User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
434
4.8.3 ERPS Status
This shows the current status of the ERPS instances. screen in Figure 4-8-3 appears.
Figure 4-8-3: This shows ERPS current status
The page includes the following fields:
Buttons
Auto-refres
h :
Check this
box to
refresh the
page
automatica
lly.
:
Click to
refresh the
page
immediatel
y.
4.8.4
APS
4.8.4.1 APS Configuration
The APS module implements the protocol and linear protection switching mechanisms for point-to-point
Object Description
• ERPS #
The ID of the ERPS. Click on link to get to ERPS detailed instance page, you can
reset counters and issue commands.
• Oper
The operational state of ERPS instance.
: Active
: Disabled or Internal error.
• Warning
Operational warnings of ERPS instance.
: No warnings
: There are warnings, use tooltip to see.
• State
Specifies protection/node state of ERPS.
• TxRapsActive
Specifies whether we are currently supposed to be transmitting R-APS PDUs on
our ring ports.
• cFOPTo
Failure of Protocol - R-APS Rx Time Out.
• UpdateTimeSecs
Time in seconds since boot that this structure was last updated.
• Request
Request/state according to G.8032, table 10-3.
• Version
Version of received/used R-APS Protocol. 0 means v1, 1 means v2, etc.
• Rb
RB (RPL blocked) bit of R-APS info. See Figure 10-3 of G.8032.
• Dnf
DNF (Do Not Flush) bit of R-APS info. See Figure 10-3 of G.8032."
• Bpr
BPR (Blocked Port Reference) of R-APS info. See Figure 10-3 of G.8032.
• Node Id
Node ID of this request.
• SMAC
The Source MAC address used in the request/state.