- 8 Network >> Basic
- 8.1 Network >> Service Port
- 8.2 Network >> VPN
- 8.3 Network >> Advanced
- 8.4 Line >> SIP
- 8.5 Line >> SIP Hotspot
- 8.6 Line >> Dial Plan
- 8.7 Line >> Basic Settings
- 8.8 Phone settings >> Features
- 8.9 Phone settings >> Media Settings
- 8.10 Phone settings >> MCAST
- 8.11 Phone settings >> Action
- 8.12 Phone settings >> Time/Date
- 8.13 Phone settings >> Tone
- 8.14 Phone settings >> Advanced
- 8.15 Phonebook >> Contact
- 8.16 Phonebook >> Cloud phonebook
- 8.17 Phonebook >> Call List
- 8.18 Phonebook >> Web Dial
- 8.19 Phonebook >> Advanced
- 8.20 Call Log
- 8.21 Function Key >> Function Key
- 8.22 Function Key >> Softkey
- 8.23 Function Key >> Advanced
- 8.24 Application >> Manage Recording
- 8.25 Security >> Web Filter
- 8.26 Security >> Trust Certificates
- 8.27 Security >> Device Certificates
- 8.28 Security >> Firewall
- 8.29 Device Log >> Device Log
- 9 Trouble Shooting
107 / 122
Speakerphone Volume Set the hands-free volume to 1-9.
Headset Ring Volume Set the volume of the earphone ringtone to 1~9.
Headset Volume
Set the volume of the headset to 1~9.
Speakerphone Ring Volume Set the volume of hands-free ringtone to 1~9.
G.723.1 Bit Rate 5.3kb/s or 6.3kb/s is available.
DTMF Payload Type Enter the DTMF payload type, the value must be 96~127.
AMR Payload Type Set AMR load type, range 96~127.
Headset Mic Gain Set the earphone's radio volume gain to fit different models of earphones.
Opus playload type
Set Opus load type, range 96~127.
OPUS Sample Rate Set Opus sampling rate, including opus-nb (8KHz) and opus-wb (16KHz).
ILBC Payload Type Set the ILBC Payload Type, the value must be 96~127.
ILBC Payload Length Set the ILBC Payload Length
Enable MWI Tone
When there is a new voice message message, the phone will start a
special dial tone.
Enable VAD
Whether voice activity detection is enabled.
Onhook Time
Configure a minimum response time, which defaults to 200ms
EHS Type EHS headset is available after enabling.
RTP Control Protocol(RTCP) Settings
CNAME user Set CNAME user
CNAME host Set CNAME host
RTP Settings
RTP keep alive Hold the call and send the packet after 30s
Alert Info Ring Settings
Value Set the value to specify the ring type.
Ring Type Type1-Type9
8.10 Phone settings >> MCAST
This feature allows user to make some kind of broadcast call to people who are in multicast group. User can
configure a multicast DSS Key on the phone, which allows user to send a Real Time Transport Protocol (RTP)
stream to the pre-configured multicast address without involving SIP signaling. You can also configure the
phone to receive an RTP stream from pre-configured multicast listening address without involving SIP
signaling. You can specify up to 10 multicast listening addresses.
Table 25 - Multicast parameters
Parameters Description
Normal Call Priority Define the priority of the active call, 1 is the highest priority, 10 is the lowest.
Enable Page Priority The voice call in progress shall take precedence over all incoming paging calls.