Optical Fiber Transmission System VF-10x-KIT User’s Manual
Trademarks Copyright © PLANET Technology Corp. 2015 Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners.
FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications.
WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision Video over Optical Fiber Media Converter User’s Manual For Models: VF-10x-T / VF-10x-R Rev 1.2 (July 2015) Part No.
Table of Contents 1. Introduction...................................................................... 6 1.1 Check List.................................................................. 6 1.2 Introduction To Video Over Fiber Converter................... 6 1.3 Key Features............................................................... 7 1.4 Product Specification................................................... 7 2. Hardware Description....................................................... 11 2.
1. Introduction 1.1 Check List Check your package for the following parts: ll VF-10x-T – Video over Fiber Media Converter / Transmitter x 1 ll VF-10x-R – Video over Fiber Media Converter / Receiver x 1 ll 5V/2A Power Adapter x 2 ll User’s Manual x 1 If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. 1.
n Air Traffic Management (ATM) n Rail Signaling n Perimeter Alarms and Area Monitoring n Telemedicine and Teleconference n Industrial Surveillance n Intelligent Building 1.3 Key Features n Video + Data over fiber transmission n 8 bit Video Signal digital sampling n PAL, NTSC, SECAM compatible n Data Type: RS485 n Standalone or work with PLANET MC-700/1500/1500R Media Converter Chassis n Compact in size, wall-mount design, easy installation 1.
Video Bandwidth 6.5MHz Video Digital Bit Width 8/10 bit Differential Gain (DG) < 1.3% (typical value) Differential Phase (DP) < 1.3° (typical value) SNR Weighted 63dB (typical value) Data Interface Data Channel 1 channel Physical Protocol RS485 Operation Mode Simplex Data Connector 3-pin terminal block with screw clamps Data Rate DC-115.
VF-101-KIT VF-101-T TX & RX: 1310nm VF-101-R TX & RX: 1310nm VF-102-T TX: 1310nm, RX: 1550nm VF-102-R TX: 1550nm, RX: 1330nm VF-102SC-T TX & RX: 1310nm VF-102SC-R TX & RX: 1310nm VF-102-KIT Optical Wavelength VF-102SC-KIT VF-102S15-KIT VF-102S15-T TX & RX: 1310nm VF-102S15-R TX & RX: 1310nm VF-106-T TX: 1310nm, RX: 1550nm VF-106-R TX: 1550nm, RX: 1330nm VF-106-KIT Launch Power (dBm) Receive Sensitivity (dBm) VF-101-KIT Max.: -14, Min.: -19 VF-102-KIT Max.: -7, Min.
Max. Input Power (dBm) VF-101-KIT -14 VF-102-KIT 0 VF-102SC-KIT -14 VF-102S15-KIT -8 VF-106-KIT Cable 0 50/125μm or 62.5/125μm multi-mode cable 9/125μm single-mode cable Hardware Specification LED Indicators • One for Power • One for Video - Green, Link • One for Fiber Optic - Green, Link Dimensions (W x D x H) 94 x 70 x 26 mm Weight 215g Power Requirement 5V/2A Power Consumption 4.
2. Hardware Description 2.1 Front Panel The units’ front panels provide a simple interface monitoring the converter. There are fiber optic interface and video socket on the front panel. For the VF-10x-T/VF-10x-R, with reverse data connector, the RS485 data port may be connected to the user’s interface end.
2.1.1 Ports connection Video Connection Connect the video signal to or from the product through a 75Ω coax cable with BNC plug. Async-data Connection n Connect the output data port (e.g. TX+ and TX-) of the other controlled device to the RX+ and RX- of the RX n Connect the input data port (e.g.
2.2 Rear Panel The rear panel of the converter has one DC jack, which accepts an input power of 5V DC at 2A. Power Notice 1. The device is a power-required device, meaning it will not work till it is powered. If your network should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device to prevent you from network data loss or network downtime. 2.
3 Installing The Converter This section describes how to install your VF-10x Media Converter and make connections to the converter. Please read the following sections and perform the procedures in the order being presented. The hardware installation of PLANET VF-10x Media Converter does not need software configuration. To install your VF-10x on a desktop or shelf, simply complete the following steps. 3.1 Limitation The converter does not require any software configuration.
Step 3: Attach FC single mode fiber cable from the VF-10x-T to VF-10x-R in the remote site. Step 4: VF-10x-R (Receiver): Connect coaxial cable from monitor/DVR to video BNC port of the VF-10x-R. Step 5: Connect the 5V DC power adapter to the VF-10x-T/ VF-10x-R and verify that the power LED lights up. Step 6: Turn on the power of the analog camera/monitor; the video LED (green) should light up when all cables are attached.
3.3 Chassis Installation and Rack Mounting To install the Video over fiber Converter in a 10-inch or 19-inch Converter Chassis with standard rack, follow the instructions described below. Step 1: Place your Converter Chassis on a hard flat surface, with the front panel positioned toward your front side. Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the Converter Chassis.
Coax Video Camera VF-10X-T Coax Media Converter Chassis Video Coax Video Camera Video Video VF-10X-T Video DVR / Monitor Coax VF-10X-R Video |O|O| |O|O| VF-10X-T Speed Dome Control Keyboard Coax Fiber-optic Video |O|O| Speed Dome Video Video Line |O|O| Serial Line (RS485) VF-10X-T Figure 3-3 VF-10x-T/VF-10x-R media converter chassis installation 17
3.4 Optional DIN-rail Mounting There are two DIN-rail holes on the left side of the VF-10x-T/ VF-10x-R that allows the converter to be easily installed with DIN-rail mounting. PLANET optional DIN-rail mounting kit – RKE-DIN – can be ordered separately. When the wall mount application needs to be replaced with the DIN-rail application for the VF-10x-T/VF-10x-R, please refer to the following figures to attach the DIN-rail to the converter.
Step 3: Check whether the DIN-rail is tightly on the track. You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.
4. Power Information The central post of the power jack of the VF-10x-T/VF-10x-R measures 2.5mm, and +5VDC power input is required. It conforms to the bundled AC-DC adapter and Planet’s Media Converter Chassis. If you have a power connection issue, please contact your local sales representative. Please keep the AC-DC adapter as a spare item when your VF-10x is installed to a Media Converter Chassis. 2.5mm DC Receptacle 2.5mm +5V for each slot DC receptacle is 2.5mm wide that conforms to 2.
