User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial IP67-rated 8-Port
10/100Mbps M12 Ethernet Switch, ISW-800T-M12. In the
following sections, the term “Industrial M12 Ethernet Switch”
means the ISW-800T-M12.
Open the box of the Industrial M12 Ethernet Switch and
carefully unpack it. The box should contain the following items:
Industrial M12
Ethernet Switch x 1
User’s Manual x 1
1.2m M12-to-RJ45
UTP Cable x 1
1.2m M12 Power
Cable x 1
DIN-rail Kit x 1 Wall Mount Kit x 1
LED Indicators
Power LED: Power 1/Power 2 (Green),
FAULT (Green)
10/100BASE-TX Port (Port-1 to Port-8):
LNK/ACT (Green)
Network Cables
10BASE-T: 2-pair UTP Cat.3,4,5 up to
100m (328ft)
100BASE-TX: 2-pair UTP Cat.5, 5e, 6
up to 100m (328ft)
EIA/TIA-568 100-ohm STP (100m,
max.)
Switch Specications
Switch Processing
Scheme
Store-and-Forward
Address Table 2K entries
Flow Control
Back pressure for half duplex IEEE
802.3x Pause Frame for full duplex
Switch Fabric 1.6Gbps
Throughput
(packet per second)
1.19Mpps@64Bytes
Maximum Transmit
Unit
1536 bytes
3.2 M12 DC Power Cable Pinout
The Industrial M12 Ethernet Switch front panel provides one
M12 A-coded 5-pin male connector for DC power input; please
use the power cable with M12 A-coded 5-pin female connector
from Industrial M12 Ethernet Switch package for DC power
input. The Industrial M12 Ethernet Switch power input port
pinout is shown below:
INPUT
DC 9V~48V
Pinout 1: V1
-
Pinout 2: V1+
Pinout 3: V2+
Pinout 4: V2
-
ISW-800T-M12
V2
V2
V1
V1
3
4
2
1
Please follow the steps below for DC power cable installation on
Industrial M12 Ethernet Switch.
1. Plug the DC power cord connector to the power input port of
the Industrial M12 Ethernet Switch.
2. Screw the nut on DC power cord female connector to the
DC power input male connector of Industrial M12 Ethernet
Switch and make sure the connection is tight.
Note
Before DC power cord connection, please check
and assure your local DC power source is stable.
3. Hardware Introduction
3.1 Front Panel
The front panel of the Industrial M12 Ethernet Switch consists
of Ethernet interfaces and LED indicators.
 Front View
ACT
LNK
LNK/ACT
LNK/ACT
LNK/ACT
LNK/ACT
Fault
PWR 2
PWR 1
1
2
3
4
5
6
7
8
V2
V2
V1
V1
TX
RX
RX
TX
ISW-800T-M12
IP67 M12
DC Input:
9-48V
, 0.5A max.
Figure 3-1: ISW-800T-M12 Front View
If any of these pieces are missing or damaged, please contact
your dealer immediately; if possible, retain the carton including
the original packing material, and use them again to repack
the product in case there is a need to return it to us for repair.
2. Product Specications
Model ISW-800T-M12
Hardware Specications
10/100BASE-TX
Ports
8 x M12, 4-Pin D-coded female
connector
Power Connector
1 x M12, 5-Pin A-coded male
connector
Enclosure IP67 aluminum
Dimensions
(W x D x H)
103 x 53 x 163mm
Weight 976g
Power Requirements
9~48V DC, redundant power with
reverse polarity protection
Power Consumption/
Dissipation
4watts/13BTU
Installation DIN-rail kit and wall mount ear
ESD Protection 6KV DC
Standards Conformance
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3x Flow Control and Back
Pressure
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (Free fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~95%
(non-condensing)
Storage: 5~95%
(non-condensing)
 System LEDs
LED Color Function
PWR 1 Green Lit: To indicate power 1 has power.
PWR 2 Green Lit: To indicate power 2 has power.
Fault Green
Lit: To indicate either power 1 or power 2
has no power.
 10/100BASE-TX M12 Interface LEDs
LED Color Function
LNK/
ACT
Green
Lit: To indicate the Switch is successfully
connecting to the network at 10/100Mbps.
Blink: To indicate that the Switch is actively
sending or receiving data over that port.
O: To indicate the Switch is not
connecting to the network at 10/100Mbps.
3.3 10/100BASE-TX Ports with M12 Interface
Cable Pinout
The Industrial M12 Ethernet Switch front panel provides eight
RJ45 10/100BASE-TX ports and M12 interfaces. These ports
are designed for Ethernet equipment connection. The Industrial
M12 Ethernet Switch 10/100Mbps M12 input interface pinout is
shown below:
Pinout 1: TX+
Pinout 2: RX+
Pinout 3: TX
-
Pinout 4: RX -
ISW-800T-M12
TX
RX
RX
TX
1
4
2
3
RJ45 (8-Pin)
Pinouts for the RJ45 (8-Pin) Port
1 8
MDI MDI-X
Pin
1
2
3
6
Signal
TX+
TX
-
RX+
RX
-
RX+
RX
-
TX+
TX
-
Please follow the steps below for the 10/100Mbps M12 cable
installation of Industrial M12 Ethernet Switch.
1. Plug the 10/100Mbps M12 cable male connector to the
Ethernet female connector input port of the Industrial M12
Ethernet Switch.
2. Screw the nut on 10/100Mbps M12 cable male connector
to the Ethernet input female connector of Industrial M12
Ethernet Switch and make sure the connection is tight.