Industrial 10G/5G/2.
Trademarks Copyright © PLANET Technology Corp. 2018. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol.
Table of Contents 1. Introduction............................................................................... 5 1.1 Package Contents................................................................ 5 1.2 Product Overview................................................................. 6 1.3 Product Features.................................................................. 7 1.4 Product Specifications.......................................................... 8 2. Hardware Description......................
1. Introduction 1.1 Package Contents Thank you for purchasing PLANET Industrial 10G Media Converter, In the following section, unless specified, the term “Industrial Media Converter” mentioned in this manual refers to the IXT-705AT. Open the box of the Industrial Media Converter and carefully unpack it.
1.2 Product Overview Flexible, Reliable and Industrial-grade Network Distance Extension Solution PLANET IXT-705AT Industrial Media Converter is equipped with one 100/1000/2500/5000/10000BASE-T auto-negotiation port and one 10GBASE-X SFP+ slot. It supports 10Gigabit Ethernet media conversion from copper 10GBASE-T to fiber multi-mode or single-mode, utilizing 10GBASE-SR or 10GBASE-LR SFP+ transceiver installed in the SFP+ slot to extend distances to servers, switches and patch panels.
equipped with two DC power input connectors for redundant power supply installation. It also possesses an integrated power supply source with wide-ranging voltages (12 to 48V DC or 24V AC) for worldwide high availability applications requiring dual or backup power inputs, incorporated into customer’s automation network to enhance system reliability and uptime. 1.
1.
Address Table 9K entries, automatic source address learning and aging Jumbo Frame 16K Network Cables 10000/5000/2500/1000/100 BASE-T: Cat5e, 6, 6A, 7 UTP cable (100 meters, max.) EIA/TIA-568 100-ohm STP (100 meters, max.) 10GBASE-LR/SR/BX: 50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 300m 9/125μm single-mode fiber optic cable, up to 60km Standards Conformance Standards Compliance IEEE IEEE IEEE IEEE IEEE IEEE 802.3u 100BASE-TX 802.3ab 1000BASE-T 802.3bz 2.5G/5GBASE-T 802.
2. Hardware Description 2.1 Physical Dimensions Mounting Kit Side View Rear View DIN-Rail Kit Mounting Kit IXT-705AT dimensions (W x D x H): 32 x 87 x 135mm Input DC12~48V, AC 24V 5G/100 Side View IXT-705AT DC2 10GBASE-T 2.
2.2 Converter Front Panel and LED Indicators Figure 2-1 shows the front panels of the Industrial Media Converter. System LED P1 P2 FAULT Color P1 Green P2 Green FAULT Red 10G SFP+ Function Lit: Power 1 is active Off: Power 1 is inactive Lit: Power 2 is active Off: Power 2 is inactive Lit: indicates either power 1 or power 2 has no power. Off: No failure Per 10000/5000/2500/1000/100BASE-T Port 10GBASE-T 2.5G 10G/1G LED Color Green Orange Lit: To indicate that the port is operating at 10/1Gbps.
3. Installation This section describes the functionalities of the Industrial Media Converter’s components and guides you to how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 3.1 Quick Installation Steps Step 1: Unpack the Industrial Media Converter. Step 2: Check whether the DIN-rail is screwed on the Industrial Media Converter.
3.2 Mounting Installation This section describes how to install the Industrial Media Converter and makes connections to it. Please read the following topics and perform the procedures in the order being presented. Note In the installation steps below, this Manual uses IGS-801 (PLANET 8-port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Switch and Industrial Media Converter are similar. 3.2.
Step 3: Make sure the DIN rail is tightly secured on the track. Step 4: Please refer to the following procedures to remove the Industrial Media Converter from the trac 1 2 Step 5: Lightly pull out the bottom of the DIN rail from the track to remove. 3.2.2 Wall-mount Plate Mounting To install the Industrial Media Converter on the wall, please follow the instructions described below. Step 1: Remove the DIN rail from the Industrial Media Converter; loosen the screws to remove the DIN rail.
Step 2: Place the wall-mount plate on the rear panel of the Industrial Media Converter. Step 3: Use the screws to screw the wall-mount plate on the Industrial Media Converter. Step 4: Use the hook holes at the corners of the wall-mount plate to hang the Industrial Media Converter on the wall. Step 5: To remove the wall-mount plate, reverse the steps above. 3.
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 Power 1 + - Note 3 4 Fault 5 6 Power 2 + - The wire gauge for the terminal block should be in the range between 12 and 24 AWG. 3.4 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. When inserting the wires, the Industrial Media Converter will detect the fault status of the power failure and then forms an open circuit.
Note The wire gauge for the terminal block should be in the range between 12 and 24 AWG. 3.5 Cable Connection Installing the SFP+ Transceiver The sections describe how to insert an SFP+ transceiver into an SFP+ slot. The SFP+ transceivers are hot-pluggable and hot-swappable.
1. Make sure both sides of the SFP+ transceiver are with the same media type; for example, 10GBASE-SR to 10GBASE-SR, 10GBASE-LR to 10GBASE-LR. 2. Check whether the fiber-optic cable type matches the SFP+ transceiver model. To connect to 10GBASE-SR SFP+ transceiver, use the multi-mode fiber cable with one side being the male duplex LC connector type. To connect to 10GBASE-LR SFP+ transceiver, use the single-mode fiber cable with one side being the male duplex LC connector type.
Note Never pull out the module without pulling the lever or the push bolts on the module. Directly pulling out the module with effort could damage the module and SFP+ module slot of the Industrial Media Converter. 100/1000/2500/5000/10000BASE-T The 100/1000/2500/5000/10000BASE-T port comes with autonegotiation capability. It automatically supports 100BASE-TX, 1000BASE-T, 2500BASE-T, 5000 BASE-T and 10000 BASE-T networks.
4. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Media Converter is not functioning properly, make sure the Industrial Media Converter is set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Media Converter. Performance is bad Solution: Check the speed duplex mode of the partner device.
APPENDIX A: Approved PLANET SFP+ Transceivers PLANET Industrial Media Converter supports 100/1000 dual mode with both single mode and multi-mode SFP+ transceivers.
APPENDIX B: Networking Connection B.
B.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
EC Declaration of Conformity For the following equipment: *Type of Product : *Model Number : * Produced by: Manufacturer Name Manufacturer Address Industrial 10G/5G/2.5G/1G/100M Copper to 10GBASE-X SFP+ Media Converter IXT-705AT : Planet Technology Corp. : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.
