IP Phone VIP-101T CLI User’s Manual This document is a command-by-command description for the PLANET VIP-101T CLI administration mode.
PLANET VIP-101T CLI configuration Copyright Copyright (C) 2003 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
PLANET VIP-101T CLI configuration disappears when you turn your Ethernet Switch off and reappears when you turn it back on, there is interference being caused by the Ethernet Switch. You can try to correct the interference by one or more of the following measures: Reorient the receiving radio or TV antenna where this may be done safely. To the extent possible, relocate the radio, TV or other receiver away from the Switch.
PLANET VIP-101T CLI configuration Table of Contents Command Line Interface Configurations ......................................................................................1 1. [help] ......................................................................................................... 1 2. [quit] .......................................................................................................... 2 3. [reboot] ...................................................................................
PLANET VIP-101T CLI configuration d) –keypad ........................................................................................... 18 e) –idto ................................................................................................. 19 f) –eod .................................................................................................. 19 g) -h450................................................................................................ 19 13. [h323] ................................
PLANET VIP-101T CLI configuration b) –fstart ............................................................................................... 35 c) –tunnel ............................................................................................. 35 d) -h245fs ............................................................................................. 35 17. [bureau] ................................................................................................. 36 a) -print............................
PLANET VIP-101T CLI configuration Command Line Interface Configurations PLANET VIP-101T provides CLI (Command Line Interface) for more detail, powerful machine configurations. In most circumstances, it is not necessary to proceed configurations via telnet session, LCD panel menu, and web configuration in VIP-101T can cover most configurations to meet different applications on your side. VIP-101T Telnet User Interface allows you to specify (and change) a variety of system configuration parameters.
PLANET VIP-101T CLI configuration usr/config$ ? help help/man/? [command] quit reboot quit/exit/close reboot local machine flash clean configuration from flash rom commit ifaddr commit flash rom data internet address manipulation time show current time ping pbook test that a remote host is reachable Phonebook information and configuration pppoe PPPoE stack manipulation sysconf h323 system information manipulation H.
PLANET VIP-101T CLI configuration no committed data, reboot command will restart machine only. Syntax Description This command has no arguments or keywords. Default This command has no default value. Example usr/config$ reboot . Data modified, commit to flash rom?(y/n)y This may take a few seconds, please wait.... Commit to flash memory ok!. This may take a few seconds, please wait....
PLANET VIP-101T CLI configuration usr/config$ flash Flash memory information and configuration Usage: flash -clean Note: This command will clean the configuration stored in the flash and reboot it. M Note When download or receive firmware upgrade from your service provider, it is required to perform a “flash -clean” to activate new configuration in machine. , press to log in machine.. 5.
PLANET VIP-101T CLI configuration Example usr/config$ ifaddr LAN information and configuration Usage: ifaddr [-print]|[-dhcp used]|[-sntp mode [server]] ifaddr [-ip ipaddress] [-mask subnetmask] [-gate defaultgateway] [-cmcenter cmcenter] ifaddr [-dns index [dns server address]] -print Display LAN information and configuration. -ip -mask Specify ip phone ip address. Set Internet subnet mask. -gate Specify default gateway ip address -dhcp -sntp Set DHCP client service flag (On/Off).
PLANET VIP-101T CLI configuration -gate Specify IP address of default gateway Default IP address=192.168.0.1, Mask=255.255.255.0, Gateway=255.255.255.255 b) -dhcp When DHCP function enables (ifaddr –dhcp 1), VIP-101T will automatically search DHCP server after commit and reboot process. Syntax Description -dhcp enable/disable DHCP client service.
PLANET VIP-101T CLI configuration Syntax Description -dns 1 xxx.xxx.xxx.xxx Default 1 (DNS option turned on, IP= 168.95.1.1) 1. Please consult your network administrator or ISP for DNS related information to M Note have best performance in domain name resolution. 2. If you’d like to use domain name as calling destination, please refer to H.323 and Phone Book sessions for more configuration tips.
PLANET VIP-101T CLI configuration 7. [time] Command time is used to display current time information. This function is valid only when SNTP server is configured in VIP-101T’s SNTP function. usr/config$ time Current time is FRI JAN 23 18:08:00 2003 G Hint If time information cannot display properly, please check command: ifaddr -sntp for configuration tips. 8. [ping] Command ping can be used to verify network connection status Syntax Description ping xxx.xxx.xxx.
PLANET VIP-101T CLI configuration Example usr/config$ ping 192.168.0.254 PING 192.168.0.254: 56 data bytes 64 bytes from 192.168.0.254: icmp_seq=0. time=5. ms 64 bytes from 192.168.0.254: icmp_seq=1. time=0. ms 64 bytes from 192.168.0.254: icmp_seq=2. time=0. ms 64 bytes from 192.168.0.254: icmp_seq=3. time=0. ms ----192.168.0.254 PING Statistics---4 packets transmitted, 4 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/1/5 9.
PLANET VIP-101T CLI configuration Example usr/config$ pbook Phonebook information and configuration Usage: pbook [-print [start_record] [end_record]] pbook [-add [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-search [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-insert [index] [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-delete index] pbook [-modify [index] [ip ipaddress] [name Alias] [e164 phonenumber]] -print -add Display phonebook data. Add an record to phonebook.
PLANET VIP-101T CLI configuration a) –print Parameter print can be used to display phone book database information. You can display all data in phone book by adding –print parameter. Furthermore, you like to display a section of data, indication parameter 'start_record' and 'end_record' can be used (pbook –print “start index #” “end index #”). If parameter 'end_record' is omitted, only record 'start_record' will be display (pbook –print “start index #”).
PLANET VIP-101T CLI configuration This command has no default value. Example usr/config$ pbook -add name test3 ip 210.66.155.96 e164 6532 usr/config$ pbook -add name test4 ip planetvip.dyndns.org e164 3698 usr/config$ This may take a few seconds, please wait.... Commit to flash memory ok! G Hint Either IP or URL address can be used for calling destination.
PLANET VIP-101T CLI configuration Default This command has no default value. f) –modify Parameter modify can be used to modify entries in phone book database that has addressed to index number. The name, IP address and e164 number should be modified together in one modify command. Syntax Description –modify name X ip xxx.xxx.xxx.xxx” e164 X Default This command has no default value. G Hint When dialing, please press ” # ” after dialing E.
PLANET VIP-101T CLI configuration seen with this command. Syntax Description -print Display PPPoE device information. Default This command has no default value. Example usr/config$ pppoe -print PPPoE adapter information Device : Disable Status : Not initialized User name : pppoe Password : ***** b) –dev Parameter –dev can be used to enable or disable PPPoE function. Syntax Description -dev Enable(=1) or Disable(=0) PPPoE function in VIP-101T Default 0 PPPoE function in VIP-101T is turned off.
PLANET VIP-101T CLI configuration Syntax Description -close Disconnect current PPPoE connection. Default This command has no default value. e) –id This parameter can be used to configure PPPoE connection user name. Syntax Description -id User name for PPPoE connection. Default pppoe f) –pwd This parameter can be used to configure PPPoE connection password. Syntax Description -pwd Password for PPPoE connection. Default pppoe.
PLANET VIP-101T CLI configuration 1 (Reboot machine while there is unexpected PPPoE disconnection) 11. [ddns] command This function is for Dynamic Domain Name Server service. Once user register to one DDNS server, he can specify domain name for VIP-101T. When VIP-101T reboot, it will automatically update it’s IP address to DDNS server. 1. -print: display DDNS overall information and configuration. 2. –enable: to enable/disable DDNS function.(ddns –enable 0/1, 0 for disable and 1 for enable). 3.
PLANET VIP-101T CLI configuration 12.[sysconf] command This command displays the system information and configuration. System information and configuration Usage: sysconf [-plan digits] [-callalive flag] [-h450 flag] [-keypad type] [-idto time] [-eod type] sysconf -print -print Display system overall information and configuration. -plan Number of digits for dial plan. ( No or positive number 1 ~ 24. ) -callalive Enable or disable auto-disconnection after 10 seconds not receiving packets from remote party.
PLANET VIP-101T CLI configuration Parameter –plan is used to setup dialstring length. While the number (E.164 number in phone book) you dialed is 7 digits, this parameter should be configured as 7 or 0. Syntax Description -plan dial string length ( number 1 ~ 24 to limit the dialed digits, 0 for unlimited, but Max. dialed digits is 24. ) Default 0 (not limited, Max. allowed dialed digits count is 24.) 1. If this parameter is set to 0, this will disable length checking in phone book (Max.
PLANET VIP-101T CLI configuration Default 2 (H.245 signal type) G It is not suggested to change this parameter without assistance of your VoIP or PBX Note system administrator. e) –idto Parameter –idto is used to setup the interval (in second) of two pressed digits, iff there is no action in this duration, VIP-101T will dial out the pressed numbers. Syntax Description -idto Interval between dial string Digits.
PLANET VIP-101T CLI configuration 13. [h323] h323 command is used to display or configure H.323 parameters in VIP-101T, these parameters are designed to meet most calling environment. It is strongly recommended not to modify these parameters on your own. If you met difficulty to establish communication toward destination call party, please consult ITSP engineering staff, experienced personnel or local distributor support staff for proper configuration. There are sub parameters in VIP H.
PLANET VIP-101T CLI configuration usr/config$ h323 H.323 stack information and configuration Usage: h323 [-mode gkmode] h323 [-gk ipaddress] [-algk ipaddress] [-gkdis used] [-e164 number] [-e164-x number] [-alias h323id] [-tokenpwd password] [-rtp port] [-ttl time] [-gkfind port] [-ras port] [-range [start num1] [end num2]] [-respto t1] [-connto t2] [-dfgw IP] h323 -print -print Display H.323 stack information and configuration. -mode Configure as Gatekeeper mode or Non-GateKeeper mode.
PLANET VIP-101T CLI configuration running mode is Peer-to-Peer mode. Syntax Description –mode 0/1 (0 for GateKeeper mode ,1 for Peer-to-Peer mode) Default 1 (Peer-to-Peer mode) c) –gk This parameter is used to configure primary GateKeeper IP address Syntax Description –gk IP address or URL of destination Gatekeeper Default Null (This command has no default value.) 1. In the GK IP field, URL can be inserted as well.
PLANET VIP-101T CLI configuration Syntax Description -dfgw Destination H.323 Gateway IP Address. Default x (no default destination H.323 gateway) e) –algk This parameter is used to configure secondary Gatekeeper IP address or URL address. If VIP-101T tries to register to primary Gatekeeper for 10 times but failed, it will try to register to secondary (alternative) Gatekeeper configured in this option. Syntax Description -algk IP address of Secondary Gatekeeper.
PLANET VIP-101T CLI configuration Default 1001 h) –e164-x You may assign up to 10 E.164 numbers (Registered telephone numbers) in VIP-101T phone book database. For example, 10 users share the same VIP-101T, they can assign phone numbers as 100, 200, 300…. (for example, h323 –e164 100 –e164-1 200 –e164-2 300….) User can disable one number and the number after this one. Ex. from set 1-5 is configured, if user set the third number as “x”, from third to fifth number will be disabled at the mean time. (ex.
PLANET VIP-101T CLI configuration j) –tokenpwd To co work in a H.235 security environment, VIP-101T is implemented the sending capability of RRQ/ARQ authentication token password to Gatekeeper for authentication purpose. Syntax Description -tokenpwd RRQ/ARQ authentication token password while registering toward Gatekeeper.
PLANET VIP-101T CLI configuration l) –rtp This parameter is used to assign RTP port number for voice packet transmission, definable port range: 1024-65535. Syntax Description -rtp RTP port number (1024~65532). Default 16384 m) –ttl This parameter is used to set RAS TTL (time-to-live) time while machine performs registration toward Gatekeeper. Definable time range: 0-3600 second(s). Syntax Description -ttl RAS TTL time (0~3600 second). Default 60 seconds.
PLANET VIP-101T CLI configuration -ras Destination Gatekeeper RAS port (1024~65535). Default 1719 p) –range This parameter is used to assign dynamically allocated port range, definable port range: 1024-65535. Syntax Description -range Dynamically allocated port range (1024~65535) in VIP-101T. Default 1024-65535 q) –respto This parameter is used to setup Max. waiting time for first response from detination call party during call setup process.
PLANET VIP-101T CLI configuration G Note 1. Parameters in this H.323 configuration menu are not suggested to change without assistance of ITSP or experienced personnel, improper configuration will case communications fail or malfunction in machine. 2. In Peer-to-Peer mode, h323 –print will only display information on e164, alias, mode, RTP port, and allocated port range fields. 3. In Peer-to-Peer mode, please dial “#” after press IP address (ex.10.1.1.1 please dial 10*1*1*1#) or E.
PLANET VIP-101T CLI configuration Voice codec setting information and configuration Usage: voice [-send [G723 ms] [G711A ms] [G711U ms] [G729A ms] [G729 ms] ] [-volume [voice level] [input level] [dtmf level]] [-nscng G723 used] [-echo used] [-mindelay/maxdelay used] voice -print voice -priority [G723] [G711A] [G711U] [G729A] [G729] -print -send Display voice codec information and configuration. Specify sending packet size. G.723 (30/60 ms) G.711A (20/40/60 ms) G.711U (20/40/60 ms) G.729A (20/40/60 ms) G.
PLANET VIP-101T CLI configuration -print Display voice codec information and configuration. Default This command has no default value. Example usr/config$ voice -print Voice codec setting relate information Sending packet size : G.723.1 : 30 ms G.729A : 20 ms G.729 : 20 ms G.711U : 20 ms G.711A : 20 ms Priority order codec : g7231 g729a g729 g711u g711a Volume levels : voice volume : 30 input gain : 26 dtmf volume : 23 Silence suppression & CNG: G.723.
PLANET VIP-101T CLI configuration c) -priority Parameter –priority can be used to setup supported voice codec or priority in voice codecs during capability exchange in H.323 call setup process. You may set from 1 to 5 codecs to meet real world applications. For instance, voice –priority g723 means VIP-101T supports single voice codec (G.723.1) only.
PLANET VIP-101T CLI configuration on. Syntax Description -echo Setting of echo canceller.
PLANET VIP-101T CLI configuration network. 1. -print : display current TOS values configurations. 2. -rtptype : configure TOS type of RTP packets from 0 to 7 3. -rtcptype : configure TOS type of RTCP packets from 0 to 7 4. -rtpdelay : configure RTP packets as normal delay or low delay 5. -rtcpdelay : configure RTCP packets as normal delay or low delay 6. -rtpthruput : configure RTP packets as normal throughput or high throughput 7.
PLANET VIP-101T CLI configuration please set high frequency and related items as 0. Furthermore, unit of on/off time is 1/100 second, and it is suggested to keep this as default value.
PLANET VIP-101T CLI configuration a) -print Parameter –print is used to display current SUPPORT values configurations. Syntax Description This command has no arguments or keywords. Default This command has no default value. b) –fstart Parameter –fstart is used to enable or disable H.323 fast start mode. If you’d like to enable H.323 fast start mode in VIP-101T, please make sure the destination call party supports fast start mode as well.
PLANET VIP-101T CLI configuration Syntax Description -h245fs H.245 separate channel after H.323 faststart mode. Default 0 H.245 separate channel mode is disabled. When H.323 fast start mode is enabled, if you wish to send DTMF message G after connection, VIP-101T will send out Q.931 message to destination call Note party. You’ll need to specify the Keypad type as “Q.931” in System configuration menu. 18. [bureau] This parameter is used while other call party supports H.450 Hold feature.
PLANET VIP-101T CLI configuration Default This command has no default value. b) -hold If other terminals support H.450 hold function, and execute hold function when connecting with VIP-101T, user will hear hold tone from VIP-101T. (0 for off,1 for on) Syntax Description -hold Enable or disable H.450 service hold tone generation, 0 for disable and 1 for enable. Default 1 H.450 hold feature is turned on. 19.[rom] Command rom is used to perform firmware upgrade in VIP-101T.
PLANET VIP-101T CLI configuration Back Tone PCM file and Hold Tone. In most circumstances, upgrade the main application image can retrieve the latest features or maintenance, no other file required. If there are additional demands for other kinds of image file, we’ll include in the firmware release for customer’s most convenience. To perform firmware upgrade, you’ll need to setup a TFTP server or FTP server to complete upgrade process. Please consult experienced personnel to prepare related service.
PLANET VIP-101T CLI configuration TFTP/FTP server. Syntax Description -f Specify firmware file name on the destination TFTP/FTP server. Default This command has no default value f) –server Parameter –server is used to specify TFTP/FTP server IP address, which will be stored in flash memory for the convenience of future firmware upgrade. This feature also can be configured on LCD configuration menu -firmware upgrade, -Set file Server IP.
PLANET VIP-101T CLI configuration -ftp specify username and password for FTP Default This command has no default value 20.[passwd] For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by VIP-101T. usr/config$ passwd Password setting information and configuration Usage: passwd -set Loginname Password passwd -clean Note: 1. Loginname can only be 'root' or 'administrator'. 2.
PLANET VIP-101T CLI configuration b) –clean Parameter -clean can be used to erase the existing password stored in machine. To perfor this command, you need to logon as root user to have sufficient privilege to execute this command. After password erased, you may logon VIP-101T via username/password: root/ null or administrator/ null. Syntax Description This command has no arguments or keywords. Default This command has no default value.
