Quick Guide

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial Security Gateway, IVR-100
and IVR-300 series. The descriptions of these models are as follows
IVR-100 Industrial 5-Port 10/100/1000T VPN Security Gateway
IVR-300
Industrial 5-Port 10/100/1000T VPN Security Gateway
with Redundant Power
IVR-300W
Industrial 5-Port 10/100/1000T + 802.11ax Wi-Fi VPN
Security Gateway
Open the box of the Security Gateway and carefully unpack it. The box
should contain the following items:
Model
Item
IVR-100 IVR-300 IVR-300W
VPN Gateway x 1 x 1 x 1
Quick Installation Guide x 1 x 1 x 1
Wall-mount Kit x 1 x 1 x 1
Dust Cap x 5 x 5 x 5
CloudViewer QIG x 1 x 1 x 1
RS485 3-pin Terminal Block x 1 x 1
Dual band Wi-Fi Antenna x 2
Antenna Dust Cap x 2
If any of the above items are damaged or missing, please contact your
dealer immediately.
2.2 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of VPN
Gateway is used for two redundant power inputs. Please follow the steps
below to insert the power wire.
Caution
When performing any of the procedures like inserting the
wires or tightening the wire-clamp screws, make sure the
power is OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into contacts 1 and 2 for
POWER 1, or 5 and 6 for POWER 2.
DC Input:
9~48V , 1A max.
Fault
V1+ V2+
PWR2PWR1
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Figure 2-3: Power 1 and Power 2
Note
Please make sure the input voltage is under the
specification of the Security Gateway.
3. Hardware Installation
This section guides you to installing the VPN Gateway on the DIN-rail
and wall. Basic knowledge of networking is assumed. Please read this
chapter completely before continuing.
Note
The installation procedures of the IVR-100 & IVR-300
series are the same as the ones shown below.
3.1 DIN-rail Mounting Installation
3.2 Wall-mount Plate Mounting
2.3 Grounding the Device
User MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device. EMD
(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.
2.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the Security
Gateway will detect the fault status of the power failure or port failure,
and then will form an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts
1 2 3 4 5 6
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Alarm
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A currents.
2. Connecting the Power Input
This section describes the functionalities of the VPN Gateway’s
components.
2.1 Upper Panel
The upper panel of the IVR-100 consists of one terminal block connector
within two DC power inputs.
Figure 2-1 shows the upper panel of the IVR-100 VPN Gateway.
DC Input:
9~48V , 1A max.
Fault
V1+ V2+
PWR2PWR1
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Figure 2-1: IVR-100 Upper Panel
The Upper Panel of the IVR-300 series consists of two terminal block
connectors.
− Green terminal block connector: Power 1, Power 2 input and relay
alarm output
− Yellow terminal block connector: 2 digital input and 2 digital output
Figure 2-2 shows the upper panel of the IVR-300/IVR-300W VPN
Gateway.
Max. Fault Alarm Loading: 24V, 1A
DI1 DO0 DO1DI0 GNDGND
V1+ V2+
PWR1
PWR2Alarm
DC Input:
9-54V
, 1.8A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 2-2: IVR-300/IVR-300W Upper Panel
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
1 2 3 4 5 6
Power 1 Fault Power 2
Alarm
+ - + -
Note
The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
Caution
PWR1 and PWR2 must provide the same DC voltage
while operating with dual power input.
2.5 Wi-Fi Antenna Installation (IVR-300W)
Step 1: Fasten the two dual-band antennas to the antenna connectors
on the front panel of the IVR-300W.
Step 2: Youcanbend theantennastotyouractualneeds.
Reset
RS485
P2
5G
P1
2.4G
Alarm
I/O
IVR-300W
WAN
WAN/LAN
LAN
5
3
1
4
2
1000
10/100
2.4G/5GHz
2.4G/5GHz
USB
GND
TxD+
RxD
Two Wi-Fi RP-SMA Connectors
Figure 2-4: IVR-300W Front Panel
3.3 Side Wall-mount Plate Mounting
4. Setup of the VPN Gateway
4.1 Requirements
Pleaseconrmthefollowingitemsbeforeconguration:
1.Please conrm the network is working properly: It is strongly
suggested to test your network connection by connecting your
computer directly to ISP.
2. Suggested operating systems: Windows 7/8/10.
3. Recommended web browsers: IE/Firefox/Chrome.