User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
427
4.8 Ring
4.8.1 Ring Wizard
This page is on ring wizard and it is an interface for user to configure ERPS ring feature.
This wizard uses the fixed ring topology to indicate the ring owner, so if user needs to indicate the other switch to
the ring owner or modify the ring topology, please modify MEP and ERPS settings manually.
If user wants to enable the ERPS ring, please disable the DHCP client feature and indicate the ring port that cannot
be the Spanning Tree port.
Figure: Ring Wizard page screenshot
The page includes the following fields:
Object Description
• All Switch Numbers (3
~ 30)
This option is for you to input a number to show how many switches will be used
for the single ring. Ring wizard needs at least 3 switches for configuring and the
maximum number is 30.
• Number ID
This option is for you to input a number that the ID of the switch you are setting for
the single ring.
For example, a single ring is grouped by 10 switches. If you want to set the ERPS
ring wizard from the 2nd switch, you will have to input 2 for the Number ID option.
• Next Button
When you press the "Next" button, the system is going to generate the ERPS ring
setting according to your setting.
• Ring Wizard Setting
[10 Switches For Single Ring]