User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
4.5 Wall-mount Installation
To install the POE-E201 on the wall, please follow the instructions
described below.
Step 1: Find the wall that you want to mount the POE-E201 on.
Step 2: Refer to the picture below to screw the two screws on the
wall. The distance between the 2 screws is 46.7mm and
the line through them must be horizontal
46.70
4.00
�7.00
Step 3: Hang the POE-E201 on the screws from the wall.
4.6 Optional - DIN-rail Mounting
There are two DIN-rail holes on the left side of the POE-E201
that allows it to be easily mounted on the DIN rail. If the DIN-rail
mounting is opted, the DIN-rail mounting kit (RKE-DIN) has to be
ordered as it is not included in the package. The following steps for
DIN-rail mounting are shown below:
Caution
You must use the screws supplied with the mounting
brackets. Damage caused to the parts by using
incorrect screws would invalidate your warranty.
5.ProductSpecications
Model POE-E201
Interfaces
LAN IN
1 x 10/100/1000BASE-T Ethernet with IEEE
802.3at/802.3af PoE “Data + DC” in
Auto MDI/MDI-X, auto-negotiation RJ45 connector
LAN OUT
1 x 10/100/1000BASE-T Ethernet with IEEE
802.3at/802.3af PoE “Data + DC” out
Auto MDI/MDI-X, auto-negotiation RJ45 connector
Power over Ethernet
PoE Standard
IEEE 802.3at Power over Ethernet Plus
Backward compatible with IEEE 802.3af Power
over Ethernet
PoE Power
Supply Type
End-span/Type A
Power Pin
Assignment
1/2 (+), 3/6 (-)
PoE Power
Output
44~52V DC, 510mA; max. 26 watts
Step 1: Screw the DIN-rail bracket on the POE-E201.
Step 2: First put the upper DIN-rail bracket on to the rail shown
below and then the lower bracket on to the rail to nish
the mounting.
1
2
Step 3: Make sure the POE-E201 unit is tightly xed on the track.
Maximum
Distance
500 meters with daisy-chain installation of 4
units (Refer to section 4.4)
Hardware Specications
Data Rate 10/100/1000Mbps
Switch
Architecture
Store-and-Forward
Switch
Throughput
10Mbps: 14880pps@64Bytes
100Mbps: 148810pps@64Bytes
1000Mbps: 1488000pps@64Bytes
Maximum
Frame Size
9K bytes
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
LED Indicators
• 1x PoE IN (Green)
• 1 x LAN Data (Green)
• 1 x PoE OUT (Amber)
Protection
ESD (Ethernet): 2KV
Surge (EFT for power): 2KV
Dimensions
(W x D x H)
94 x 70 x 26 mm
Weight 189g
Power
Requirements
IEEE 802.3at PoE+ compliant with voltage within
52~56V DC
IEEE 802.3af PoE compliant with voltage within
48~51V DC
System Power
Consumption
2.6 watts (System on)
Case Metal
Installation Wall or DIN-rail mounting
Network Cable*
10BASE-T: 4-pair UTP Cat. 5 up to 100m (328ft)
100BASE-TX: 4-pair UTP Cat. 5 up to 100m
(328ft)
1000BASE-T: 4-pair UTP Cat. 5e, 6, 7 up to
100m (328ft)
EIA/TIA-568 100-ohm STP (100m or 328ft)
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Standard
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3x Flow Control
Environment
Temperature
Operating: -10~60 degrees C
Storage: -40~85 degrees C
Humidity
Operating: 5% to 95%,
Storage: 5% to 95% (non-condensing)
* Remarks :
The actual distance of 100 meters could not measure up owing
to voltage drop on the wire. In addition, the distance can be
compromised based on the quality of the UTP cable and environment.
6. Customer Support
Thank you for purchasing PLANET products. You can browse our
online FAQ resource on PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET support team.
PLANET online FAQs :
http://www.planet.com.tw/en/support/faq
Support team mail address :
[e-mail]
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.