User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
802.3at/af PoE Out Ports
LED Color Function
PoE-in-Use Orange
Lights to indicate the port is providing
52V-56V DC in-line power output.
10/100/1000
LNK/ACT
Green
Lights to indicate the link through
that port is successfully established at
10/100/1000Mbps.
Blinks to indicate that the port is actively
sending or receiving data.
5. Hardware Installation
5.1 Before Installation
The POE-E202 is installed between the PSE (Power Source
Equipment) and the PD (Powered Device); it is powered by PSE and
forwards the Ethernet data and remaining POE power to the PD.
The POE-E202 doesn’t require an external power supply and it can
be installed easily by just plug and play without affecting the data
transmission performance.
Note
1. To provide you with better PoE power and data
extension quality, we strongly recommend that
you use “Solid UTP Cable” when installing the
POE-E202.
2. The POE-E202 can be installed with a third-party
device if the device complies with IEEE 802.3at/af
standard.
Note
1. When the PoE-in-use LED turns steady orange, it
means the Gigabit PoE Extender is being powered
successfully with PoE.
2. If the PoE-in-use LED is not lit, please check the
remote PSE or the cable connecting to a PC or a
network device to see if the cable is correct. Or
with an 802.3at device such as the target PD,
check whether the power injection is correct.
Never connect any non-standard POE PSE to the
Gigabit PoE Extender; it will damage the device
permanently.
5.3 Connecting POE-E202 to Powered Device (PD)
Step 1: Connect the additional Cat5e/6 cable that will be used
to connect to the remote Powered Device (PD) to the
“PoE Out” port of the Gigabit PoE Extender.
PoE Wireless AP
UTP
UTP
PoE Camera
POE-E202
PoE OUT PoE IN
10/100/1000T
PoE Extender
1 2
ACTLNK
PoE In-use
PSE 802.3at PoE Switch
UTP
PoE
PoE
PoE
5.2 Connecting POE-E202 to Power Source
Equipment (PSE)
This section describes how to install Gigabit PoE Extender and make
connection to it. Please read the following topics and perform the
procedures in the order being presented.
There are 3 RJ45 ports in the Gigabit PoE Extender, of which the
“PoE IN” port functions as “PoE (Data and Power) input” and
the two “PoE Out” ports function as “PoE (Data and Power)
output”.
Step 1: Connect a standard Cat5e/6 UTP cable from power
source equipment (PSE), such as PoE switch, PoE
injector hub and single port PoE injector, to the “PoE IN”
port of the Gigabit PoE Extender.
PSE 802.3at PoE Switch
POE-E202
PoE OUT PoE IN
10/100/1000T
PoE Extender
1 2
ACTLNK
PoE In-use
UTP
PoE
Step 2: The PSE delivers both Ethernet Data and PoE power
over UTP cable to the Gigabit PoE Extender and the
“PoE-in-use” and “LNK/ACT LED” will be lit steadily.
Step 2: The “PoE Out” port is also the power injector which
transmits DC voltage to the Cat5e/6 cable and transfer
data and power simultaneously between the PSE and PD.
Step 3: Once the Gigabit PoE Extender detects the existence of an
IEEE 802.3at/af device, the “PoE-in-Use” LED indicator
will be lit steadily, showing it is providing power.
Note
1. If the connected device is not fully complying with
IEEE 802.3af/at standard or in-line power device,
the PoE-in-Use LED indicator of the Gigabit PoE
Extender will not be lit steadily.
2. According to IEEE 802.3af/at standard, the Gigabit
PoE Extender will not inject power to the cable
if not connected to a standard IEEE 802.3af/at
device.
5.4 PoE Power Distribution
The POE-E202 can obtain a maximum of 36-watt PoE power from
802.3at PoE input port and supplies a maximum of 30-watt PoE
power budget to 2 PoE output ports, extending both the reach of
Gigabit Ethernet Data and IEEE 802.3at/802.3af Power over
Ethernet over the standard 100m (328 ft.) Cat 5/5e/6 UTP cable to
up to 200m at the same time.
PoE Dome IP Camera
PoE+
(
30W
)
IEEE 802.3af
(
12W
)
Power
Data
100m
100m
IEEE 802.3af
(
12W
)
100m
PoE PTZ IP Camera
PoE+
(
30W
)
IEEE 802.3at
(
25W
)
25W
12W+12W
Power
Data
100m
PoE Injector/Switch
802.3at PoE Extender
802.3at PoE Extender
PoE Injector/Switch
100m
1 In 1 Out
1 In 2 Out
PoE Dome IP Camera
PoE+
(
30W
)
IEEE 802.3af
(
12W
)
Power
Data
100m
100m
IEEE 802.3af
(
12W
)
100m
PoE PTZ IP Camera
PoE+
(
30W
)
IEEE 802.3at
(
25W
)
25W
12W+12W
Power
Data
100m
PoE Injector/Switch
802.3at PoE Extender
802.3at PoE Extender
PoE Injector/Switch
100m
1 In 1 Out
1 In 2 Out
6. Power over Ethernet Capability
With different distance and different PoE input source, it will inect
the PoE output capability. Please refer to the table below.
PSE 802.3at PoE Switch
POE-E202
PoE Output Capacity
(A)(B)(C)
(A): Distance
(B): Distance
(C): Watts
6.1 When PSE/PoE Switch output is DC 52V
A (Distance) B (Distance) C (Watts)
100M 20M 21.6
100M 60M 20.7
100M 100M 19.7
6.2 When PSE/PoE Switch output is DC 56V
A (Distance) B (Distance) C (Watts)
100M 20M 21.1
100M 60M 20.2
100M 100M 19.3
7. Customer Support
Thank you for purchasing PLANET products. You can browse our
online FAQ resource at PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2016.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners