Gigabit Ethernet over Coaxial Converter VC-232G User’s Manual
Trademarks Copyright © PLANET Technology Corp. 2017. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp.
energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Table of Contents 1. Package Contents.............................................................. 5 2. Hardware Introduction....................................................... 6 2.1 Physical Dimensions.................................................... 6 2.2 Front View.................................................................. 7 2.3 Rear View.................................................................. 9 3. Product Specifications......................................................
1. Package Contents Thank you for purchasing PLANET VC-232G 1-Port 10/100/1000T Ethernet over Coaxial Converter. In the following sections, the term “EoC Converter” means the VC-232G. Open the box of the EoC Converter and carefully unpack it.
2. Hardware Introduction 2.1 Physical Dimensions 8dB Sym. SNR Band Asym. 12dB Tran. G.INP Interleave CO TP 10/100/1000 5V DC 1000 100 PWR Ethernet over VDSL 2 Converter Mode CO CPE CPE 1 VDSL ON 2 3 4 OFF VC-232G Ethernet over VDSL 2 Converter 6 ON Dimensions (W x D x H): 94 x 70.
2.2 Front View VC-232G Front Panel VDSL 1000 TP 100 PWR CO VC-232G CPE 10/100/1000 Ethernet over VDSL 2 Converter ¾¾ 10/100/1000BASE-T RJ45 connector ¾¾ BNC female connector for VDSL2 ¾¾ LEDs for power, Ethernet and VDSL ¾¾ CO/CPE mode selectable via DIP switch VC-232G LED Indicators The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system. System LED PWR Color Function Lit Indicates that the EoC Converter has power.
VDSL LED Color Function Lit VDSL Green Indicates that the VDSL connection is established. Fast Indicates that the VDSL connection is at Blink training status (about 10 seconds). Slow Indicates that the VDSL connection is at Blink idle status. CO Green Lit Indicates the EoC Converter is running in CO mode. CPE Green Lit Indicates the EoC Converter is running in CPE mode.
2.3 Rear View VC-232G Front Panel 5V DC Mode Tran. Band CO G.INP Asym. 12dB CPE Interleave Sym. SNR 8dB OFF 1 ON 2 3 4 ON ¾¾ DIP switch ¾¾ DC jack (DC input) for power adapter DIP Switch The EoC Converter provides a selectable 4-position DIP switch. Switch them on or off to obtain the best coaxial cable connection over a distance. DIP-1 DIP DIP-3 DIP-4 Transmission Band Profile SNR Margin OFF CO G.
DIP-1: Mode (CO/CPE) CO (Central Office) The Master device mode, usually the CO device, is located at the data center of ISP or enterprise to link to the backbone. CPE (Customer Premises Equipment) The Slave device mode, usually the CPE device, is located at branch office, home or remote side as the long reach data receiver. The CPE can be connected to the PC, IP camera or wireless access point or other network devices.
DIP-4: SNR (Signal Noise Ratio) Margin When the SNR margin is selected, the system provides 12dB/8dB SNR margin for all usable loop lengths. Better channel noise protection is made with the higher SNR margin. Note Please power off the VDSL2 Bridge before making any transmission mode adjustment. DC Power Jack The VC-232G requires 5V DC, 2A power input, which conforms to the bundled AC adapter. Should you have the issue of power connection, please contact your local sales representative. 2.
3. Product Specifications Product VC-232G Hardware Specifications TP interface 1 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports 1 BNC female Ethernet over Coaxial VDSL Interface Cabling Coaxial cable: 75 ohm RG-6/U cable, less than12Ω/1000 ft RG-59/U cable, less than 30Ω/1000 ft. Maximum Max. 1400m with data transmission Distance (4,593ft.) Functionality DIP-1 Select CO or CPE mode DIP-2 Select G.
Housing Metal System Specifications VDSL Compliance VDSL-DMT ITU-T G.993.1 VDSL ITU-T G.997.1 ITU-T G.993.2 VDSL2 (Profile 17a/30a Support) ITU-T G.993.5 G. Vectoring ITU-T G.998 G.INP Standards Conformance Standards Compliance IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3ab Gigabit Ethernet IEEE 802.3x Full-duplex flow control IEEE 802.1p Class of Service ITU-T G.993.1 VDSL ITU-T G.997.1 ITU-T G.993.2 VDSL2 (Profile 17a/30a Support) ITU-T G.993.5 G.Vectoring and G.INP ITU-T G.
4. Applications The EoC Converter does not require any software configuration. Users can immediately use any feature of this product simply by attaching the cables and turning the power on. There are some key limitations on the EoC Converter. Please check the following items. 4.1 Point-to-Point Application -- LAN to LAN Connection One set of the EoC Converter could be used to link two local Area networks that are located in different places.
3. Power on the VC-232G CO and CPE at both sides by connecting its power source. 4. Power, CO and CPE LED will illuminate correspondingly. 5. Connect coaxial cable from LAN1 VC-232G to VDSL BNC port of the LAN2 VC-232G. 6. VDSL LNK LED will blink to illuminate at both VDSL2 bridges. 7. Connect the VC-232G Ethernet LAN port to other network device via regular Cat.5 UTP cable. 4.2 VC-232G Point to Multi-point Application (IP surveillance) L2+ Switch NVR Video DC DC VC-232G VC-232G (CO) (CO) Coax.
Building a IP surveillance system Refer to the following procedure to set up many pairs of VC-232G to IP surveillance system. 1. Set the VC-232G to be CO and CPE mode from the DIP switch on the rear panel. 2. Power on the VC-232G by connecting its power source. 3. Power LED will illuminate. 4. Connect Coaxial cable from VDSL port of two VC-232G units. 5. VDSL LED will blink to illuminate. 6. Connect Ethernet port to IP cameras via regular Cat. 5, 5e or 6 cable. 7.
5. Installations Installing Ethernet over Coaxial Converter 5.1 Wall-mount Installation Step 1: Please find the wall that can mount the VC-232G Step 2: Screw two screws on the wall. Step 3: Hang the VC-232G on the screws from the wall. Step 4: Repeat Step 5 of Desktop Installation for power supply to the VC-232G Note Before mounting the device to the wall, please check the location of the electrical outlet and the length of the Ethernet cable.
5.2 Chassis Installation and Rack Mounting To install the EoC Converter in a 10-inch or 19-inch Converter Chassis with standard rack, follow the instructions described below. Step 1: Place your VC-232G on a hard flat surface, with the front panel positioned towards your front side. Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the converter chassis.
6. Performance Table VC-232G Performance Interleave (Upstream/Downstream) CO DIP Switch Distance (meter) Asymmetric 8dB 12dB 200 88/168 400 75/160 600 800 12dB 78/145 129/131 117/123 69/137 117/122 102/102 59/129 48/118 101/92 88/82 32/110 26/94 62/73 47/56 G.
7. Troubleshooting SYMPTOM: VDSL LNK LED does not light up after wire is connected to the VDSL port. CHECKPOINT: 1. Verify the length of the coaxial cable (not more than 1.4km) connected between the two VC-232G units. Please also try to adjust the DIP switch of the VC-232G to the other SNR mode. 2. Please note you must use one VC-232G in CO mode and the other VC-232G in CPE mode to make connection to each other work. SYMPTOM: TP LED does not light after cable is connected to the port.
8. FAQs Q1: What is VDSL2? A1: VDSL2 (Very High-Bit-Rate Digital Subscriber Line 2), G.993.2 is the newest and most advanced standard of xDSL broadband wire line communications. Designed to support the wide deployment of Triple Play services such as voice, data, high definition television (HDTV) and interactive gaming, VDSL2 enables operators and carrier to gradually, flexibly, and cost efficiently upgrade the existing xDSL-infrastructure.
9. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ: http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address: support@planet.com.tw Copyright © PLANET Technology Corp. 2017. Contents are subject to revision without prior notice.
EC Declaration of Conformity For the following equipment: *Type of Product: 1-Port 10/100/1000T Ethernet to VDSL2 Converter *Model Number: VC-232G * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.
