User's Manual
Table Of Contents
- Chapter 1. Product Introduction
- Chapter 2. Hardware Interface & Installa
- Chapter 3. Introduction to the Phone Use
- Chapter 4. IP Phone Setup
- Chapter 5. Using the Phone
- 5.1 Making Phone Calls
- 5.2 Make/Receive Second Call
- 5.3 Join/Split Two Calls (3-way Local Co
- 5.4 Call Transfer
- 5.5 Using Phonebook
- 5.6 Add/Edit/Delete Contact
- 5.7 Add/Edit/Delete Group
- 5.8 Browse and Add/Remove Contacts in Gr
- 5.9 Using Cloud Phonebook
- 5.10 Open Cloud Phonebook
- 5.11 Call Logs
- 5.12 Voice Message
- 5.13 Do-Not-Disturb
- 5.14 Auto-Answering
- 5.15 Call Forward
- Chapter 6. Phone Settings
- Chapter 7. Web Portal
- 7.1 Web Portal Authentication
- 7.2 Web Call
- 7.3 SYSTEM (Information)
- 7.4 SYSTEM (Account)
- 7.5 SYSTEM (Configurations)
- 7.6 SYSTEM (Upgrade)
- 7.7 SYSTEM (Auto Provision)
- 7.8 SYSTEM (Tools)
- 7.9 NETWORK (Basic)
- 7.10 NETWORK (Advanced)
- 7.11 NETWORK (VPN)
- 7.12 LINES (SIP)
- 7.13 LINES (Dial Peer)
- 7.14 LINES (Dial Plan)
- 7.15 LINES (Global Settings)
- 7.16 PHONE (Features)
- 7.17 PHONE (Audio)
- 7.18 PHONE (MCAST)
- 7.19 PHONE (Time/Date)
- 7.20 PHONE (Advanced)
- 7.21 PHONEBOOK (Contacts)
- 7.22 PHONEBOOK (Cloud Phonebook)
- 7.23 PHONEBOOK (Blacklist)
- 7.24 PHONEBOOK (Advanced)
- 7.25 CALL LOGS
- 7.26 FUNCTION KEY
- 7.27 FUNCTION KEY (Softkey)
- Chapter 8. Advanced Features
- Chapter 9. Troubleshooting
- Appendix I - Icon Illustration
- Appendix II - Text Input from Keypad
- Appendix III - LED Definition
Parameters Description
Ring Type Set the ring tone type for the line.
Conference Type
Set the type of call conference; Local = set up call conference
by the device itself; maximum supports two remote parties,
Server = set up call conference by dialing to a conference
room on the server.
Server Conference Number
Set the conference room number when conference type is set
to be Server.
Transfer Timeout Set the timeout of call transfer process.
Enable Long Contact Allow more parameters in contact field per RFC 3840.
Enable Missed Call Log
If enabled, the phone will save missed calls into the call
history record.
Response Single Codec
If setting enabled, the device will use single codec in
response to an incoming call request.
Use Feature Code
When this setting is enabled, the features in this section will
not be handled by the device itself but by the server instead.
In order to control the enabling of the features, the device will
send feature code to the server by dialing the number
specified in each feature code field.
Enable DND Set the feature code to dial to the server.
Disable DND Set the feature code to dial to the server.
Unconditional Enable Call Forward Set the feature code to dial to the server.
Unconditional Disable Call Forward Set the feature code to dial to the server.
Enable Call Forward on Busy Set the feature code to dial to the server.
Disable Call Forward on Busy Set the feature code to dial to the server.
Enable Call Forward on No Answer Set the feature code to dial to the server.
Disable Call Forward on No Answer Set the feature code to dial to the server.
Enable Blocking Anonymous Call Set the feature code to dial to the server.
Disable Blocking Anonymous Call Set the feature code to dial to the server.
Specific Server Type
Set the line to collaborate with specific server type; this is to
be address more in “VIP-1120PT Administration Guide”.
Registration Expiration Set the SIP expiration interval.
Use VPN Set the line to use VPN restrict route.
Use STUN Set the line to use STUN for NAT traversal.
Convert URI Convert non digit and alphabet characters to %hh hex code.
DTMF Type Set the DTMF type to be used for the line.
DTMF SIP Info Mode Set the SIP Info mode to send ‘*’ and ‘#’ or ‘10’ and ‘11’.
66