SGS-6341-Series User Manual
Table Of Contents
- Chapter 1 INTRODUCTION
- Chapter 2 INSTALLATION
- Chapter 3 Switch Management
- Chapter 4 Basic Switch Configuration
- Chapter 5 File System Operations
- Chapter 6 Cluster Configuration
- Chapter 7 Port Configuration
- Chapter 8 Port Isolation Function Configuration
- Chapter 9 Port Loopback Detection Function Configuration
- Chapter 10 ULDP Function Configuration
- Chapter 11 LLDP Function Operation Configuration
- Chapter 12 Port Channel Configuration
- Chapter 13 MTU Configuration
- Chapter 14 EFM OAM Configuration
- Chapter 15 PORT SECURITY
- Chapter 16 DDM Configuration
- Chapter 17 LLDP-MED
- Chapter 18 bpdu-tunnel Configuration
- Chapter 19 EEE Energy-saving Configuration
- Chapter 20 VLAN Configuration
- Chapter 21 MAC Table Configuration
- Chapter 22 MSTP Configuration
- Chapter 23 QoS Configuration
- Chapter 24 Flow-based Redirection
- Chapter 25 Flexible Q-in-Q Configuration
- Chapter 26 Layer 3 Management Configuration
- Chapter 27 ARP Scanning Prevention Function Configuration
- Chapter 28 Prevent ARP Spoofing Configuration
- Chapter 29 ARP GUARD Configuration
- Chapter 30 Gratuitous ARP Configuration
- Chapter 31 DHCP Configuration
- Chapter 32 DHCPv6 Configuration
- Chapter 33 DHCP Option 82 Configuration
- Chapter 34 DHCP Option 60 and option 43
- Chapter 35 DHCPv6 Options 37, 38
- Chapter 36 DHCP Snooping Configuration
- Chapter 37 DHCP Snooping Option 82 Configuration
- Chapter 38 IPv4 Multicast Protocol
- Chapter 39 IPv6 Multicast Protocol
- Chapter 40 Multicast VLAN
- Chapter 41 ACL Configuration
- Chapter 42 802.1x Configuration
- 42.1 Introduction to 802.1x
- 42.2 802.1x Configuration Task List
- 42.3 802.1x Application Example
- 42.4 802.1x Troubleshooting
- Chapter 43 The Number Limitation Function of MAC and IP in Port, VLAN Configuration
- Chapter 44 Operational Configuration of AM Function
- Chapter 45 Security Feature Configuration
- 45.1 Introduction to Security Feature
- 45.2 Security Feature Configuration
- 45.2.1 Prevent IP Spoofing Function Configuration Task Sequence
- 45.2.2 Prevent TCP Unauthorized Label Attack Function Configuration Task Sequence
- 45.2.3 Anti Port Cheat Function Configuration Task Sequence
- 45.2.4 Prevent TCP Fragment Attack Function Configuration Task Sequence
- 45.2.5 Prevent ICMP Fragment Attack Function Configuration Task Sequence
- 45.3 Security Feature Example
- Chapter 46 TACACS+ Configuration
- Chapter 47 RADIUS Configuration
- Chapter 48 SSL Configuration
- Chapter 49 IPv6 Security RA Configuration
- Chapter 50 MAB Configuration
- Chapter 51 PPPoE Intermediate Agent Configuration
- Chapter 52 Web Portal Configuration
- Chapter 53 VLAN-ACL Configuration
- Chapter 54 SAVI Configuration
- Chapter 55 MRPP Configuration
- Chapter 56 ULPP Configuration
- Chapter 57 ULSM Configuration
- Chapter 58 Mirror Configuration
- Chapter 59 sFlow Configuration
- Chapter 60 RSPAN Configuration
- Chapter 61 ERSPAN
- Chapter 62 SNTP Configuration
- Chapter 63 NTP Function Configuration
- Chapter 64 Summer Time Configuration
- Chapter 65 DNSv4/v6 Configuration
- Chapter 66 Monitor and Debug
- Chapter 67 Reload Switch after Specified Time
- Chapter 68 Debugging and Diagnosis for Packets Received and Sent by CPU
- Chapter 69 Dying Gasp Configuration
- Chapter 70 PoE Configuration
[no] access-list <6000-7999> {deny|permit} ip
{{<source> <source-wildcard>}|{host-source
<source-host-ip>{range<2-65535>|}}|any-sou
rce} {{<destination>
<destination-wildcard>}|{host-destination
<destination-host-ip>{range<2-255>|}}|any-d
estination}
The rule used to configure destination
control. This rule does not take effect
until it is applied to source IP or
VLAN-MAC and port. Using the NO
form of it can delete specified rule.
The last is to configure the rule to specified source IP, source VLAN MAC or specified port. It is
noticeable that, due to the above situations, these rules can only be used globally in enabling
IGMP-SNOOPING. And if IGMP-SNOOPING is not enabled, then only source IP rule can be
used under IGMP Protocol. The configuration commands are as follows:
Command Explanation
Port Mode
[no] ip multicast destination-control
access-group <6000-7999>
Used to configure the rules destination
control uses to port, the NO form
cancels the configuration.
Global Mode
[no] ip multicast destination-control
<1-4094> <macaddr> access-group
<6000-7999>
Used to configure the rules destination
control uses to specify VLAN-MAC, the
NO form cancels the configuration.
[no] ip multicast destination-control
<IPADDRESS/M> access-group
<6000-7999>
Used to configure the rules destination
control uses to specified IP address/net
mask, the NO form cancels the
configuration.
3. Multicast Strategy Configuration
Multicast Strategy uses the manner of specifying priority for specified multicast data to achieve
and guarantee the effects the specific user requires. It is noticeable that multicast data can not
get a special care all along unless the data are transmitted at TRUNK port. The configuration is
very simple, it has only one command, i.e. to set priority for the specified multicast. The
commands are as follows:
Command Explanation
Global Mode
[no] ip multicast policy <IPADDRESS/M>
<IPADDRESS/M> cos <priority>
Configure multicast strategy, specify
priority for sources and groups in
specific range, and the range is <0-7>.
38-31
User’s Manual of SGS-6341 series