4-Channel Video over Fiber Bundle Kit VF-402-KIT User's Manual
Copyright Copyright © 2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Statement This device complies with FCC radiation exposure set forth for an uncontrolled environment.
Table of Contents Chapter 1. Product Introduction......................................................................... 5 1.1 Package Contents................................................................................. 5 1.2 Product Description............................................................................... 5 1.3 Application........................................................................................... 8 1.4 Product Features................................................
Chapter 1. Product Introduction 1.1 Package Contents Check the contents of your package for the following parts: zz VF-402-T – Video over Fiber Media Converter (Transmitter) x 1 zz VF-402-R – Video over Fiber Media Converter (Receiver) x 1 zz 5V / 2A Power Adapter x 2 zz User’s Manual x 1 Note If any of the above items are missing, please contact your dealer immediately. 1.
Fiber Optic Communication for Video and Serial Data The VF-402-KIT consists of a Video Transmitter and a Video Receiver: zz VF-402-T: 4-channel Video over Fiber Transmitter zz VF-402-R: 4-channel Video over Fiber Receiver The VF-402-KIT is a digital fiber-optic transmission system that brings users a cost-effective solution for transmission of 4-channel uncompressed digital video and one reverse RS485 async data over one single fiber cable.
Industrial Monitoring Systems The industrial-level VF-402-KIT’s super wide temperature ranges from -20 to 70 degrees C, applicable to all kinds of environments. It supports hot plugging and its 4-channel video adopts the full digital video non-compression and Gigabit fiber optic transmission technology that brings distortion-free videos over a long-distance fiber cable. Thus, it can observe working condition visually with LED.
1.3 Application The VF-402-KIT consists of 4-channel video over fiber optical transceiver and receiver to transmit video and RS485 signal through a reliable single mode or single fiber link. It is an ideal cost-effective solution for surveillance system that requires high display quality and high-performance signal transmission over long distances.
Typical Applications zz Intelligent Transportation Systems (ITS) zz Toll Collection zz Traffic Surveillance zz Air Traffic Management (ATM) zz Rail Signaling zz Perimeter Alarms and Area Monitoring zz Telemedicine and Teleconference zz Industrial Surveillance zz Intelligent Building zz CCTV Network 1.
1.5 Product Specifications Model VF-402-T VF-402-R Video Characteristics Video Channel 4-channel bi-direction Video Connector BNC Supported Video Type 1080p: AHD/TVI/CVI 480p: CVBS Video Input/Output Impedance 75ohm/unbalanced interface Video Input/Output Voltage 1.
Hardware Specifications LED Indicators • Power • Each channel • Link (fiber optic) Dimensions (W x D x H) 157 × 116.5 × 48 mm Weight 580g Power Requirement 5V DC, 2A Chassis Current Consumption 1.
11.3 8.1 1.6 Dimensions of Installing OPT 9.3 8 8 5V DC 8.4 58.3 141.12 130.92 118.52 8-R 13.4 1.5 93.32 13.4 157 5 3.2 8-R 19.2 17.2 17.2 17.2 21.21 D1- D2+ D2- GND 106.35 12 5.1 10.2 14.05 D1+ 5.93 9.7 5 15 17.
Chapter 2. Hardware Description 2.1 Panel Overview Front Panel: D1+ D1- D2+ D2- GND 5.1 Video interface Item Description VIDEO/V1…V4 Video input interface LED definition PWR: Power indicators -- when powered on, PWR LED is on. LNK: Optical link indicator -- after connecting the fiber connector, the indicator will show green when optical signal is detected. But the indicator will be off when optical signal is not detected.
Rear Panel: There is a power interface on the rear panel; the description of each is as follows: OPT 5V DC Power Supply Power supply Output Note 5V DC, 2A 1. The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime. 2.
Chapter 3. Installation This section describes how to install your VF-402-KIT Video over fiber and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET VF402-KIT Video over fiber Converter does not need software configuration. To install your VF-402-KIT on a desktop or shelf, check the following sections. 3.1 Limitation The Video over fiber Converter does not require any software configuration.
(7) The relation of the video of optical transmitter and optical receiver is one-to-one, which means V1~V4 of optical transmitter is one-to-one to V1~V4 of optical transmitter. 3.3 Order for installation (1) Connect the interface of optical transmitter with camera or speed dome. Then connect the optical fiber and the power supply. (2) Connect the interface of optical receiver with video interface, monitor, video matrix and displayer. Then connect the optical fiber and the power supply.
(5) Connect the 5V DC power adapter to the VF-402-T/VF-402-R and verify that the Power LED lights up. (6) Turn on the power of the analog camera/monitor; the video LED (green) should be lit when all cables are connected. Video DVR / Monitor Up to 20km Video |O|O| Speed Dome VF-402-T VF-402-R Transmitter Receiver |O|O| Control Keyboard Video Video Line Fiber-optic Wire |O|O| Serial Line (RS-485) 3.
Wall Mount: Mount device on the wall with screws 18
Chapter 4. Precautions (1) Insert fiber rightly into the fiber interface; avoid breaking off fiber because of applying too much force. The rolling diameter shall not be too short (not less than 20cm). (2) Fasten the retaining screw after connecting terminal blocks. (3) Do not remove the dust cap before installation. Make sure to prevent dirt and other things from getting into port or else the loss of optical signal will be increased and the transmission quality will be affected.
Chapter 5. Troubleshooting Question Answer or Solution Power supply indicator is off. Check if the power plug is tightly connected and check the fuse wire of chassis. Abnormal video data. Check if local interference, poor-quality monitor and optical output power are normal and in the range of receiving sensitivity. Irregular horizontal grain or video images.
