User's Manual
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Overview
Thank you for purchasing PLANET IEEE 802.3at Power over
Ethernet Plus Splitters. These PoE splitters will work with
any Power Sourcing Equipment (PSE) that also supports the
IEEE 802.3at standards. The models below are included:
Model
PoE
Standard
DC Power
Out
Power
Input
Pass-thru. Speed
POE-161S
IEEE
802.3at/af
5V/12V
52~56V
DC
10/100/1000Mbps
POE-162S
IEEE
802.3at/af
12V/24V
52~56V
DC
10/100/1000Mbps
Unless specied, the term “802.3at PoE+ Splitter” in the
following sections means the models listed above.
3. Product Outlook
POE-161S
There are two RJ45 twisted-pair jacks, one LED indicator, one
DC 5V/4.5A, 12V/2A DIP switch and one DC plug connector.
IEEE 802.3at PoE Plus Splitter
PoE In
Note
PoE In
Disconnect "PoE In" cable
before change 5/12V
DC Out Ethernet
5V 12V
Incorrect voltage might
cause device damage
CAUTION
Figure 1: POE-161S Overview
POE-162S
There are two RJ45 twisted-pair jacks, one LED indicator, one
DC 12V/2A, 24V/1A DIP switch and one DC plug connector
Note
IEEE 802.3at High Power PoE Splitter
DC Out Ethernet
PoE In
PoE In
24V 12V
Incorrect voltage might
cause device damage
CAUTION
Disconnect "PoE In" cable
before change 12/24V
Figure 2: POE-162S Overview
5.2 802.3at Device Installation
1. PLANET 802.3at PoE+ Splitter also provides an alternative
to making the non IEEE 802.3af/802.3at devices connect
with an IEEE 802.3at PSE power device like Power over
Ethernet Plus Injector or Power over Ethernet Plus Switch as
the gure is shown below.
100 meters
PTZ Speed
Dome
DC
Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
802.3at In-line Power Switch
PoE
Power
Data
802.3at
PoE+ Splitter
Power
Data
DC
POE-161S (Power 5V/12V)
POE-162S (Power 24V/12V)
5V 12V
Incorrect voltage might
cause device damage
CAUTION
24V 12V
Incorrect voltage might
cause device damage
CAUTION
Figure 3: “802.3at PoE+ Splitter” Connecting to IEEE 802.3at Device
Note
With IEEE 802.3af/802.3at standard, PLANET 802.3at
PoE+ Splitter also can function with IEEE
802.3af/802.3at End-span Switch that feeds power
over Pins 1, 2, and 3, 6.
5. Hardware Installation
This section describes the hardware features of 802.3at PoE+
Splitter. Before connecting any network device to the 802.3at
PoE+ Splitter, refer to this chapter carefully.
5.1 Before Installation
PLANET 802.3at PoE+ Splitter separates the power out and
provides two kinds of DC power output through its DIP switch,
and its voltage and current are shown below:
Model
DIP Switch for DC
Voltage Output
Default
Mode
POE-161S
DC Out Ethernet
5V 12V
Incorrect voltage might
cause device damage
CAUTION
5V DC, 4.5A
12V DC, 2A
5V DC
POE-162S
DC Out Ethernet
24V 12V
Incorrect voltage might
cause device damage
CAUTION
12V DC, 2A
24V DC, 1A
12V DC
2. Package Contents
Open the box of the 802.3at PoE+ Splitter and carefully
unpack it. The box should contain the following items:
POE-161S POE-162S
The IEEE 802.3at Gigabit
Power over Ethernet Plus
Splitter x 1
User's Manual x 1
15cm UTP Straight
Network Cable x1
DC Plug Cable x 2
-DC Plug Cable 5.5/2.5mm
to 5.5/2.5mm x 1
-DC Plug Cable 5.5/2.5mm
to 5.5/2.1mm x 1
The IEEE 802.3at Gigabit
Power over Ethernet Plus
Splitter x 1
User’s Manual x 1
15cm UTP Straight
Network Cable x1
DC Plug Cable x 2
-DC Plug Cable 5.5/2.5mm
to 5.5/2.5mm x 1
-DC Plug Cable 5.5/2.5mm
to 5.5/2.1mm x 1
Note
If any of these pieces are missing or damaged,
please contact your dealer immediately. If possible,
retain the carton including the original packing
material, and use them again to repack the
product in case of a need to return for repair.
4. LED Indication
LED Color Function
PoE In Green
Lights to indicate the port is connected with
IEEE 802.3at PSE device.
Note
2.5mm
The diameter of the hole of the 802.3at
PoE+ Splitter’s DC plug connector
measures 2.5mm. The POE-161S and
POE-162S provide 5V/12V and 12V/24V
DC power output through DIP switch
setting, respectively.
DC Receptacle
2.5mm
Note
PLANET 802.3at PoE+ Splitter and PLANET
802.3at PoE+ Injector (e.g. POE-161, POE-163
and POE-164) can be installed in pair. Use of third-
party 802.3at PoE+ Injector device is allowed if
the device complies with IEEE 802.3at standard.
5.3 802.3at PoE+ Injector and 802.3at PoE+ Splitter
Installation
The 802.3at PoE+ Splitter and 802.3at PoE+ Injector
can run in pair to provide DC Power for those non-PoE remote
devices or Ethernet equipment. The table below shows PLANET
802.3at PoE+ Injector models:
Model
PoE
Standard
Max. PoE
Out
Power
In
Pass-thru. Speed
POE-161
IEEE
802.3at/af
30 watts 56V DC 10/100/1000Mbps
POE-163
IEEE
802.3at/af
30 watts 54V DC 10/100/1000Mbps
POE-164
IEEE
802.3at/af
30 watts 53V DC 10/100Mbps
Installation Steps:
1. [Switch & 802.3at PoE+ Injector] Connect a stan-
dard network UTP cable from a switch/workstation to the
“Ethernet” port of the 802.3at PoE+ Injector, which gets
DC power from the attached power adapter.
2. [802.3at PoE+ Injector & 802.3at PoE+ Splitter]
Connect a long UTP cable between the “Ethernet+DC”
(or “PoE”) port of the 802.3at PoE+ Injector and the
“PoE IN” port of the 802.3at PoE+ Splitter.
The PoE LEDs of both the 802.3at PoE+ Injector and
802.3at PoE+ Splitter will light up continuously.