ISW-514PTF(V3) User Manual

ManualsBrandsPLANET Technology ManualsPoE switchesIP30 Industrial Ethernet Switch 4-Port 10/100Mbps with PoE + 1-Port 100Base-FX (MM, SC, 2km) (-40 ~ 75C)

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 5-Port Industrial Ethernet

Switch with 4-Port PoE, ISW-504PT/ISW-514PTF. The interfaces

of these models are shown below:

Model Name

10/100Mbps RJ45

Ports

100FX SFP Slots PoE Ports

ISW-504PT 5 - 4

ISW-514PTF 4 1 4

In the following section, the term “Industrial PoE+ Switch”

means the ISW-504PT/ISW-514PTF.

2. Hardware Introduction

2.1 Switch Front Panel

P1 P2 Fault

120W

PoE Usage

90W

60W

30W

LNK ACT

PoE-in-Use

ISW-504PT

挖孔

10/100TX

LNK/

ACT

DIP

1~4

VLAN

Extended

OFF

Standard

1 2 3 4 5

ONDIP

LNK ACT

PoE-in-Use

ISW-514PTF

挖孔

P1 P2 Fault

100FX

DIP

1~4

VLAN

Extended

OFF

Standard

120W

PoE Usage

90W

60W

30W

1 2 3 4 5

ONDIP

Figure 2-1:

ISW-504PT front panel

Figure 2-2:

ISW-514PTF front panel

1. Fast Ethernet TP Interfaces

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

2.3 Switch Upper Panel

The upper panel of the Industrial PoE+ Switch consists of one

terminal block connector within two DC power inputs.

Figure 2-3 shows the upper panel of the Industrial PoE+ Switch.

Input DC 12~48V

Fault max.

load 1A@24V

FaultDC1 DC2

1 2 3 4 5 6

Figure 2-3: Industrial PoE+ Switch Upper Panel

2.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial PoE+ Switch is used for two DC redundant power

inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like

inserting the wires or tightening the wire-clamp

screws, make sure the power is OFF to prevent

from getting an electric shock.

2.2 LED Indicators

System

LED Color Function

P1 Green Lights: indicates power 1 has power.

P2 Green Lights: indicates power 2 has power.

FAULT Red

Lights: indicates either power 1 or power 2

has no power.

30W Amber

O: indicates the PoE usage is less than

14W.

Blinks: indicates that the PoE usage is

around 15W to 29W.

Lights: indicates the PoE usage is around/

over 30W.

60W Amber

Blinks: indicates that the PoE usage is

around 45W to 59W.

Lights: indicates the PoE usage is around/

over 60W.

90W Amber

Blinks: indicates that the PoE usage is

around 75W to 89W.

Lights: indicates the PoE usage is around/

over 90W.

120W Amber

Blinks: indicates that the PoE usage is

around 100W to 119W.

Lights: indicates the PoE usage is at the

maximum.

Open the box of the Industrial PoE+ Switch and carefully

unpack it. The box should contain the following items:

Industrial PoE+ Switch x 1 User’s Manual x 1

Dust Cap x 5 Wall-mount Kit x 1

If any of these are missing or damaged, please contact your

dealer immediately.

2. 100BASE-FX SFP Slot (ISW-514PTF)

100BASE-FX mini-GBIC slot, SFP (small form-factor plug-

gable) transceiver module: From 2 kilometers (multi-mode

ber) to 20/40/60 kilometers (single-mode ber).

3. DIP Switch

The Industrial PoE+ Switch provides one DIP switch for

Standard, VLAN and Extended mode selections. The

detailed descriptions are shown in the following table.

DIP Switch

Mode

Function

Standard

Switches 1 to 5 are o.

This mode makes the Industrial PoE+ Switch

operate as a general switch and all PoE ports

operate at 10/100Mbps auto-negotiation.

VLAN

Switch 5 is on.

This mode makes the Industrial PoE+ Switch

operate as a VLAN isolation switch and

1. Ports 1 to 4 will isolate respectively.

2. Ports 1 to 4 can only communicate with Port 5.

Note

After adjusting VLAN DIP switch,

reboot the Industrial PoE+ Switch to

make the change take effect.

Extended

Any of switches 1 to 4 is on.

This mode makes the Industrial PoE+ Switch

operate on a per-port basis at 10Mbps full duplex

operation but can support IEEE 802.3af PoE power

output over a distance of up to 250 meters

overcoming the 100m limit on Ethernet UTP cable.

 Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1

to Port 4)

LED Color Function

LNK/

ACT

Green

Lights: indicates the link through that port

is successfully established at 10Mbps or

100Mbps.

Blinking: indicates that the switch is

actively sending or receiving data over that

port.

PoE-

in-Use

Amber

Lights: indicates the port is providing DC

in-line power.

O: indicates the connected device is not a

PoE powered device (PD).

 Per 10/100BASE-TX Interface (Port 5 of ISW-504PT)

LED Color Function

LNK/

ACT

Green

Lights: indicates the link through that port is

successfully established at 10/100Mbps.

Blinking: indicates that the switch is actively

sending or receiving data over that port.

 Per 100FX SFP Slot (Port 5 of ISW-514PTF)

LED Color Function

LNK/

ACT

Green

Lights: indicates the link through that port is

successfully established at 100Mbps.

Blinks: indicates that the switch is actively

sending or receiving data over that port.

1. The DC power input range is 12V ~ 48V DC. Please insert

positive and negative DC power wires into contacts 1 and 2

for POWER 1, or 5 and 6 for POWER 2.

Input DC 12~48V

Fault max.

load 1A@24V

FaultDC1 DC2

1 2 3 4 5 6

DC Input Max. PoE Budget

12V 60W

24V 90W

48V 120W

Note

To avoid damage, please use the Industrial PoE+

Switch under its specification.

Summary of content (2 pages)

PAGE 1
. Package Contents 2. Hardware Introduction Thank you for purchasing PLANET 5-Port Industrial Ethernet Switch with 4-Port PoE, ISW-504PT/ISW-514PTF. The interfaces of these models are shown below: 2.
PAGE 2
. Tighten the wire-clamp screws for preventing the wires from loosening. 3. Installation This section describes the functionalities of the Industrial PoE+ Switch’s components and guides you to installing it on the DIN-rail and wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. Note 1 2 Power 1 + - 3 4 The installation procedures of the ISW-504PT and ISW-514PTF are the same as they are shown below. 5 6 Power 2 + - Fault 3.