User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP Table
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.7.1 System Time Correction Manually
- 4.2.1.8 Time Configuration
- 4.2.1.9 UPnP
- 4.2.1.10 DHCP Relay
- 4.2.1.11 DHCP Relay Statistics
- 4.2.1.12 CPU Load
- 4.2.1.13 System Log
- 4.2.1.14 Detailed Log
- 4.2.1.15 Remote Syslog
- 4.2.1.16 SMTP Configuration
- 4.2.1.17 Fault Alarm
- 4.2.1.18 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.2.13 VLAN Translation
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.4.2 Bandwidth Control
- 4.4.4.2 DSCP-based QoS
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 5. COMMAND LINE MODE
- 6. SWITCH OPERATION
- 7. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of MGSD-10080F
27
Per 100/1000/2500 SFP Interface (Port 7 to port 8)
LED Color Function
1G/2.5G
LNK/ACT
Green
Lights:
To indicate the link through that port is successfully established at the speed of
1000Mbps or 2500Mbps.
Blink: To indicate that the switch is actively sending or receiving data over that port.
Off: If 1G/2.5G LNK/ACT LED is lit, it indicates the port is operating at
1000Mbps or
2500Mbps.
If 1G/2.5G LNK/ACT LED is off, it indicates that the port is link down or
operating at 100Mbps.
100
LNK/ACT
Orange
Lights:
To indicate the link through that port is successfully established
at the speed of
100Mbps.
Blink: To indicate that the switch is actively sending or receiving data over that port.
Off: If 100 LNK/ACT LED is lit, it indicates that the port is operating at 100Mbps
If 100 LNK/ACT LED is off, it indicates the port is link down or operating at
1000Mbps or 2500Mbps.
Per 10/100/1000BASE-T Interface (Port 9 to port 10)
LED Color Function
1000
LNK/ACT
Green
Lights:
To indicate the link through that port is successfully established
at the speed of
1000Mbps.
Blink:
To indicate that the switch is actively sending or receiving data over that port.
Off: If 1000 LNK/ACT LED is lit, it indicates the port is operating at 1000Mbps.
If 1000 LNK/ACT LED is off, it indicates that the port is link down or
operating at
10/100Mbps .
10/100
LNK/ACT
Orange
Lights:
To indicate the link through that port is successfully established
at the speed of
10Mbps or 100Mbps.
Blink:
To indicate that the switch is actively sending or receiving data over that port.
Off: If 10/100 LNK/ACT LED is lit, it indicates the port is operating at 10/100Mbps.
If 10/100 LNK/ACT LED is off, it indicates the port is link down or operating at
1000Mbps.