8-Port Managed Industrial Ethernet Switch ISW-800M User's Manual
Trademarks c PLANET Technology Corp. 2006. Copyright ○ Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Table of Contents 1. INTRODUCTION ................................................................................................................... 5 1.1 Packet Contents .............................................................................................................. 5 1.2 How to Use This Manual ................................................................................................. 5 1.3 Product Feature.................................................................................
.12 IP Configuration........................................................................................................... 35 4.13 SNTP Configuration .................................................................................................... 36 4.14 IP Security ................................................................................................................... 38 4.15 RSTP Configuration ............................................................................................
1. INTRODUCTION The 8-Port 10/100TX with redundant ring Web management industrial switch is a cost- effective solution and meets the high reliability requirements demanded by industrial applications. The switch can be easily managed through the Web GUI. It also provides the redundant ring function that can prevent the network connection failure. 1.
▫ CSMA/CD Protocol ▫ RJ-45 Port support auto MDI/MDI-X function ▫ 2K MAC address table ▫ 1Mbit memory buffer ▫ 2.
MAC address 2K Memory Buffer 1Mbit Network Cable 10Base-T : 2-pair UTP/STP Cat 3, 4, 5 cable 100Base-TX: 2-pair UTP/STP Cat. 5 cable 10Base-T: EIA/TIA-568 100-ohm (100m) LED Per port: Link/Activity (Green), Full duplex/Collision (Yellow) Per unit: Power (Green), Power 1 (Green), Power 2 (Green), Fault (Yellow), Master (Green) Back-plane 1.6Gbps Packet throughput ability 1.
128kbps, 256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB. Ingress filter packet type combination rules are Broadcast/Multicast/Unknown Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all of packet. The packet filter rate can be set follow as:1Mbps、2Mbps、4Mbps、 8Mbps、16Mbps、32Mbps、64Mbps. Port mirror Support TX packet only or both of TX and RX packet. Packet filter 4 selection rules for different type of packet combination: 1. All of packet 2.
2. HARDWARE INSTALLATION This section describes the functionalities of the Switch's components and guides how to install it on the rack or mount to the wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description The PLANET Management Industrial Ethernet Switch provides substation hardened, fully managed, Ethernet switches specifically designed to operate reliably in electrically and environmentally harsh environments.
Figure 2-1 ISW-800M Front Panel 2.1.3 LED Indications LED Status Meaning Green The switch unit is power on. Off The switch unit is no power input. Green Power on Off No power inputs Green Power on Off No power inputs Yellow Power failure or UTP port failure or Fiber port failure Off No Power failure or UTP port failure or Fiber port failure occurs R. M. Green The industrial switch is the master of redundant ring group.
FDX/COL Off No device attached Yellow The port is operating in full-duplex mode. Blinks Collision of Packets occurs in the port. Off The port in half-duplex mode or no device attached (Port 7 & 8) 2.1.4 Reset Button The reset button provides user a quick and easy way to restart and set the configuration back to default value. 。 Restart: press the button for 2 seconds and release. 。 Set to factory default value: press the button for 5 seconds and release.
OFF 6 ON OFF 7 ON OFF 8 ON OFF 9 ON Disable port 6 Alarm Enable port 6 Alarm. If the port’s link fails, the fault LED will light up. Disable port 7 Alarm Enable port 7 Alarm. If the port’s link fails, the fault LED will light up. Disable port 8 Alarm Enable port 8 Alarm. If the port’s link fails, the fault LED will light up. Disable the ring master function. Enable the switch as the ring master in the redundant ring group. [NOTE] 1.
V- V+ V- V+ 1. Insert the positive and negative wires into the V+ and V- connector on the terminal block connector. 2. To tighten the wire-clamp screws for preventing the DC wires to loose. Power Notice: The wire range of terminal block is from 12~ 24 AWG. 2.1.8 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as below figure shows.
Fault Alarm Contact The open circuit will form when the power failure or port link failure. 24V DC Buzzer 24V Battery The fault alarm device will send a warning signal t warn the user, ex: alarm sound or flash light. 2.2 Mounting Installation This section describes how to install the Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. 2.2.
Step2: Lightly push the button of DIN-Rail into the track. Step3: Check the DIN-Rail is tightly on the track. Step4: To remove the industrial switch from the track, reverse steps above. 2.2.2 Wall Mount Plate Mounting To install the switch on the wall, please follows the instructions described below. Step1: Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-Rail. Step2: Place the wall mount plate on the rear panel of the industrial switch.
Step3: Use the screws to screw the wall mount plate on the industrial switch. Step4: Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall. Step5: To remove the wall mount plate, reverse steps above.
3. NETWORK INSTALLATION 3.1 Hardware Installation In this paragraph, we will describe how to install the 8-Port 10/100TX with redundant ring Web management industrial switch and the installation points for attention. 1. Unpacked the Industrial switch. 2. Check the DIN-Rail is screwed on the Industrial switch. If the DIN-Rail is not screwed on the Industrial switch. Please refer to DIN-Rail Mounting section for DIN-Rail installation.
3.3 Redundant Ring Application The industrial switch supports the redundant ring protocol that can help your network system to recovery from network connection failure within 300ms or less, and make your network system more reliable. The redundant ring algorithm is like as spanning tree protocol (STP) algorithm but it has faster recovery time than STP. The following figure is a sample redundant ring application.
3.4 Coulping Ring Application In the network, it may have more than one redundant ring group. By using the coupling ring function can connect each redundant ring for the redundant backup. It can ensure the transmissions between two ring groups will no failure. The following figure is a sample of coupling ring application.
3.5 Dual Homing Application Dual Homing function is to prevent the connection lose between redundant ring group and upper level/core switch. Assign two ports to be the Dual Homing ports that one is working port and one is backup port in the redundant ring group. The backup port that has smaller MAC address value will be selected by switch automatically. The Dual Homing function only work when the redundant ring function is active. The maximum Dual Homing port is two in a redundant ring group.
4. WEB MANAGEMENT This section introduces the configuration and functions of the Web-Based management. The following configuration steps are based on the firmware version 1.00. 4.1 About Web-based Management Inside the CPU board of the switch exists an embedded HTML web site residing in flash memory. It offers advanced management features and allow users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer.
The Web management interface 4.4 Port Status In Port status, you can view every port status that depended on user's setting and the negotiation result. 。 Port: the port number. 。 Type: the speed mode, ex: 100TX = 100Mbps. 。 Link: "Down" is "No Link". "UP" is "Link". 。 State: display port statuses "disable" or "enable". "Unlink" will be treated as "off ". 。 Negotiation: display the auto negotiation mode: auto/force. "Config" means the value that user configured.
4.5 Single port information You can click the port on the Panel figure on the left side of web GUI. Then, the single port information window will pop up and display the port current status information. Port information interface 4.6 Port Statistics The following information provides a view of the current port statistic information.
to clean all counts. Port Statistics Interface 4.7 Port Control You can change the port status. 1. Select the port by scroll the Port column. 2. State: disable or enable control of his port. 3. Negotiation: you can set auto negotiation mode is Auto, Nway (specify the speed/duplex on this port and enable auto-negotiation), or Force. 4. Speed: set the speed of the port. 5. Duplex: set full-duplex or half-duplex mode of the port. 6.
Port Control interface 4.8 Switch Settings You can assign the system name and location and view the system information. 。 System Name: assign the name of switch. The maximum length is 64 bytes. 。 System Location: assign the switch physical location. The maximum length is 64 bytes. 。 System Description: display the description of switch. Read only cannot be modified. 。 Firmware Version: display the switch's firmware version. 。 Kernel Version: display the kernel software version.
Switch Settings interface [NOTE] Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. 4.9 Port Mirroring The Port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port. That is, traffic goes in or out monitored ports will be duplicated into mirror port. 1. Port Mirroring Mode: set mirror mode -- Disable, TX, and Both. The default is "Disable". 2.
Port Mirroring intrerface 4.10 VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all the network devices are still plug into the same switch physically.
VLAN Configuration interface 4.10.1 Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored.
VLAN – Port-based Add interface 6. You will see the VLAN group displays. 7. If the groups' list is more than one page, you can click 8. Use button to delete unwanted VLAN. 9. Use button to modify existing VLAN group. to view other VLAN groups. [NOTE] Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. 4.10.2 802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard.
802.1Q VLAN interface 4.10.2.1 Basic Add 1. Click button. 2. Management VLAN ID: it is used for remote management security. Only the port of VLAN group ID is equal to the Management VLAN ID can remote management that include telnet, SNMP, and Web browse the switch. Fill the specific VLAN ID number in Management VLAN ID column and mark the check box, and then click button to enable the function. For example: the management VLAN ID is 101, the VLAN group ID 101 includes the port 1, 2, and 4.
802.1Q VLAN – Add interface 6. Click . Then you will see the page as follow.
7. To set the outgoing frames are VLAN-Tagged frames or untagged. Then click . 。 Tag: outgoing frames with VLAN-Tagged. 。 Untag: outgoing frames without VLAN-Tagged. 4.10.2.2 Port VID: Configure port VID settings 1. Port VLAN ID: enter the port VLAN ID. 2. Click 3. To reset back to default value, click . button. 802.1q VLAN - Port VLAN ID interface [NOTE] Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. 4.
user. You can set up the mail server IP, mail account, and forwarded email account for receiving the event alert. 1. Email Alert: enable or disable the email alert function. 2. SMTP Server IP Address: set up the mail server IP address. 3. Authentication: mark the check box to enable and configure the email account and password for authentication. 。 Mail Account: set up the email account to receive the alert. Ex: johnadmin@123.com.
alert to the dedicate SMTP server. ¾ Power status: when the device power status has changed, the system will send out the alert to the dedicate SMTP server. ¾ SMNP Authentication Failure: when the SNMP authentication fail, the system will send out the alert to the dedicate SMTP server. ¾ Redundant Ring topology change: when the redundant ring topology has changed, the system will send out the alert to dedicate SMTP server. ■ Port event selection: select the per port events.
Power Alarm interface 4.12 IP Configuration Power alarm function enables the Relay alarm action. Without enabling power alarm function, the Relay alarm action will not work even the Relay alarm is set. Mark the check box and click button. ■ DHCP Client: Enable or Disable the DHCP client function. When DHCP client function is enabling, the industrial switch will be assigned the IP address from the network DHCP server. The default IP address will be replace by the DHCP server assigned IP address.
IP Configuration interface 4.13 SNTP Configuration You can configure the SNTP (Simple Network Time Protocol) settings. The SNTP allows you to synchronize switch clocks in the Internet. 1. SNTP Client: enable or disable SNTP function to get the time from the SNTP server. 2. UTC Timezone: set the switch location time zone. The following table lists the different location time zone for your reference.
ALA - Alaskan Standard -9 hours 3 am HAW - Hawaiian Standard -10 hours 2 am Nome, Alaska -11 hours 1 am +1 hour 1 pm +2 hours 2 pm BT - Baghdad, USSR Zone 2 +3 hours 3 pm ZP4 - USSR Zone 3 +4 hours 4 pm ZP5 - USSR Zone 4 +5 hours 5 pm ZP6 - USSR Zone 5 +6 hours 6 pm WAST - West Australian Standard +7 hours 7 pm CCT - China Coast, USSR Zone 7 +8 hours 8 pm JST - Japan Standard, USSR Zone 8 +9 hours 9 pm +10 hours 10 pm +12 hours Midnight CET - Central European FWT - Fren
SNTP Configuration 4.14 IP Security IP security function allows you to assign 10 specific IP addresses that have permission to access the switch through the web browser for the securing switch management. 1. Enable the IP Security: mark the check box to enable the IP security function. 2. Security IP 1 ~ 10: you can assign up to 4 specific IP address. Only these 4 IP address can access and manage the switch through the Web browser. 3. Click button to apply the configuration.
IP Security interface 4.15 RSTP Configuration The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto detect the connected device that is running STP or RSTP protocol. 4.15.1 System Configuration 1. You can view spanning tree information about the Root Bridge. 2. You can modify RSTP state. After modification, click button.
Rapid Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a value between 4 through 30. [NOTE] 1. Must follow the rule to configure the MAX Age, Hello Time, and Forward Delay Time. 2 x (Forward Delay Time value -1) > = Max Age value >= 2 x (Hello Time value +1) 2. Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. RSTP – System Configuration interface 4.15.
mathematic calculation. False is including the STP mathematic calculation. 7. Click button. [NOTE] Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. RSTP – Per Port Configuration interface 4.16 Redundant Ring Redundant ring provide a faster redundant recovery than Spanning Tree topology. The action is similar with STP or RSTP, but the algorithms not the same.
The system also supports the coupling ring that can connect 2 or more redundant ring group for the redundant backup function and dual homing function that prevent connection lose between redundant ring group and upper level/core switch. ■ Enable Redundant ring: to enable the redundant ring function. Marking the check box to enable the redundant ring function. ■ 1st & 2nd Working Ports: assign two ports as the member ports. One port will be working port and one port will be the backup port.
[NOTE] 1. When you enable the redundant ring function, you must disable the RSTP. The redundant ring function and RSTP function cannot exist at the same time. 2. Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the switch power off. 4.17 QoS Configuration You can configure Qos setting of the every port. ■ Oos Policy: select the Qos policy rule.
QoS Configuration interface 4.18 IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries and report packets and manage IP multicast traffic through the switch.
IGMP Snooping interface 4.19 SNMP Configuration The SNMP is a Protocol that governs the transfer of information between management and agent. The switch supports SNMP V1. You can define management stations as trap managers and to enter SNMP community strings. You also can define a name, location, and contact person for the switch. Fill in the system options data, and then click Apply to update the 4.19.1 System Operations 1. Name: enter a name for the switch. 2.
4.19.3 Trap Manager A trap manager is a management station that receives traps, the system alerts generated by the switch. If no trap manager is defined, no traps will issue. Create a trap manager by entering the IP address of the station and a community string. 1. IP Address: fill in the trap device IP. 2. Community Strings: the trap device community strings. 3. Trap version: the trap has two versions - v1 or v2, select one of them. 4. Click . SNMP Management interface 4.
Security Manager interface. 4.21 Configuration Backup In Configuration Backup, you can restore the backup configuration into the industrial switch. Also, you can backup the configuration to TFTP server. 4.21.1 TFTP Restore Configuration You can restore flash ROM value from TFTP server, but you must put the backup image in TFTP server, industrial switch will download the image back to the flash. 1. TFTP Server IP Address: fill in the TFTP server IP. 2.
TFTP Restore Configuration interrface 4.21.2 TFTP Backup Configuration You can save current flash ROM value from the industrial switch to the TFTP server, then go to the TFTP restore configuration page to restore the image value back to the industrial switch. 1. TFTP Server IP Address: fill in the TFTP server IP 2. Backup File Name: fill the file name 3. Click .
4.21.3 TFTP Update Firmware It provides the functions to allow a user to update the switch firmware. Before updating, make sure you have your TFTP server ready and the firmware image is on the TFTP server. 1. TFTP Server IP Address: fill in your TFTP server IP. 2. Firmware File Name: the name of firmware image. 3. Click . TPTP Update Firmware interface 4.22 Factory Default Reset Switch to default configuration.
Factory Default interface 4.23 Save Configuration Save the industrial switch configuration to the flash memory. Power off the industrial switch without the saving, all changed configuration will lost. Click the Save Configuration interface button the save the configuration.
4.24 System Reboot Reboot the Switch in software reset. Click button to reboot the switch. System Reboot interface 4.25 Rate Control You can set up every port's bandwidth rate and packet limitation type. ■ Limit Packet type: select the packet type that want to filter. The packet types have all type packet, broadcast/multicast/unknown unicast packet, broadcast/multicast packet, and broadcast packet only.
2. Qos and Rate control cannot be existed at the same. Rate Control interface 4.26 System Log You can set up system log events and view the system log events. 4.26.1 System Log Configuration You can view the system log events in here. Click button to get newest system log event and button to clear the log events. If log event list more that one page, drag down the list to switch to different page. ■ System Log Client Mode: you can select in Client Only, Server Only, or Both mode.
System Log Configuration 4.26.2 Event Configuration You can select the system log events. When selected events occur, the system will send out the log information. Also, per port log events can be selected. ■ System event selection: 4 selections - Device cold start, Power status, SNMP Authentication Failure, and Redundant ring topology change. Mark the checkbox to select the event. When selected events occur, the system will produce the logs.
Event Configuration interface
5. TROUBLESHOOTING This section is intended to help you solve the most common problems on the industrial Ethernet switch. 5.1 Incorrect connections The switch port can auto detect straight or crossover cable when you link switch with other Ethernet device. For the RJ-45 connector should use correct UTP or STP cable, 10/100Mbps port use 2-pairs twisted cable. If the RJ-45 connector is not correct pin on right position then the link will fail.
IF the power indicator does turn on when the power cord is plugged in, you may have a problem with power outlet, or power cord. However, if the Switch powers off after running for a while check for loose power connections, power losses or surges at power outlet. IF you still cannot resolve the problem, contact your local dealer for assistance. 5.2.
6. APPENDIX 6.1 100BASE-TX/10BASE-T Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. RJ-45 Pin Assignments Pin Number Assignment 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- Note: "+" and "-" signs represent the polarity of the wires that make up each wire pair. All ports on this switch support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs.
