User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
391
■ 1: TCP frames where the SYN field is set must be able to match this entry.
■ Any: Any value is allowed ("don't-care").
• TCP RST
Specify the TCP "Reset the connection" (RST) value for this ACE.
■ 0: TCP frames where the RST field is set must not be able to match this
entry.
■ 1: TCP frames where the RST field is set must be able to match this entry.
■ Any: Any value is allowed ("don't-care").
• TCP PSH
Specify the TCP "Push Function" (PSH) value for this ACE.
■ 0: TCP frames where the PSH field is set must not be able to match this
entry.
■ 1: TCP frames where the PSH field is set must be able to match this entry.
■ Any: Any value is allowed ("don't-care").
• TCP ACK
Specify the TCP "Acknowledgment field significant" (ACK) value for this ACE.
■ 0: TCP frames where the ACK field is set must not be able to match this
entry.
■ 1: TCP frames where the ACK field is set must be able to match this entry.
■ Any: Any value is allowed ("don't-care").
• TCP URG
Specify the TCP "Urgent Pointer field significant" (URG) value for this ACE.
■ 0: TCP frames where the URG field is set must not be able to match this
entry.
■ 1: TCP frames where the URG field is set must be able to match this entry.
■ Any: Any value is allowed ("don't-care").
Ethernet Type Parameters
The Ethernet Type parameters can be configured when Frame Type "Ethernet Type" is selected.
Object Description
• EtherType Filter
Specify the Ethernet type filter for this ACE.
■ Any: No EtherType filter is specified (EtherType filter status is
"don't-care").
■ Specific
: If you want to filter a specific EtherType filter with this ACE,
you can enter a specific EtherType value. A field for entering a
EtherType value appears.
• Ethernet Type Value
When "Specific" is selected for the EtherType filter, you can enter a specific
EtherType value.
The allowed range is 0x600 to 0xFFFF but excluding 0x800(IPv4), 0x806(ARP)
and 0x86DD(IPv6). A frame that hits this ACE matches this EtherType value.