User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.8 Time Configuration
- 4.2.1.9 Time Configuration
- 4.2.1.10 UPnP
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 SNMP
- 4.2.3 RMON
- 4.2.4 DHCP Relay
- 4.2.5 DHCP server
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLANs
- 4.3.4 VLAN Translation
- 4.3.5 VLAN Translation Mappings
- 4.3.6 Private VLANs
- 4.3.7 VCL
- 4.3.8 GVRP
- 4.3.9 MRP
- 4.3.10 Spanning Tree
- 4.3.11 IGMP Snooping
- 4.3.12 MLD Snooping
- 4.3.13 MVR (Multicast VLAN Registration)
- 4.3.14 LLDP
- 4.3.15 MAC Address Table
- 4.3.16 Loop Protection
- 4.3.17 UDLD
- 4.3.18 Link OAM
- 4.3.19 CFM
- 4.3.20 sFlow
- 4.4 Routing
- 4.5 QoS
- 4.6 Security
- 4.7 POE
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-6320 and MGS-6320 Managed Switches
256
Router ID The OSPF Router ID in IPv4 address format(A.B.C.D).
When the router's OSPF Router ID is changed, if there is one or more fully adjacent neighbors in
current OSPF area, the new router ID will take effect after restart OSPF process. Notice that the
router ID should be unique in the Autonomous System and value '0.0.0.0' is invalid since it is
reserved for the default algorithm.
Auto: The default algorithm will choose the largest IP address assigned to the router.
Specific: User specified router ID.
Default Passive Mode Configure all interfaces as passive-interface by default.When an interface is configured as a
passive-interface, the OSFP routing updates sending is suppressed, therefore the interface does
not establish adjacencies (No OSPF Hellos). The subnet of all interfaces (both passive and active)
is advertised by the OSPF router.
Default Metric User specified default metric value for the OSPF routing protocol. The field is significant only when
the arugment 'IsSpecificDefMetric' is TRUE
Auto: The default metric is calculated automatically based on the routing protocols.
Specific: User specified default metric.
Static Redistribute
Metric Type
The OSPF redistributed metric type for the connected interfaces.
None: The static routes are not redistributed.
Specified Metric Value: User specified metric for the static routes.
External Type 1: External Type 1 of the static routes.
External Type 2: External Type 2 of the static routes.
Static Redistribute
Metric Value
User specified metric value for the connected interfaces. The field is significant only when the
arugment 'ConnectedRedistMetricType' is configured as 'metricTypeSpecified'.
The allowed range is 0 to 1677214.
Connected
Redistribute Metric
Type
The OSPF redistributed metric type for the static routes.
None: The connected interfaces are not redistributed.
Specified Metric Value: User specified metric for the connected interfaces routes.
External Type 1: External Type 1 of the connected interfaces routes.
External Type 2: External Type 2 of the connected interfaces routes.
Connected
Redistribute Metric
Value
User specified metric value for the static routes.The field is significant only when the arugment
'StaticRedistMetricType' is configured as 'metricTypeSpecified'.
The allowed range is 0 to 1677214.
Buttons
Click to reset the current OSPF process.
Click to save changes.
: Click to undo any changes made locally and revert to previously saved values.