4-in-1 Video over Gigabit Fiber Bundle Kit VF-101G/102G/106G-KIT User’s Manual
Copyright Copyright © 2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the device and receiver. 3.
CE Mark Warning Warning: This equipment is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Safety Instructions This device is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical device.
Table of Contents Chapter 1. Product Introduction.............................................. 6 1.1 Package Contents........................................................ 6 1.2 Product Description..................................................... 6 1.3 Application.................................................................. 8 1.4 Product Features....................................................... 10 1.5 Product Specifications................................................ 10 Chapter 2.
Chapter 1. Product Introduction 1.1 Package Contents Check the contents of your package for the following parts: zz VF-101G/102G/106G-T – Video over Fiber Media Converter (Transmitter) x 1 zz VF-101G/102G/106G-R – Video over Fiber Media Converter (Receiver) x 1 zz 5V Power Adapter x 2 zz User’s Manual x 1 Note If any of the above items are missing, please contact your dealer immediately. 1.
VI AH T D S VI C B CV Fiber Optic Communication for Video and Serial Data This Video over Gigabit Fiber Converter kit consists of a Video Transmitter and a Video Receiver: zz VF-101G/102G/106G-T: 1-channel Video over Gigabit Fiber Transmitter zz VF-101G/102G/106G-R: 1-channel Video over Gigabit Fiber Receiver The VF-101G/102G/106G-KIT is a digital fiber-optic transmission system that brings users a cost-effective solution for transmission of 1 channel uncompressed digital video and one reverse RS485
Coax Video HDVR / Monitor Coax Up to 20km Video 1000 RS485 RS485 Speed Dome VF-101G/102G/106G-T Transmitter VF-101G/102G/106G-R Receiver Control Keyboard 1000 Gigabit Fiber-optic Video Video Line RS485 RS485 Easy Installation Simply by Plug and Play, the installation of the VF-101G/102G/106G-KIT media conversion is quite easy. They can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis (MC-700, MC-1500 and MC-1500R).
signal through a reliable single mode or single fiber link. It is an ideal cost-effective solution for surveillance system that requires high display quality and high-performance signal transmission over long distances. The VF-101G/102G/106G-KIT can be installed easily by way of “Plug and Play”, meaning the operator does not need to configure the pair of the video over fiber transmission in advance.
1.
Video Digital Bit Width 8/10 bit Differential Gain(DG) < 1.3% (typical value) Differential Phase(DP) < 1.3° (typical value) SNR Weighted > 67dB (typical value) Data Interface Data Channel 1 channel Physical Protocol RS485 Operation Mode Simplex Data Connector 3 Pin terminal block with screw clamps Data Rate DC-115.
Dimensions (W x D x H) 94 x 70 x 26 mm Weight 200g Power Requirement 5V DC, 2A Power Consumption 4.
Chapter 2. Hardware Description 2.1 Front Panel The front panel of the VF-101G-T/VF-101G-R comes with two fiber optic interfaces and one video socket, while those of the VF-102G-T/VF-102G-R and VF-106G-T/VF-106G-R each have one fiber optic interface and one video socket. For the VF-101G/102G/106G-T and VF-101G/102G/106G-R, With the reverse data connector, the RS485 data port of the VF-101G/102G/106G-T or VF-101G/102G/106G-R can be connected to the user’s interface.
zz LED Definition Color Function PWR LED Green Lights to indicate that the device is powered. VIDEO Green Lights when the device receives video signal. LNK Green Lights when the fiber connection is established. 2.2 Rear Panel The rear panel of the converter has one DC jack, which accepts an input power of 5V DC at 2A. zz Power Supply Power supply Output Note 14 5V DC, 2A 1. The device is a power-required device, meaning it will not work till it is powered.
zz Fiber Interface Item Description FIBER/OPT FC-type fiber interface. Note After the VF-101G/102G/106G-KIT is powered on, wait for at least 15 seconds before connecting the connector to the optical fiber port or else the connector may be damaged or you may get an electric shock.
Chapter 3. Installation This section describes how to install your VF-101G/102G/106G-KIT Video over Fiber and make connections to the converter. Please read the following sections and perform the procedures in the order being presented. The hardware installation of PLANET VF-101G/102G/106G-KIT Video over Fiber Converter does not need software configuration. To install your VF-101G/102G/106G-KIT on a desktop or shelf, check the following sections. 3.
(2) Please carefully read the safety instructions. (3) Optical transceiver equipment shall not be disassembled by anyone without authorization. (4) Check the product model tag stuck outside the cabinet to prevent incorrect installation. (5) The relation of the video of optical transmitter and optical receiver is one-to-one. 3.
(4) VF-101G/102G/106G-R (Receiver): cable from monitor/HDVR to Video VF-101G/102G/106G-R. Connect BNC port coaxial of the (5) Connect the 5V DC power adapter to VF-101G/102G/106G-T and VF-101G/102G/106G-R, make sure that the power is on and the link LED is lit. the and (6) Turn on the power of the analog camera/monitor; the video LED should be lit when all cables are connected.
(3) Attach a rack-mount bracket to each side of the Converter Chassis with supplied screws attached to the package. (4) After the brackets are attached to the Converter Chassis, use suitable screws to securely attach the brackets to the rack. (5) Connect the video and fiber cabling, and supply power to your Converter Chassis. 3.
(2) Lightly press and push the DIN-rail into the track. (3) Check whether the DIN-rail is tightly on the track. Note 20 You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.
Chapter 4. Precautions (1) Insert fiber correctly into the fiber interface; try not to apply too much force to avoid breaking the fiber. The rolling diameter cannot be less than 20cm. (2) Fasten the retaining screw after connecting terminal blocks. (3) Do not remove the dust cap before installation. Make sure to prevent dirt and other things from getting into port or else the loss of optical signal will be increased and the transmission quality will be affected.
Chapter 5. Power Information The central post of the power jack of the VF-101G/102G/106G-T or VF-101G/102G/106G-R measures 2.5mm, and +5V DC/2A power input is required. It conforms to the bundled AC-DC adapter and Planet’s Media Converter Chassis. If you have a power connection issue, please contact your local sales representative. Please keep the AC-DC adapter as a spare item when your VF-101G/102G/106G is installed to a Media Converter Chassis. 2.5mm DC Receptacle 2.
Chapter 6. Troubleshooting Q1: [VF-101G-KIT/VF-102G-KIT/VF-106G-KIT] Why didn’t the monitor display anything or DVR record anything after the analog camera, VF-10xG-KIT and cables are well connected? A: 1. Check the corresponding devices: zz The analog camera should connect to the VF-10xG-T – the video transmitter. zz The monitor / DVR should connect to the VF-10xG-R – the video receiver. When you do the reverse way, the connection cannot be established. 2.
Q3: [VF-101G-KIT/VF-102G-KIT/VF-106G-KIT] Why did the monitor connected to HDVR display show black and white video? A: The VF-10xG-KIT supports AHD/TVI/CVI/CVBS video. Please make sure your camera is set as AHD/TVI/CVI/CVBS mode and adjust the HDVR to a corresponding mode. For example, set the camera and HDVR as an AHD mode.
