User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 1-port IEEE 802.3bt PoE++ to
4-port IEEE 802.3af/at Gigabit PoE Extender, POE-E304. “Gigabit PoE
Extender” mentioned in this manual refers to the POE-E304.
Open the box of the Gigabit PoE Extender and carefully unpack it. The
box should contain the following items:
Gigabit PoE Extender x 1
User’s Manual x 1 Rubber Feet x 4
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
 Automatic address learning and address aging
 Case and Installation
 No external power cable installation required
 Made of metal, desktop size design
 Wall-mountable, Plug-and-Play installation
 0 ~ 50 degrees C operating Temperature
Note
PSE (power sourcing equipment) is a device (switch or
hub for instance) that will provide power in a PoE setup.
The maximum allowed continuous output power per such
device in IEEE 802.3af is 15.4 watts and in IEEE 802.3at
is 30 watts.
PD (powered device) such as IP phone, network
camera or wireless access point is a PoE-enabled terminal
that consumes energy supplied by PSE.
3.ProductSpecications
Model POE-E304
Hardware Specications
Network
Connector
PoE In Port
1 x 10/100/1000BASE-T Ethernet with IEEE 802.3bt
PoE++ “Data + DC” in, auto MDI/MDI-X, auto-
negotiation RJ45 connector
PoE Out Port
4 x 10/100/1000BASE-T Ethernet with IEEE
802.3af/802.3at PoE “Data + DC” out, auto MDI/
MDI-X, auto-negotiation RJ45 connector
4. Hardware Introduction
4.1 Three-View Diagram
The three-view diagram of the Gigabit PoE Extender consists of one
auto-sensing 10/100/1000BASE-T 802.3bt PoE In port, and four auto-
sensing 10/100/1000BASE-T 802.3af/802.3at PoE Out ports. The LED
Indicators are also located on the port of Gigabit PoE Extender front
panel.
168
94
32
122
50-56V
5PWR41 2
PoE In
3
PoE Out
PoE-in-Use
LNK ACT
10/100/1000
POE-E304
Power
Requirements
PoE In: IEEE 802.3bt or 4-pair 802.3at PoE+
compliant with voltage within 50-56V DC
External DC: 50~56V DC
Power
Consumption
0.9 watts/3.1BTU (System on)
74 watts/252.4BTU (Full loading with PoE function)
Network Cable
10BASE-T: 4-pair UTP Cat5 up to 100m (328ft)
100BASE-TX: 4-pair UTP Cat5 up to 100m (328ft)
1000BASE-T: 4-pair UTP Cat5e, 6, up to 100m (328ft)
EIA/TIA-568 100-ohm STP (100m, 328ft)
Power over Ethernet
PoE Standard
PoE In Port
IEEE 802.3bt Power over Ethernet Plus Plus end-
span and mid-span PD class 4 PD
Per PoE Out Port
IEEE 802.3at Power over Ethernet Plus end-span
PSE
IEEE 802.3af Power over Ethernet end-span PSE
PoE Power
PoE In Port
50~56V DC, max. 95 watts input
Per PoE Out Port
50~55V DC, max. 32 watts output
Power Pin
Assignment
PoE In Port
1/2 (-), 3/6 (+); 4/5 (+), 7/8 (-)
Per PoE Out Port
1/2 (-), 3/6 (+), end-span (Type A)
PoE Power
Budget
65 watts (max.) @ IEEE 802.3bt PoE++ Type 4 PSE
input
32 watts (max.) @ IEEE 802.3at PoE+ PSE input
2. Product Features
 Physical Port
 5 10/100/1000BASE-T Gigabit RJ45 interfaces
- 1-port data + power input
- 4-port data + power output
 Power over Ethernet
 1-port data + power input
- Complies with IEEE 802.3bt PoE++ PD
- Supports PoE input power up to 95 watts
 4-port data + power output
- Complies with IEEE 802.3af/IEEE 802.3at PoE+/end-span PSE
- Up to 4 IEEE 802.3af/802.3at devices powered
- Supports PoE power up to 32 watts for each PoE port
- Auto detects powered device (PD)
 Extends the range of PoE to an additional 100 meters (328ft.)
 Forwards both Ethernet data and PoE power to remote device
 Layer 2 Features
 Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/
MDI-X
 Integrates address look-up engine, supporting 2K absolute MAC
addresses
 9K jumbo packet support
 Features Store-and-Forward mode with wire-speed ltering and
forwarding rates
 IEEE 802.3x ow control for full duplex operation and backpressure
for half duplex operation
Standard Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Standard
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
IEEE 802.3x Flow Control
Environment
Operating
Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage
Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Note
The maximum distance that data and power can transmit
depends on the quality of the UTP cable and environment.
4.2 Ports Connection
PoE IN Port
Connect the PoE IN port from the following 802.3bt
PoE++ PSE devices through a Cat5/5e/6 UTP cable:
 802.3bt PoE++/UPOE/PoH injector
 802.3bt PoE++/UPOE/PoH injector hub
 802.3bt PoE++/UPOE/PoH Ethernet switch
PoE OUT Port
Connect the PoE OUT port to the following 802.3at/af
PD devices through a Cat5/5e/6 UTP cable:
 PoE IP camera
 PoE VoIP phone
 PoE wireless AP
 PoE splitter
4.3 LED Indicators
 802.3bt PoE IN Port
LED Color Function
10/100/1000
LNK/ACT
Green
Lights to indicate the link through that
port is successfully established at
10/100/1000Mbps.
Blinks to indicate that the port is actively
sending or receiving data.
Data Rate 10/100/1000Mbps
Switch
Architecture
Store-and-Forward
MAC Address
Table
2K
Data Buer 1Mbits
Switch Fabric 10Gbps
Switch
Throughput
7.44Mpps @ 64 bytes
Jumbo Frame 9K
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
LED Indicators
PoE In Port
10/100/1000 LNK/ACT (green)
PoE Out Port 1 to Port 4
10/100/1000 LNK/ACT (green)
PoE-in-Use (orange)
PWR (orange)
Protection
ESD: Contact 4KV, Air 6KV
Surge: 4KV
Enclosure Metal
Installation Desktop/Wall mountable
Dimensions
(W x D x H)
168 x 93 x 32mm
Weight 403g