User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
438
which are reflected in the warnings below.
The Warning information is indicated by : no warning, : warning.
Use the tooltip to get the detailed warning information.
• State, Protection
The possible protection group states. The letters refers to the state as described
in G.8031 Annex
No request Working: A.
No request Protecting: B.
Lockout: C.
Forced Switch: D.
Signal fail Working: E.
Signal fail Protecting: F.
Manual switch to Protecting: G.
Manual switch to Working: H.
Wait to restore: I.
Do not revert: J.
Exercise Working: K.
Exercise Protecting: L.
Reverse request Working: M.
Reverse request Protecting: N.
Signal degrade Working: P.
Signal degrade Protecting: Q.
• Defect state, Working,
Protection
The possible values of this field are shown below:
ok: The port defect state is OK
sd: The port defect state is Signal Degrade
sf: The port defect state is Signal Fail
• TxAps, RxAps -
Request
The possible transmitted or received APS request according to G.8031, Table
11-1.
nr: No Request.
dnr: Do Not Revert.
rr: Reverse Request.
exer: Exercise.
wtr: Wait-To-Restore.
ms: Manual Switch.
sd: Signal Degrade.
sfW: Signal Fail for Working.
fs: Forced Switch.
sfP: Signal Fail for Protect.
lo: Lockout.
• TxAps, ReSignal
Transmitted requested signal according to G.8031 figure 11-2
• TxAps, BrSignal
Transmitted bridged signal according to G.8031 figure 11-2