User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP Table
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.7.1 System Time Correction Manually
- 4.2.1.8 Time Configuration
- 4.2.1.9 UPnP
- 4.2.1.10 DHCP Relay
- 4.2.1.11 DHCP Relay Statistics
- 4.2.1.12 CPU Load
- 4.2.1.13 System Log
- 4.2.1.14 Detailed Log
- 4.2.1.15 Remote Syslog
- 4.2.1.16 SMTP Configuration
- 4.2.1.17 Fault Alarm
- 4.2.1.18 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.2.13 VLAN Translation
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.4.2 Bandwidth Control
- 4.4.4.2 DSCP-based QoS
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 5. COMMAND LINE MODE
- 6. SWITCH OPERATION
- 7. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of MGSD-10080F
392
4.7.2.6 Tracerouter(IPv6)
This page allows you to perform a traceroute test over IPv6 towards a remote host. traceroute is a diagnostic tool for
displaying the route and measuring transit delays of packets across an IPv6 network.
You can configure the following parameters for the test: The traceroute (IPv6) screen in Figure 4-7-2-6 appears.
Figure 4-7-2-6: Traceroute (IPv6) Page Screenshot
The page includes the following fields:
Object Description
• Hostname or IP Address
The destination IP Address.
• DSCP Value
This value is used for the DSCP value in the IPv4 header. The default value is
0. The valid range is 0-255.
• Number of Probes Per
Hop (packets)
Determines the number of probes (packets) sent for each hop. The default
value is 3. The valid range is 1-60.
• Response Timeout
(seconds)
Determines the number of seconds to wait for a reply to a sent request. The
default number is 3. The valid range is 1-86400.
• Max TTL Value
Determines the maximum value of the Time-To-Live (TTL) field in the IPv4
header. If this value is reached before the specified remote host is reached
the test stops. The default number is 255. The valid range is 1-255.
• VID for Source Interface
This field can be used to force the test to use a specific local VLAN interface
as the source interface. Leave this field empty for automatic selection based
on routing configuration.
Note: You may only specify either the VID or the IP Address for the
source interface.
• IP Address for Source
Interface
This field can be used to force the test to use a specific local interface with the
specified IP address as the source interface. The specified IP address must
be configured on a local interface. Leave this field empty for automatic