User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.3 Port Management
- 4.4 Link Aggregation
- 4.5 VLAN
- 4.5.1 VLAN Overview
- 4.5.2 IEEE 802.1Q VLAN
- 4.5.3 Management VLAN
- 4.5.4 Create VLAN
- 4.5.5 Interface Settings
- 4.5.6 Port to VLAN
- 4.5.7 Port VLAN Membership
- 4.5.8 Protocol VLAN Group Setting
- 4.5.9 Protocol VLAN Port Setting
- 4.5.10 GVRP Setting
- 4.5.11 GVRP Port Setting
- 4.5.12 GVRP VLAN
- 4.5.13 GVRP Statistics
- 4.5.14 VLAN setting example:
- 4.6 Spanning Tree Protocol
- 4.7 Multicast
- 4.8 Quality of Service
- 4.9 Security
- 4.10 ACL
- 4.11 MAC Address Table
- 4.12 LLDP
- 4.13 Diagnostics
- 4.14 RMON
- 4.15 Power over Ethernet
- 4.16 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A
User’s Manual of LRP-422CST
Range: If you want to filter a specific source port range filter with this ACE, you
can enter a specific source port range value. A field for entering a source port
value appears. The allowed range is 0 to 65535. A frame that hits this ACE
matches this source port value.
Destination Port
Specify the destination port for this ACE.
Any: No specific destination port is specified (destination port status is
"don't-care").
Single: If you want to filter a specific destination port with this ACE, you can enter
a specific destination port value. A field for entering a destination port value
appears. The allowed range is 0 to 65535. A frame that hits this ACE matches this
destination port value.
Range: If you want to filter a specific destination port range filter with this ACE,
you can enter a specific destination port range value. A field for entering a
destination port value appears.
UGR Specify the TCP "Urgent Pointer field significant" (URG) value for this ACE.
Set: TCP frames where the URG field is set must be able to match this
entry.
Unset: TCP frames where the URG field is set must not be able to
match this entry.
Don’t Care: Any value is allowed ("don't-care").
ACK Specify the TCP "Acknowledgment field significant" (ACK) value for this
ACE.
Set: TCP frames where the ACK field is set must be able to match this
entry.
Unset: TCP frames where the ACK field is set must not be able to match
this entry.
Don’t Care: Any value is allowed ("don't-care").
PSH Specify the TCP "Push Function" (PSH) value for this ACE.
Set: TCP frames where the PSH field is set must be able to match this
entry.
Unset: TCP frames where the PSH field is set must not be able to match
this entry.
Don’t Care: Any value is allowed ("don't-care").
RST
Specify the TCP "Reset the connection" (RST) value for this ACE.
Set: TCP frames where the RST field is set must be able to match this
entry.
Unset: TCP frames where the RST field is set must not be able to match
this entry.
Don’t Care: Any value is allowed ("don't-care").
TCP Flags
SYN Specify the TCP "Synchronize sequence numbers" (SYN) value for this ACE.
300