4-Channel Video over Fiber Bundle Kit VF-402-KIT Manual
Copyright Copyright © 2013 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
FCC Caution To assure continued compliance. (example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. This device complies with Part 15 of the FCC Rules.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
Table of Contents Chapter 1. Product Introduction......................................................................... 6 1.1 Package Contents................................................................................. 6 1.2 Product Description............................................................................... 6 1.3 Application........................................................................................... 9 1.4 Product Features................................................
Chapter 1. Product Introduction 1.
Fiber Optic Communication for VIDEO and SERIAL DATA This Video over Fiber Converter kit consists of a Video Transmitter and a Video Receiver: l VF-402-T: 4-channel Video over Fiber Transmitter l VF-402-R: 4-channel Video over Fiber Receiver Fiber-optic transmission system This Video over Fiber Converter kit consists of a Video Transmitter, VF-402-T, and a Video Receiver, VF-402-R (Figure 1).
Industrial monitoring systems Industrial level super wide temperature range -25 to 75 Degree C, applicable to lots kinds of environment, also support hot plug, VF-402-KIT, 4 channel video adopts advanced international no compression full digital error correction and gigabit fiber optical transmission technology to fulfill VF-402-KIT without distortion from longdistance in high quality through one fiber. This series of optical transceiver is of stable performance and clear graphics.
1.3 Application The VF-402-KIT consists of 4 channel video over fiber optical transceiver and receiver to transmit video and RS-485 signal through a reliable single mode / single fiber link. It is an ideal cost-effective solution for surveillance system that requires high display quality and high performance signal transmission over long distances.
Typical Applications ll Intelligent Transportation Systems (ITS) ll Toll Collection ll Traffic Surveillance ll Air Traffic Management (ATM) ll Rail Signaling ll Perimeter Alarms and Area Monitors ll Telemedicine and Teleconference ll Industrial Surveillance ll Intelligent Building ll CCTV network 1.
Video Digital Bit Width 8/10 bit Differential Gain (DG) <1.3% (Typical Value) Differential Phase (DP) <1.3° (Typical Value) SNR Weighted >63dB (Typical Value) Data Interface Data Channel 4 channel Physical Protocol RS-485 Operation Mode Simplex Data Connector 4 Pin terminal block with screw clamps Data Rate DC-150Kbps Data Distance RS-485: 0-20km BPS 0-115.
Environment Operating Temperature: -25 ~ 75 Degree C Relative Humidity: 0 ~ 95% (non-condensing) Storage Temperature: -40 ~ 85 Degree C Relative Humidity: 5 ~ 95% (non-condensing) 1.
Chapter 2. Hardware Description 2.1 Panel Overview ■ Front Panel: P1 OPT PWR LNK V1 V2 V3 V4 ■ Video interface Item Description VIDEO/V1…V4 Video input interface ■ Fiber interface Item Description FIBER/OPT Fiber interface (Warning: In case of damage to eyesight, Do not look directly into interface on electrify state). For Optical transceiver B type, this interface is empty, wiring out from the rear panel. ■ LED definition PWR: Power indicators.
■ Rear Panel: There is a power interface and power indicator on the rear panel, both PWR is ON when power on. FIBER is fiber interface; the description of each is as follows: POWER GND ■ Power Supply Power supply… Input AC 90~264V, 50~60HZ Output 5V / 2A Power Notice 14 1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device.
Chapter 3. Installation This section describes how to install your VF-402-KIT Video over Fiber and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET VF-402-KIT Video over Fiber Converter do not need software configuration. To install your VF-402-KIT on a desktop or shelf, simply complete the following steps. 3.1 Limitation The Video over Fiber Converter does not require any software configuration.
(7) The relation of the video of optical transmitter and optical receiver is one-to-one, which means V1~V4 of optical transmitter is one-to-one to V1~V4 of optical receiver. 3.3 Order for installation (1) Connect the interface of optical transmitter with camera or speed dome. Then connect the optical fiber and the power supply. (2) Connect the interface of optical receiver with video interface, monitor, video matrix and displayer. Then connect the optical fiber and the power supply.
3.4 Stand-alone Installation To install a VF-402-T / VF-402-R stand-alone, on a desktop or shelf, simply complete the following steps: Step 1: Turn off the power of the analog camera / monitor to which the VF-402-T / VF-402-R will be attached. Step 2: VF-402-T (Transmitter): Connect coaxial cable from analog camera to Video BNC port of the VF-402-T. Step 3: Attach FC single mode fiber cable from the VF-402-T to VF-402-R in the remote side.
3.
Appendix A: Precautions (1) Insert fiber rightly into the fiber interface; avoid breaking off fiber because of applying too much force. The rolling diameter shall not be too short (not less than 20CM). (2) Fasten the retaining screw after connecting terminal blocks. (3) Do not remove the dust cap before installation, in order to avoid dirt and other things getting into port, increasing the loss of optical signal and affecting the transmission quality.
Appendix B: Troubleshooting Question Answer or Resolution Power supply indicator is OFF Check if the power plug is loose and the fuse wire of chassis. Abnormal video data Check if optical output power is normal and in the range of receiving sensitivity.
