(V3) User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
The ground cabling procedure is as follows:
Step 1： Remove the nuts from the rear PoE Injector where the
grounding posts are.
Step 2： Wrap one end of the green and yellow grounding cables
to the grounding posts.
Step 3： Tighten the grounding post nut well.
Step 4： Attach the other end of the grounding cable to the
grounding connector.
Note
The grounding cable should be made of a good
conductor, and the diameter should be determined by
the possible maximum current that may pass through.
Bare conductor cabling is forbidden.
Ground resistance value: The combined grounding
resistance should be less than 1 ohm.
5.2 Before Installation
Before your installation, it is recommended to check your network
environment. If there is any IEEE 802.3bt device that needs to be
powered on and works normally, the POE-175-95 provides you with
a way out to supply power to this Ethernet device conveniently and
easily.
5.4 POE-175-95 Installation
1. Connect the AC power cord to the “AC slot” of the POE-175-95;
the “PWR” LED will be steadily on.
2. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to the “Ethernet” port of the POE-175-95.
3. Connect the long cable to the “Ethernet+DC” port.
4. Due to the capability of IEEE 802.3af/at/bt Power over Ethernet,
the POE-175-95 can directly connect with any IEEE 802.3af/at/
bt-compliant end nodes, such as PTZ (pan, tilt, zoom) network
cameras, color touch screen Voice over IP (VoIP) telephones and
multi-channel wireless LAN access points.
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE
PoE
++/UPoE
PTZ
IP Camera
Ethernet Switch
Data
Power
Power
Data
95 watts
95 watts
100 meters
802.3bt PoE
++
Injector
POE-175-95
Figure 2: Architecture of connected IEEE 802.3af/at/bt devicea
Once the POE-175-95 detects the existence of an IEEE 802.3af/at/
bt device, the PoE-in-Use LED indicator will be steadily on to show
it is providing power.
Note
1. According to IEEE 802.3af/at/bt Power over
Ethernet, the POE-175-95 will not inject power to
the cable if not connected to IEEE 802.3af/at/bt-
compliant device.
2. Depending on the length of cable, the PoE power
received by a PD is different.
It is equipped with an AC power cord with 100-240V AC input and
injects DC 54V power into the pin of the twisted-pair cable (pair
1/2 [-], 3/6 [+] and pair 4/5 [+], 7/8 [-]).
5.3 Selectable Standard IEEE 802.3bt, UPoE or
Legacy mode
The POE-175-95 provides power to those powered devices which
do not fully follow the IEEE 802.3af/at/bt standard. The UPoE and
Legacy bt modes provide the PD with 60 to 95 watts of power
output voltage.
Modes Descriptions
BT mode
Powered devices that fully support IEEE 802.3bt
standards with output budget of 90W.
UPoE mode
Powered devices that support Cisco UPoE with
output budget of 95W.
Legacy BT
Powered devices that support capacitive or
resistance electronic tag with output budget of 90W.
10/100/1000T
EthernetEthernet+DC
PWR
PoE-in-Use
PoE Max.
POE-175-95
802.3bt PoE++ Injector
BTLegacy BT UPoE
5.5 POE-175-95 and POE-173S Installation
1. Connect DC plug from "DC Out" of the POE-173S to a remote
device.
2. Connect the AC power cord to the “AC slot” of the POE-175-95;
the “PWR” LED will be steadily on.
3. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to the “Ethernet” port of the POE-175-95.
4. Connect a standard Ethernet cable from “Ethernet+DC” port
of the POE-175-95 to the “PoE In” port of the POE-173S. The
“30W”, “60W” or “90W+” LED of the POE-173S and the
“PoE-in-Use” LED of the POE-175-95 will light up continuously.
5. Connect a standard Ethernet cable from the “Ethernet” port of
the POE-173S to the remote Ethernet device.
6. The remote device will be turned on and connected.
95 watts
95 watts
12V/19V/24V
Power
Data
PoE
Power
Data
DC
Digital
Signage
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
DC
Power Line (DC)
802.3bt PoE
++
Splitter
POE-173S
Ethernet Switch
Data
Power
100 meters
802.3bt PoE
++
Injector
POE-175-95
Figure 3: Architecture of connected POE-175-95 and POE-173S
Note
Please ensure the POE-173S output voltage is correct
before applying power to the remote device.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : Single-Port 10/100/1000Mbps 802.3bt PoE Injector
*Model Number : POE-175-95
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on
2014/30/EU and Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 2015+AC:2016, CLASS A
EN 61000-3-2 2014
EN 61000-3-3 2013
EN 55024 2010+A1:2015
EN 62368-1 2014
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
Person responsible for making this declaration
Name, Surname Jonas Yang
Position / Title : Director
Taiwan
8
th
Jan., 2019
.
Place
Date
Legal Signature
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site rst to check if
it could solve your issue. If you need more support information,
please contact PLANET support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq?method=category&c1=2
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2022
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.