User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
41
MGB-TLB40 1000 WDM(LC) Single Mode 40km 1550nm 1310nm
-40 ~ 75 ℃
MGB-TLA80
MGB-TLB80
YES
1000 WDM(LC) Single Mode 80km 1490nm 1550nm
-40 ~ 75 ℃
1000 WDM(LC) Single Mode 80km 1550nm 1490nm
-40 ~ 75 ℃
10Gbps SFP+ (10G Ethernet/10GBASE)
Model DDM Speed (Mbps)
Connector
Interface
Fiber Mode Distance Wavelength (nm) Operating Temp.
MTB-RJ - 10G Copper - 30m -
0 ~ 70 ℃
MTB-SR YES 10G LC Multi Mode Up to 300m 850nm
0 ~ 60 ℃
MTB-LR YES 10G LC Single Mode 10km 1310nm
0 ~ 60 ℃
MTB-TSR YES 10G LC Multi Mode Up to 300m 850nm
-40 ~ 75 ℃
MTB-TLR YES 10G LC Single Mode 10km 1310nm
-40 ~ 75 ℃
10Gbps SFP+ (10GBASE-BX, Single Fiber Bi-directional SFP)
Model DDM Speed (Mbps)
Connector
Interface
Fiber Mode Distance
Wavelength (TX) Wavelength (RX) Operating Temp.
MTB-LA20
MTB-LB20
YES
10G WDM(LC) Single Mode 20km 1270nm 1330nm
0 ~ 60 ℃
10G WDM(LC) Single Mode 20km 1330nm 1270nm
0 ~ 60 ℃
MTB-LA40
MTB-LB40
YES
10G WDM(LC) Single Mode 40km 1270nm 1330nm
0 ~ 60 ℃
10G WDM(LC) Single Mode 40km 1330nm 1270nm
0 ~ 60 ℃
MTB-LA60
MTB-LB60
YES
10G WDM(LC) Single Mode 60km 1270nm 1330nm
0 ~ 60 ℃
10G WDM(LC) Single Mode 60km 1330nm 1270nm
0 ~ 60 ℃
It is recommended to use PLANET SFP/SFP+ on the Managed Switch. If you insert an SFP/SFP+
transceiver that is not supported, the Managed Switch will not recognize it.
1. Before we connect the GS-6320 and MGS-6320 to the other network device, we have to make sure both sides of the SFP
transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to
1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male
duplex LC connector type.
To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male
duplex LC connector type.
Connecting the Fiber Cable
1. Insert the duplex LC connector into the SFP/SFP+ transceiver.
2. Connect the other end of the cable to a device with SFP/SFP+ transceiver installed.
3. Check the LNK/ACT LED of the SFP/SFP+ slot on the front of the Managed Switch. Ensure that the SFP/SFP+
transceiver is operating correctly.
4. Check the Link mode of the SFP/SFP+ port if the link fails. To function with some fiber-NICs or Media Converters, user