User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 System Information
- 4.2 Switch Management
- 4.2.1 Jumbo Frame
- 4.2.2 Interface
- 4.2.3 Statistics
- 4.2.4 VLAN
- 4.2.5 MAC Address
- 4.2.6 Port Mirror
- 4.2.7 Static Link Aggregation
- 4.2.8 LACP
- 4.2.9 Trunk Group Load Balance
- 4.2.10 Spanning Tree Protocol
- 4.2.11 IGMP Snooping
- 4.2.12 IGMP Filtering and Throttling
- 4.2.13 MLD Snooping
- 4.2.14 MVR For IPv4
- 4.2.14.1 Configure Global
- 4.2.14.2 Configure Domain
- 4.2.14.3 Show Configure Profile
- 4.2.14.4 Add Configure Profile
- 4.2.14.5 Show Associate Profile
- 4.2.14.6 Add Associate Profile
- 4.2.14.7 Configure Interface
- 4.2.14.8 Show Static Group Member
- 4.2.14.9 Add Static Group Member
- 4.2.14.10 Show Member
- 4.2.14.11 Show Query Statistics
- 4.2.14.12 Show VLAN Statistics
- 4.2.14.13 Show Port Statistics
- 4.2.14.14 Show Group Statistics
- 4.2.15 MVR For IPv6
- 4.2.15.1 Configure Global
- 4.2.15.2 Configure Domain
- 4.2.15.3 Show Configure Profile
- 4.2.15.4 Add Configure Profile
- 4.2.15.5 Show Associate Profile
- 4.2.15.6 Add Associate Profile
- 4.2.15.7 Configure Interface
- 4.2.15.8 Show Static Group Member
- 4.2.15.9 Add Static Group Member
- 4.2.15.10 Show Member
- 4.2.15.11 Show Query Statistics
- 4.2.15.12 Show VLAN Statistics
- 4.2.15.13 Show Port Statistics
- 4.2.15.14 Show Group Statistics
- 4.2.16 LLDP
- 4.2.17 ERPS
- 4.2.18 Loopback Detection
- 4.2.19 UDLD
- 4.2.20 Rate Limit
- 4.2.21 Storm Control
- 4.2.22 Stacking
- 4.2.23 Pepo
- 4.3 Route Management
- 4.4 ACL
- 4.5 CoS
- 4.6 Qu’s
- 4.7 Security
- 4.7.1 AAA
- 4.7.2 Web Authentication
- 4.7.3 802.1X
- 4.7.4 MAC Authentication
- 4.7.5 HTTPS
- 4.7.6 SSH
- 4.7.7 Port Security
- 4.7.8 DAI – Dynamic ARP Inspection
- 4.7.9 Login IP Management
- 4.7.10 DoS Protection
- 4.7.11 IPv4 DHCP Snooping
- 4.7.12 IPv6 DHCP Snooping
- 4.7.13 IPv4 Source Guard
- 4.7.14 IPv6 Source Guard
- 4.7.15 Application Filter
- 4.7.16 CPU Guard
- 4.8 Device Management
- 4.8.1 SNMP
- 4.8.2 RMON
- 4.8.3 Cluster
- 4.8.4 DNS
- 4.8.5 DHCP
- 4.8.6 OAM
- 4.8.7 CFM
- 4.8.7.1 Global Configuration
- 4.8.7.2 Interface Configuration
- 4.8.7.3 MD Management
- 4.8.7.4 MD Details
- 4.8.7.5 MA Management
- 4.8.7.6 MA Details
- 4.8.7.7 MEP Management
- 4.8.7.8 Remote MEP Management
- 4.8.7.9 Transmit Link Trace
- 4.8.7.10 Transmit Loopback
- 4.8.7.11 Transmit Delay Measure
- 4.8.7.12 Show Local MEP
- 4.8.7.13 Show Local MEP Details
- 4.8.7.14 Show Local MIP
- 4.8.7.15 Show Remote MEP
- 4.8.7.16 Show Remote MEP Details
- 4.8.7.17 Show Link Trace Cache
- 4.8.7.18 Show Fault Notification Generator
- 4.8.7.19 Show Continuity Check Error
- 4.8.8 Time Setting
- 4.8.9 Event Log
- 4.8.10 File Management
- 4.8.11 Ping
- 4.8.12 Trace Route
- 4.8.13 System Reboot
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of SGS-5240 Series Managed Switch
248
4.8.1.6 Remote User
Device Management > SNMP > Remote User page is used to identify the source of SNMPv3 inform messages sent from the
local switch. Each SNMPv3 user is defined by a unique name. Users must be configured with a specific security level and
assigned to a group. The SNMPv3 group restricts users to a specific read, write, and notify view.
User Name – The name of user connecting to the SNMP agent. (Range: 1-32 characters)
Group Name – The name of the SNMP group to which the user is assigned. (Range: 1-32 characters)
Remote IP – The Internet address of the remote device where the user resides.
Security Model – The user security model; SNMP v1, v2c or v3. (Default: v3)
Security Level – The following security levels are only used for the groups assigned to the SNMP security model:
noAuthNoPriv – There is no authentication or encryption used in SNMP communications. (This is the default
security level.)
AuthNoPriv – SNMP communications use authentication, but the data is not encrypted.
AuthPriv – SNMP communications use both authentication and encryption.
Authentication Protocol – The method used for user authentication. (Options: MD5, SHA; Default: MD5)
Authentication Password – A minimum of eight plain text characters is required.
Privacy Protocol – The encryption algorithm use for data privacy; only 56-bit DES is currently available.
Privacy Password – A minimum of eight plain text characters is required.
4.8.1.7 Trap
Device Management > SNMP > Trap is used page to specify the host devices to be sent traps and the types of traps to send.
SNMP Version 1
IP Address – IP address of a new management station to receive notification message (i.e., the targeted recipient).
Version – Specifies whether to send notifications as SNMP v1, v2c, or v3 traps. (Default: v1)
Community String – Specifies a valid community string for the new trap manager entry. (Range: 1-32 characters, case
sensitive) Although you can set this string in the Configure Trap – Add page, we recommend defining it in the Configure
User – Add Community page.
UDP Port – Specifies the UDP port number used by the trap manager. (Default: 162) SNMP Version 2c
IP Address – IP address of a new management station to receive notification message (i.e., the targeted recipient).
Version – Specifies whether to send notifications as SNMP v1, v2c, or v3 traps.
Notification Type
Traps – Notifications are sent as trap messages.