User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
280
4.4.8 OSPFv3
4.4.8.1 Global Configuration
This is OSPF6 router configuration table. It is a general group to configure the OSPF6 common router parameters.
The displayed settings are:
Object Description
• OSPF6 Router Mode
Enable/Disable the OSPF6 router mode.
• Default Router ID
The OSPF6 Router ID in IPv4 address format(A.B.C.D).
When the router's OSPF6 Router ID is changed, if there is one or more fully
adjacent neighbors in current OSPF6 area, the new router ID will take effect after
restart OSPF6 process. Notice that the router ID should be unique in the
Autonomous System and value '0.0.0.0' is invalid since it is reserved for the
default algorithm.
Auto: The default algorithm will choose the largest IP address assigned to the
router.
Specific: User specified router ID.
The allowed range is from 0.0.0.1 to 255.255.255.254.
• Static Redistribute
The OSPF redistributeenabled for the static routes or not.
Enable: The static routes are redistributed.
Disable: The static routes are not redistributed
• Connected
Redistribute
The OSPF redistribute enabled for connected route or not.
Enable: The connected interfaces are redistributed.
Disbale: The connected interfaces are not redistributed.
• Administrative istance
The OSPF6 administrative distance.
Buttons
: Click to reset the current OSPF6 process.
: Click to apply changes
: Click to undo any changes made locally and revert to previously saved values.