User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.3 Port Management
- 4.4 Link Aggregation
- 4.5 VLAN
- 4.5.1 VLAN Overview
- 4.5.2 IEEE 802.1Q VLAN
- 4.5.3 Management VLAN
- 4.5.4 Create VLAN
- 4.5.5 Interface Settings
- 4.5.6 Port to VLAN
- 4.5.7 Port VLAN Membership
- 4.5.8 Protocol VLAN Group Setting
- 4.5.9 Protocol VLAN Port Setting
- 4.5.10 GVRP Setting
- 4.5.11 GVRP Port Setting
- 4.5.12 GVRP VLAN
- 4.5.13 GVRP Statistics
- 4.5.14 VLAN setting example:
- 4.6 Spanning Tree Protocol
- 4.7 Multicast
- 4.8 Quality of Service
- 4.9 Security
- 4.10 ACL
- 4.11 MAC Address Table
- 4.12 LLDP
- 4.13 Diagnostics
- 4.14 RMON
- 4.15 Power over Ethernet
- 4.16 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A
- EC Declaration of Conformity
User’s Manual of LRP-822CS/LRP-1622CS
Gigabit SFP Transceiver Modules
MGB-GT
SFP-Port 1000BASE-T Module
MGB-SX
SFP-Port 1000BASE-SX mini-GBIC module
MGB-LX
SFP-Port 1000BASE-LX mini-GBIC module
MGB-L50
SFP-Port 1000BASE-LX mini-GBIC module – 50km
MGB-L70
SFP-Port 1000BASE-LX mini-GBIC module – 70km
MGB-L120
SFP-Port 1000BASE-LX mini-GBIC module – 120km
MGB-LA10
SFP-Port 1000BASE-LX (WDM,TX:1310nm) – 10km
MGB-LA20
SFP-Port 1000BASE-LX (WDM,TX:1310nm) – 20km
MGB-LB20
SFP-Port 1000BASE-LX (WDM,TX:1550nm) – 20km
MGB-LA40
SFP-Port 1000BASE-LX (WDM,TX:1310nm) – 40km
MGB-LB40
SFP-Port 1000BASE-LX (WDM,TX:1550nm) – 40km
Fast Ethernet SFP Transceiver Modules
MFB-FX
SFP-Port 100BASE-FX Transceiver – 2km
MFB-F20
SFP-Port 100BASE-FX Transceiver – 20km
MFB-F60
SFP-Port 100BASE-FX Transceiver – 60km
MFB-FA20
SFP-Port 100BASE-BX Transceiver (WDM,TX:1310nm) – 20km
MFB-FB20
SFP-Port 100BASE-BX Transceiver (WDM,TX:1550nm) – 20km
It is recommended to use PLANET SFP on the LRP Managed Switch. If you insert an SFP
transceiver that is not supported, the LRP Managed Switch will not recognize it.
In the installation steps below, this Manual uses Gigabit SFP transceiver as an example. However,
the steps for Fast Ethernet SFP transceiver are similar.
1. Before we connect LRP Managed Switch to the other network device, we have to make sure both sides of the SFP
transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to
1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male
duplex LC connector type.
To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male
duplex LC connector type.
31