User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
Note
The 802.3at PoE+ Injector and POE-162S
can be installed in pair. However, the
use of third-party device is allowed if the
device complies with IEEE 802.3at Power
over Ethernet.
The 802.3at PoE+ Injector Installation
1. Connect the AC power cord to the “AC slot” of the
802.3at PoE+ Injector; the “POWER” LED will be
steadily on.
2. Connect a standard network cable from a switch/
workstation to the “LAN” port of the 802.3at PoE+
Injector.
3. And connect the Injector to a remote device like a
PoE PTZ IP camera over the UTP cable.
** The 802.3at PoE+ Injector can directly connect with
any IEEE 802.3at/802.3af end-nodes, such as PTZ
IP and speed dome cameras, color touch-screen
Voice over IP (VoIP) telephones, multi-channel wire-
less LAN access points, etc. The installation is shown
in Figure 3 below.
Switch
100 meters
PoE
Power
Data
PoE PTZ
IP Camera
802.3at PoE Injector
Power
Data
AC
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line (AC)
AC
Figure 3: Connection to IEEE 802.3at/802.3af Devices
When the 802.3at PoE+ Injector detects the existence
of an IEEE 802.3at/802.3af device, the ACTIVE LED
indicator will be steadily on to show it is providing
power.
Note
1. Since the 802.3at PoE+ Injector PoE port
supports 50-54V DC PoE power output,
please check and assure the powered
device’s (PD) acceptable DC power range
is 50-54V DC. Otherwise, it will damage
the PD.
2. If the connected device is not fully
complying with IEEE 802.3at/802.3af
Power over Ethernet or in-line power
device, the LED indicator of the 802.3at
PoE+ Injector will not be steadily on.
The 802.3at PoE+ Injector and POE-162S, the
IEEE 802.3at Injector Splitter Installation
1. Connect the AC power cord to “AC slot” of the
802.3at PoE+ Injector; the “POWER” LED will be
steadily on.
2. Connect a standard network cable from the “POE”
port of the 802.3at PoE+ Injector to the “PoE In”
port of the POE-162S. The “ACTIVE” LED of the
802.3at PoE+ Injector and PoE-in-use LED of the
POE-162S will continue to be lit.
3. Connect a standard network cable from a switch/
workstation to the “LAN” port of the 802.3at PoE+
Injector.
4. Connect the UTP cable in the package from the
“Ethernet” port of the POE-162S to the RJ45 port of
a remote device.
5. Adjust the proper DC power output and connect the
DC plug from the “DC OUT” of the POE-162S to a
remote device.
6. Power on the remote device and its power LED indi-
cator will remain on.
Switch
Power 12V/24V
POE-162S
100 meters
Power
Data
Power
Data
PoE
Power
Data
AC
DC
Non-PoE PTZ
IP Camera
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line (AC)
AC
DC
Power Line (DC)
802.3at PoE Injector
802.3at PoE
Splitter
Figure 4: Connection architecture over 802.3at PoE+
Injector/POE-162S
Note
1. Owing to IEEE 802.3at/802.3af Power
over Ethernet standards, the 802.3at
PoE+ Injector will not inject power
over the cable if not connected to IEEE
802.3at/802.3af devices.
2. Please ensure the POE-162S output
voltage is correct before applying power
to remote devices.
The 802.3at PoE+ Injector and POE-E201 IEEE
802.3at PoE+ Extender Installation
1. Connect the AC power cord to the “AC slot” of the
802.3at PoE+ Injector; the “POWER” LED will be
steadily on.
2. Connect a standard network cable from the “POE”
port of the 802.3at PoE+ Injector to the “IN” port of
the POE-E201.
3. The 802.3at PoE+ Injector delivers both Ethernet
Data and PoE power over UTP cable to the POE-E201
and the “ACTIVE” LED of the 802.3at PoE+ Injector
and the “PoE IN” LED of the POE-E201 will continue
to be lit.
4. Connect an additional standard network cable that
will be used to connect from the “OUT” port of the
POE-E201 to a remote Powered Device (PD).
5. The “OUT” port of the power injector transmits DC
voltage over the standard network cable and trans-
fers data and power simultaneously between the
802.3at PoE+ Injector and the PD.
6. Once the POE-E201 detects the existence of an IEEE
802.3at/802.3af device, the “PoE OUT” LED indi-
cator will be steadily on to show it is providing power.
802.3at
PoE Extender
Data
PoE PoE
+
Power
Power
Data +
Power
Data
100 meters100 meters
200 meters
Power Line (AC)
AC
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE IP Camera
802.3at PoE Injector
Figure 5: Connection architecture over 802.3at PoE+
Injector/POE-E201
Note
1. If the connected device is not fully
complying with IEEE 802.3at/802.3af
standards or in-line power device, the
PoE OUT LED indicator of the POE-E201
will not be steadily on.
2. Owing to IEEE 802.3at/802.3af
standards, the POE-E201 will not inject
power over the cable if a standard IEEE
802.3at/802.3af device is not connected.
Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource at the PLANET Web
site rst to check if it could solve you issue. If you
need more support information, please contact PLANET
support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php?type=2
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.