-Port 10/100TX over Coaxial Long Reach Ethernet Extender LRE-101C User’s Manual
Trademarks Copyright © PLANET Technology Corp. 2022. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
ISEDC Statement CAN ICES-003(A) / NMB-003(A) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Table of Contents 1. Package Contents.................................................................................. 5 2. Hardware Introduction........................................................................... 6 2.1 Physical Dimensions........................................................................ 6 2.2 Front View..................................................................................... 7 2.3 Rear View..........................................................................
1. Package Contents Thank you for purchasing PLANET LRE-101C 1-Port 10/100TX over Coaxial Long Reach Ethernet Extender. In the following sections, the term “EoC Converter” means the LRE-101C. Open the box of the EoC Converter and carefully unpack it.
2. Hardware Introduction 2.1 Physical Dimensions Dimensions (W x D x H): 94 x 70.3 x 26.2mm 26.20 Slave Master Long Reach 70.30 LNK LNK/ ACT LAN 10/100TX 5V DC Master PWR Long Reach Ethernet over Coaxial Extender LRE-101C Long Reach Ethernet 10/100TX over Coaxial Extender 94.00 46.70 ∅ 7.
2.2 Front View LRE-101C Front Panel Long Reach LAN LNK LRE-101C LNK/ ACT Master PWR 10/100TX Long Reach Ethernet over Coaxial Extender 10/100TX RJ45 connector BNC female connector for Long Reach LEDs for power, Ethernet and Long Reach LRE-101C LED Indicators The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system. System LED PWR Function Color Green Lit: Indicates that the EoC Converter has power.
DIP Switch Setting In the PtMP setting, it can be one master and more than one slave with BNC T connector. LED Master Function Color Green Lit: Indicates that the LRE-101C is functioned as a Master. Off: Indicates that the LRE-101C is functioned as a Slave. 2.3 Rear View LRE-101C Rear Panel 5V DC Master Slave DIP switch: Master/Slave mode selectable DC jack (DC input) for power adapter DIP Switch The EoC Converter provides a selectable 2-position DIP switch.
2.4 Power Information The LRE-101C requires 5V DC, 2A power input, which conforms to the bundled AC adapter. Should you have the issue of power connection, contact your local sales representative. 2.5mm DC Receptacle 2.5mm +5V for each slot DC receptacle is 2.5mm wide that conforms to the EoC Converter 2.5mm DC jack’s central post. Do not install any improper unit.
3. Product Specifications Product LRE-101C Hardware Specifications 1 10/100BASE-TX RJ45 Copper port, auto-negotiation/auto-MDI/MDI-X LAN Ethernet interface Cabling Cat5e UTP or above Maximum Distance 100 meters Maximum Frame Size 1522 bytes 1 BNC female Ethernet over Coaxial Long Reach Interface Cabling Coaxial cable: 75 ohm RG-6/U cable, less than 12Ω/1000 ft RG-59/U cable, less than 30Ω/1000 ft Maximum Distance Max. 2000 with data transmission (6,561ft.
1600m 35/33Mbps Long Reach Interface Performance* 1800m 34/23Mbps 2000m 3/8Mbps Functionality DIP Switch Select Master or Slave mode Dimensions (W x D x H) 97 x 70.3 x 26 mm Weight 194g Housing Metal Power Requirement 5V DC, 2A external power LED Indicators Power: Green LAN: Green, 10/100Mbps LNK/ACT Long Reach: Green, LNK Master: Green Standards Conformance Standards Compliance IEEE 802.3/802.3u Ethernet standard compliant IEEE 802.3x Full-duplex flow control IEEE 802.
4. Installations 4.1 Wall-mount Installation Step 1: Find a suitable wall to mount the LRE-101C. Step 2: Screw two screws on the wall. Step 3: Hang the LRE-101C on the screws from the wall. Step 4: Repeat Chapter 2.4 Power Information on power supply to the LRE-101C. 5V DC 10GBASE-T to 10GBASE -X Before mounting the device to the wall, please check the location of the electrical outlet and the length of the Ethernet cable.
4.2 Chassis Installation and Rack Mounting To install the EoC Converter in a 10-inch or 19-inch Converter Chassis with standard rack, follow the instructions described below. Step 1: Place your LRE-101C on a hard flat surface, with the front panel positioned towards your front side. Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the converter chassis.
4.3 Optional DIN-rail Installation There are two DIN-rail holes on the left side of the LRE-101C that allows to be easily installed by DIN-rail mounting. PLANET optional DIN-rail mounting kit – RKE-DIN -- can be ordered separately. Refer to the following steps for the DIN-rail mounting of the LRE-101C: Step 1: Screw the DIN rail on the LRE-101C. Step 2: Now slide the DIN rail into the track. Step 3: Check whether the DIN rail is tightly on the track.
5. Applications The EoC Converter does not require any software configuration. Users can immediately use any feature of this product simply by attaching the cables and turning the power on. There are some key limitations on the EoC Converter. Please check the following items. 5.1 Point-to-Point Application -- LAN to LAN Connection One set of the EoC Converter could be used to link two local area networks that are located in different places.
5.2 LRE-101C Point to Multi-point Application (IP surveillance) 5V DC adapter Switch LRE-101C Coax. Slave IP Camera NVR 5V DC adapter BNC Tee Connector Coax. Video Coax. LRE-101C Monitor LRE-101C Master 100m 5V DC adapter Slave 1600m IP Camera 100m 100BASE-TX UTP Video Video Line Coax. Coaxial Cable Building an IP surveillance system Refer to the following procedure to set up an IP surveillance system with many pairs of the LRE-101C: 1.
6. Performance Table LRE-101C Upstream/Downstream Performance Coaxial Distance (meter) (Upstream/Downstream) Unit: Mbps 200 94 94 500 94 94 600 94 94 800 88 87 1000 76 73 1200 61 58 1400 45 43 1600 35 33 1800 34 23 2000 3 8 *** The actual data rate will vary in the quality of the coaxial cables and environmental factors.
7. Troubleshooting SYMPTOM: LNK LED does not light up after wire is connected to the Long Reach port. CHECKPOINT: Please note you must use one LRE-101C in Master mode and the other LRE-101C in Slave mode to make connection to each other work SYMPTOM: TP LED does not light after cable is connected to the port. CHECKPOINT: 1. Verify you are using the Cat5e or better cable with RJ45 connector to connect to the port. 2.
8. FAQs Q1: What is the best distance for LRE-101C? A1: In order to guarantee the stability and better quality of network, we suggest the distance should not exceed 700m (Cat.5 UTP) and 1200m (Phone wire).
9. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Switch support team mail address: support@planet.com.tw Copyright © PLANET Technology Corp. 2022. Contents are subject to revision without prior notice.