User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
439
• RxAps, ReSignal
Received requested signal according to G.8031 figure 11-2
• RxAps, BrSignal
Received bridged signal according to G.8031 figure 11-2
• Dfop
Dfop is "Failure of Protocol defect" and the presence of a defect is indicated
by : no defect, : defect.
CM: Configuration Mismatch (received APS PDU on working interface within last
17.5 seconds).
PM: Provisioning Mismatch (far and near ends are not using the same mode;
bidir only)
NR: No Response (far end hasn't agreed on 'Requested Signal' within 50 ms;
bidir only)
TO: Time Out (near end hasn't received a valid APS PDU within last 17.5
seconds; bidir only)
• SMAC
Source MAC address of last received APS PDU or all-zeros if no PDU has been
received.
• TxCnt
Number of APS PDU frames transmitted.
• RxCnt, Valid
Number of valid APS PDU frames received on the protect port.
• RxCnt, Invalid
Number of invalid APS PDU frames received on the protect port.
Buttons
: Click to refresh the page immediately.