Datasheet

LRP-104CET
5
Specications
Model
LRP-104CET
HardwareSpecications
Ethernet Interface
Copper Ports Four 10/100BASE-TX RJ45 auto-MDI/MDI-X
PoE Injector Ports Four ports with 802.3at/af PoE injector function with Port-1 to Port-4
Functionality Four DIP switches to control PoE output on or off with Port-1 to Port-4
PoE Standards Compliance IEEE 802.3at Power over Ethernet Plus/PSE
PoE Type End-span
PoE Power output
52V DC, PoE output depends on LRP Injector or LRP Switch
52V DC, 25 watts per port (external DC input)
Cabling
Ethernet: 10BASE-T: 2-pair UTP Cat.3, 4 and 5
Ethernet: 100BASE-TX: 2-pair UTP Cat.5, 5e and 6
Maximum Distance 100m
Maximum Frame size 1522 bytes
SRAM Packet Buffer
Connectivity
One BNC female
Long Reach PoE over Coaxial PD
One RJ45 connector
Long Reach PoE over UTP PD
Jumbo Packet Size
Long Reach PoE Interface
Power Input 44~ 56V DC
Power Pin Assignment
BNC center pole: DC+
BNC shield: DC-
RJ45 Pins 1, 3, 5, 7: VCC+
RJ45 Pins 2, 4, 6, 8: VCC-
Cabling
Coaxial cable: 75 ohm
RG-6/Ucable,lessthan12Ω/1000ft.
RG-59/Ucable,lessthan30Ω/1000ft.
Cat. 3, 4, 5, 5e UTP cable (100 meters, max.)
EIA/TIA-568 100-ohm STP (100 meters, max.)
Maximum Distance
Max. 200m with PoE+ output (656ft.)
Max. 400m with PoE output (1,312ft.)
Max. 1000m without PoE output (3,280ft.)
Max. 100m with PoE+ output (328ft.)
Max. 400m with PoE output (1,312ft.)
Long Reach Ethernet Stan dard IEEE 1901
Modulation Type Wavelet-OFDM
Security 128-bit AES encryption
Frequency Band 2 ~ 28 MHz
Encryption AES 128-bit
LRP Compatibility
With power over coaxial input:
■LRP-101CH–1-PortLRPInjector
■LRP-822CS–8-PortLRPoverCoaxSwitch
■•LRP-1622CS–16-PortLRPoverCoax
Switch
With power over UTP input:
■LRP-101UH–1-PortLRPInjector
LED Indicator
3 x LED for External Power
Supply:
Green: DC Power 1
Green: DC Power 2
Red: Power Fault
4 x LED for PoE Usage: Green: 10W/20W/30W/40W
2 x LED for Long Reach PoE In:
Green: PWR
Green: LNK
2 x LED for each RJ45 interface
(Port-1 and Port-4)
Green: 10/100Mbps LNK/ACT
Orange: PoE-in-use
Installation DIN rail kit and wall-mount kit
Dimensions (W x D x H) 135 x 87.8 x 56 mm
Weight 644g
Power Requirements
44~56V DC power over coaxial input
DC 24~48V, redundant power with polarity reverses protection function
Power Consumption/
Dissipation
130 watts/446BTU (Ethernet with PoE Full Loading)
Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
Enclosure Aluminum case
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet/10BASE-T
IEEE 802.3u Fast Ethernet/100BASE-TX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3at Power over Ethernet Plus
Regulatory Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (anti-shock)
IEC60068-2-6 (anti-vibration)