User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.3 Port Management
- 4.4 Link Aggregation
- 4.5 VLAN
- 4.5.1 VLAN Overview
- 4.5.2 IEEE 802.1Q VLAN
- 4.5.3 Management VLAN
- 4.5.4 Create VLAN
- 4.5.5 Interface Settings
- 4.5.6 Port to VLAN
- 4.5.7 Port VLAN Membership
- 4.5.8 Protocol VLAN Group Setting
- 4.5.9 Protocol VLAN Port Setting
- 4.5.10 GVRP Setting
- 4.5.11 GVRP Port Setting
- 4.5.12 GVRP VLAN
- 4.5.13 GVRP Statistics
- 4.5.14 VLAN setting example:
- 4.6 Spanning Tree Protocol
- 4.7 Multicast
- 4.8 Quality of Service
- 4.9 Security
- 4.10 ACL
- 4.11 MAC Address Table
- 4.12 LLDP
- 4.13 Diagnostics
- 4.14 RMON
- 4.15 Power over Ethernet
- 4.16 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A
- EC Declaration of Conformity
User’s Manual of LRP-822CS/LRP-1622CS
291
match this entry.
Don’t Care: Any value is allowed ("don't-care").
SYN Specify the TCP "Synchronize sequence numbers" (SYN) value for this
ACE.
Set: TCP frames where the SYN field is set must be able to match
this entry.
Unset: TCP frames where the SYN field is set must not be abl
match
e to
this entry.
Don’t Care: Any value is allowed ("don't-care").
FIN Specify the TCP "No more data from sender" (FIN) value for this ACE.
Set: TCP frames where the FIN field is set must be able to match
this entry.
Unset: TCP frames where the FIN field is set must not be able to
match this entry.
Don’t Care: Any value is allowed ("don't-care").
Type of Service
y thSpecif e type of service for this ACE.
Any: ific type of service is specified (destination port status is No spec
"don't-care").
filter a specific DSCP with this ACE, you can enter a DSCP: If you want to
specific DSCP value. A field for entering a DSCP value appears. The allowed
range is 0 to 63. A frame that hits this ACE matches this DSCP value.
IP Recedence: If you want to filter a specific IP recedence with this ACE, you
n eca nter a specific IP recedence value. A field for entering a IP recedence
value . The allowed range is 0 to 7. A frame that hits this ACE appears
matches this IP recedence value.
ICMP
Specif y the ICMP for this ACE.
Any: No specific ICMP is specified (destination port status is "don't-care").
ecific list with this ACE, you can select a specific List: If you want to filter a sp
list value.
Prot ACE, you ocol ID: If you want to filter a specific protocol ID filter with this
can enter a specific protocol ID value. A field for entering a protocol ID value
appears. The allowed range is 0 to 255. A frame that hits this ACE matches
this protocol ID value.
ICMP Code
Specif is ACE. y the ICMP code filter for th
Any: No ICMP code filter is specified (ICMP code filter status is "don't-care").
User , Defined: If you want to filter a specific ICMP code filter with this ACE
you can enter a specific ICMP code value. A field for entering an ICMP code
value appears. The allowed range is 0 to 255. A frame that hits this ACE
matches this ICMP code value.