POE-171A-Series (V3) User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Monitoring of power usage of POE-171A-60:
LED Description
20W
1. O to indicate the PoE usage is less than 9W.
2. Blinks to indicate that the PoE usage is around 10W to
19W.
3. Lights to indicate the PoE usage is more than 20W.
40W
1. Blinks to indicate that the PoE usage is around 30W to
39W.
2. Lights to indicate the PoE usage is more than 40W.
60W+
1. Blinks to indicate that the PoE usage is around 50W to
59W.
2. Lights to indicate the PoE usage is maximum.
Monitoring of power usage of POE-171A-95:
LED Description
30W
1.O to indicate the PoE usage is less than 14W.
2. Blinks to indicate that the PoE usage is around 15W to
29W.
3. Lights to indicate the PoE usage is more than 30W.
60W
1.Blinks to indicate that the PoE usage is around 45W to
59W.
2. Lights to indicate the PoE usage is more than 60W.
90W+
1.Blinks to indicate that the PoE usage is around 75W to
89W.
2. Lights to indicate the PoE usage is maximum.
5. Hardware Installation
The following section describes the hardware installation of the
POE-171A series. Before connecting any network device to it,
please read this chapter carefully.
5.1 Before Installation
Before your installation, it is recommended to check your network
environment. If there is any IEEE 802.3bt device that needs to be
powered on and works normally, the POE-171A series provides you
with a way out to supply power to this Ethernet device conveniently
and easily. The POE-171A series is equipped with a power adaptor
which is 100-240V AC input and injects DC 52~56V power into the
pin of the twisted pair cable (pair 1/2 [-], 3/6 [+] and pair 4/5
[+], 7/8 [-]).
5.2 POE-171A series Installation
1. Connect the AC power adaptor to the “52-56V DC IN” of the
POE-171A series; the “PWR” LED will be steadily on.
2. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to the “Ethernet” port of the POE-171A series.
3. Connect the long cable to the “Ethernet+DC” port of the POE-
171A series and the IEEE 802.3af/at/bt PD.
4. The POE-171A series, adopting the IEEE 802.3af/at/bt tech-
nology, can directly connect with any IEEE 802.3af/at/bt end-
nodes, such as PTZ (pan, tilt & zoom) network cameras, PTZ
speed dome cameras, color touch screen, Voice over IP (VoIP)
telephones and multi-channel wireless LAN access points as the
screen in Figure 3 is shown below.
PoE Mode:
PoE Mode Description
Standard Fully conforms to the IEEE 802.3af/at/bt standard.
Legacy
The legacy detection is to identify the valid current
signature of the PDs that do not fully follow the IEEE
802.3af/at/bt standard. This protects against damage
to the PDs as the right PoE mode is applied.
Force
If the output power of injector is less than 1 watt
when it works as Legacy mode, after 20 seconds, the
Force mode will be enabled.
When the Force mode is enabled, it will provide PD
with max. 60W.
If the output power of injector is less than 1 watt
when it works as Force mode, after 2 seconds, the
Legacy mode will be enabled.
Note
1. After adjusting the DIP switch, the PoE port will
stop and then work again.
2. Before connecting the Ethernet+DC port to network
device, please make sure that it accepts PoE input
to prevent damage.
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE
Power
Data
PoE PTZ
IP Camera
100 meters
802.3bt PoE Injector
POE-171A-60
Switch
Data
Power
AC-to-DC Adapter
110-240V AC
Figure 3: Architecture of Connected IEEE 802.3af/at/bt Devices
Once the POE-171A series detects the existence of an IEEE
802.3af/at/bt device, the PoE-in-Use LED indicator will be steadily
on to show it is providing power.
Note
Since the PoE port of the POE-171A series supports
52-56V DC PoE power output, please check and
assure the PD accepts DC power range of 52-56V DC.
Otherwise, it will damage the PD.
6. Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site rst to check if
it could solve your issue. If you need more support information,
please contact PLANET support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq?method=category&c1=2
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2019.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
FCC Warning
This device has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the Instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
WEEE Warning
To avoid the potential eects on the environment and
human health as a result of the presence of hazardous
substances in electrical and electronic equipment, end
users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do
not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.