User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
3.3 DIN-rail Mounting Installation
The DIN rail is screwed on the Industrial Fast Ethernet
Switch when out of factory. When you need to replace
the wall mount application with DIN-rail application on
Industrial Fast Ethernet, please refer to the following gures
to screw the DIN rail on the Industrial Fast Ethernet Switch.
To hang the Industrial Fast Ethernet Switch, follow the
steps below:
Step 3: Check whether the DIN rail is tightly on the track.
Step 4: Please refer to the following procedures to remove
the Industrial Fast Ethernet Switch from the track.
1
2
Step 5: Lightly pull out the bottom of DIN rail to remove it
from the track.
3.4 Wall-mount Plate Mounting Installation
To install the Industrial Fast Ethernet Switch on the wall,
please follow the instructions described below.
Step 1: Remove the DIN rail from the Industrial Fast
Ethernet Switch; loosen the screws to remove the
DIN rail.
Step 1: Screw the DIN rail on the Industrial Fast Ethernet
Switch.
1
2
Step 2: Place the bottom of DIN rail lightly into the track.
Step 2: Place the wall-mount plate on the rear panel of
the Industrial Fast Ethernet Switch.
Step 3: Use the screws to screw the wall-mount plate on
the Industrial Fast Ethernet Switch.
Step 4: Use the hook holes at the corners of the wall-
mount plate to hang the Industrial Fast Ethernet
Switch on the wall.
Step 5: To remove the wall-mount plate, reverse the steps
above.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address :
[e-mail]
Copyright © PLANET Technology Corp. 2016.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product: 5/8-Port 10/100Mbps Industrial Ethernet Switch
*Model Number: ISW-501T, ISW-801T
* Produced by:
Manufacturer‘s
Name : Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive
on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (Class A:2010/AC:2011)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2008+A2:2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2013)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan 25 March, 2016
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]