User's Manual
Table Of Contents
- Chapter 1. Product Introduction
- Chapter 2. Hardware Interface & Installa
- Chapter 3. Introduction to the Phone Use
- Chapter 4. IP Phone Setup
- Chapter 5. Using the Phone
- 5.1 Making Phone Calls
- 5.2 Make/Receive Second Call
- 5.3 Join/Split Two Calls (3-way Local Co
- 5.4 Call Transfer
- 5.5 Using Phonebook
- 5.6 Add/Edit/Delete Contact
- 5.7 Add/Edit/Delete Group
- 5.8 Browse and Add/Remove Contacts in Gr
- 5.9 Using Cloud Phonebook
- 5.10 Open Cloud Phonebook
- 5.11 Call Logs
- 5.12 Voice Message
- 5.13 Do-Not-Disturb
- 5.14 Auto-Answering
- 5.15 Call Forward
- Chapter 6. Phone Settings
- Chapter 7. Web Portal
- 7.1 Web Portal Authentication
- 7.2 Web Call
- 7.3 SYSTEM (Information)
- 7.4 SYSTEM (Account)
- 7.5 SYSTEM (Configurations)
- 7.6 SYSTEM (Upgrade)
- 7.7 SYSTEM (Auto Provision)
- 7.8 SYSTEM (Tools)
- 7.9 NETWORK (Basic)
- 7.10 NETWORK (Advanced)
- 7.11 NETWORK (VPN)
- 7.12 LINES (SIP)
- 7.13 LINES (Dial Peer)
- 7.14 LINES (Dial Plan)
- 7.15 LINES (Global Settings)
- 7.16 PHONE (Features)
- 7.17 PHONE (Audio)
- 7.18 PHONE (MCAST)
- 7.19 PHONE (Time/Date)
- 7.20 PHONE (Advanced)
- 7.21 PHONEBOOK (Contacts)
- 7.22 PHONEBOOK (Cloud Phonebook)
- 7.23 PHONEBOOK (Blacklist)
- 7.24 PHONEBOOK (Advanced)
- 7.25 CALL LOGS
- 7.26 FUNCTION KEY
- 7.27 FUNCTION KEY (Softkey)
- Chapter 8. Advanced Features
- Chapter 9. Troubleshooting
- Appendix I - Icon Illustration
- Appendix II - Text Input from Keypad
- Appendix III - LED Definition
If user wishes to enable or disable DND on a specific line, user could change the DND mode in DND
configurations.
Press the soft-button [Menu] till you find the [Features] item.
Enter [Features] item till you find the [DND] item.
Enter [DND] item till you find [DND item.
Press the left/right navigation key to change the DND mode or DND state on specific line. When
done, press the [Save] button to save the changes.
User will see icon ‘SIP Do Not Disturb’ against the enabled line.
Figure 58 - Configure DND on Line
5.14 Auto-Answering
User may enable auto-answering feature on the device and any incoming call will be automatically
answered (not including call waiting). The auto-answering can be enabled on line basis.
When the device is in the default standby mode, if user wishes to enable or disable auto-answering on
a specific line or change the auto-answering delay time, user could change the auto-answering
configuration by adopting the following steps:
Press soft-button [Menu] till you find the [Features] item.
Enter [Features] item till you find the [Auto Answer] item.
Enter [Auto Answer] item to change the auto-answering configuration on a specific line
Press the left/right navigation button to select the auto-answering option. When done, press the
[Save] button to save the changes.
The default auto-answering delay is 5 seconds.
53