Quick Guide

ManualsBrandsPLANET Technology ManualsIndustrial EthernetIndustrial 5-Port 10/100/1000T VPN Security Gateway

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

4.2 Logging in to the VPN Gateway

ThenrefertothestepsbelowtoconguretheVPN Gateway:

Step 1: Connect the IT administrator’s PC and VPN Gateway’s LAN

port (port 1) to the same hub/switch, and then launch a

browser to link the management interface address which

is set to https://192.168.1.1 by default.

PC/Workstation with

IP 192.168.1.x

RJ45/UTP Cable

IVR Series

Device IP 192.168.1.1

Figure 4-1: IP Management Diagram

Note

The DHCP server of the VPN Gateway is enabled.

Therefore, the LAN PC will get IP from the VPN Gateway.

If user needs to set IP address of LAN PC manually,

please set the IP address within the range between

192.168.1.2 and 192.168.1.254 inclusively, and assigned

the subnet mask of 255.255.255.0.

Step 2: The browser prompts you for the login credentials. (Both

are “admin” by default.)

Default IP address: 192.168.1.1

Default user name: admin

Default password: admin

Default 2.4GHz SSID: PLANET_2.4G (for IVR-300W)

Default 5GHz SSID: PLANET_5G (for IVR-300W)

Figure 4-2: Web Login Screen

Note

The following web screen is based on the IVR-300W; the

display of the IVR-100 and IVR-300 is the same as that of

the IVR-300W.

Pleasefollowthewizardtodotherst-timeaccountmodication.

The password must contain 8~31 characters, including upper case,

lower case, numerals and other symbols Figure 4-3.

Figure 4-3: Account Modication

After modify new account and password, the main screen appears as

shown in Figure 4-4.

Figure 4-4: Web Main Screen

Now, you can use the Web management interface to continue the

Security Gateway management or manage the Security Gateway by

console interface. Please refer to the user’s manual for more.

Administrators are strongly suggested to change the default password

andWi-FiSSIDonthe rstlogintosafeguardsystemsecurity.

Note

1. For security reason, please change and memorize

the new password after this first setup.

2. Only accept command in lowercase letter under web

interface.

6. Appendix

Appendix A: Default Setting

Default IP Address 192.168.1.1

Default Login User Name admin

Default Login Password admin

Default DHCP Server On

Default LAN Port Ethernet Port 1

Default WAN Port Ethernet Port 5

Appendix B: User’s Manual

User’s Manual

IVR-100 IVR-300 series

5. Recovering Back to Default

 Conguration

5.1 IP Address has been changed or admin password

has been forgotten –

To reset the IP address to the default IP address “192.168.1.1” or

reset the login password to default value, press the hardware reset

button on the front panel for about 10 seconds. After the device is

rebooted, you can log in the management Web interface within the

same subnet of 192.168.1.xx.

Reset

2.4G

Alarm

I/O

IVR-300W

2.4G/5GHz

USB

GND

Reset Button

Figure 5-1: Reset Button of IVR-300 Series

Note

The location of the reset button is the same for all the

IVR-300 series.

7. Customer Support

Thank you for purchasing PLANET VPN Gateway. The above steps

introduce the simple conguration of the VPN Gateway. If you have

other questions, please contact the local dealer where you purchased

this product or you can contact PLANET directly at the following email

address:

PLANET online FAQs:

https://www.planet.com.tw/en/support/faq

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.