4-Port 10/100Mbps +1/2 100FX Fiber Port Industrial Fast Ethernet Switch ISW-511 / ISW-621 Series ISW-511T / ISW-621T Series User's Manual
Trademarks Copyright © PLANET Technology Corp. 2015 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp. other trademarks belong to their respective owners. All Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications.
Table of Contents 1. Introduction............................................................................... 6 1.1 Package Contents................................................................. 6 1.2 How to Use This Manual........................................................ 6 1.3 Product Features.................................................................. 7 1.4 Product Specifications........................................................... 8 2. Installation................................
4. Switch Operation.......................................................................27 4.1 Address Table......................................................................27 4.2 Learning.............................................................................27 4.3 Forwarding & Filtering..........................................................27 4.4 Store-and-Forward...............................................................28 4.5 Auto-negotiation...........................................
1. Introduction 1.1 Package Contents Check the contents of your package for the following parts: zz Industrial Fast Ethernet Switch x 1 zz User's Manual x 1 zz DIN Rail Kit x 1 zz Wall Mount Kit x 1 If any of these are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair 1.
1.3 Product Features Physical Port Ports Model Name Copper ISW-511 ISW-511S15 ISW-511TS15 ISW-621T ISW-621S15 Mode Distance Multi-mode 2km 1x 100BASE-FX Single15km mode ISW-511T ISW-621 Fiber Optical Interface Optical 4x 10/100BASE-TX ISW-621TS15 ISW-621TF Multi-mode 2km Single2x mode 100BASE-FX Multi / Single Mode 15km depending on SFP Module Layer 2 Features Complies with IEEE 802.3, IEEE 802.
Industrial Case / Installation IP30 metal case DIN rail and wall mount design 12 to 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave power -10 to 60 degrees C operating temperature on ISW-511 / ISW511S15 / ISW-621 / ISW-621S15 -40 to 75 degrees C operating temperature on ISW-511T / ISW511TS15 / ISW-621T / ISW-621TS15 / ISW-621TF 1.
Switch Specifications Switch Processing Scheme Store-and-Forward Address Table 2K entries Buffer 1Mbit Flow Control Back pressure for half duplex, IEEE 802.3x pause frame for full duplex Switch Fabric 1Gbps Throughput (Packet Per Second) 0.74Mpps @ 64Bytes Standards Conformance Standards Compliance IEEE 802.3 Ethernet, 10BASE-T IEEE 802.3u Fast Ethernet, 100BASE-TX, 100BASE-FX IEEE 802.
Fiber Optical Port 1 x 100BASE-FX Cable 50/125μm fiber 62.5/125μm fiber 9/125μm fiber Mode multi-mode single-mode Distance 2km 15km Dimensions (W x D x H) 135 x 97 x 32mm Weight 436g Power Requirements 12~48V DC, Redundant power with polarity reverse protection function Power Consumption / Dissipation 13.
Temperature Operating: -40~75 degrees C Storage: -40~85 degrees C Humidity Operating: 5% to 90%, Storage: 5% to 90% (non-condensing) Regulation Compliance FCC Part 15 Class A, CE Model ISW-621 ISW-621S15 Hardware Specifications Ports 4 x 10/100BASE-TX, auto-negotiation, auto-MDI/ MDI-X Cable 10BASE-T : 2-pair UTP Cat. 3, 4, 5 cable (100 meters, max.) 100BASE-TX : 2-pair UTP Cat. 5, 5e, 6 cable (100 meters, max.) Port 2 x 100BASE-FX Cable 50/125μm fiber 62.
Flow Control Back pressure for half duplex, IEEE 802.3x pause frame for full duplex Switch Fabric 1.2Gbps Throughput (Packet Per Second) 0.89Mpps @ 64Bytes Standards Conformance Standards Compliance IEEE 802.3 Ethernet, 10BASE-T IEEE 802.3u Fast Ethernet, 100BASE-TX, 100BASE-FX IEEE 802.
Dimensions (W x D x H) 135 x 97 x 32mm Weight 442g Power Requirement 12~48V DC, Redundant power with polarity reverse protection function Power Consumption / Dissipation 16 watts / 54BTU Installation DIN rail kit and wall mount ear Switch Specification Switch Processing Scheme Store-and-Forward Address Table 2K entries Buffer 1Mbit Flow Control Back pressure for half duplex, IEEE 802.3x pause frame for full duplex Switch Fabric 1.2Gbps Throughput (Packet Per Second) 0.
2. Installation This section describes the functionalities of the Industrial Fast Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.
2.1.1 Switch Front Panel Figures 2-1, 2-2, 2-3 and 2-4 show their front panels.
P1 P2 FAULT P1 P1 P2 FAULT P2 FAULT TX 100 100 LNK/ACT TX 100 LNK/ACT 10/100 LNK/ACT RX 6 LNK/ ACT TX 100 5 RX 100 LNK/ACT 5 5 RX LNK/ ACT 4 4 4 3 3 3 2 2 2 1 1 1 ISW-511T Figure 2-3 ISW-511T / ISW-511TS15 Front Panel 16 6 10/100 LNK/ACT ISW-621T Figure 2-4 ISW-621T / ISW-621TS15 Front Panel 10/100 LNK/ACT ISW-621TF Figure 2-5 ISW-621TF Front Panel
2.1.2 LED Indicators LED Color Function P1 Green Lit: indicates power 1 has power. P2 Green Lit: indicates power 2 has power. FAULT Green Lit: indicates either power 1 or power 2 has no power. 100 Green Fiber Optic Lit: indicates the Fiber port is successfully connecting to the network at 100Mbps. Copper Lit: indicates the Switch is successfully connecting to the network at 100Mbps. Off: indicates that the Switch is successfully connecting to the network at 10Mbps.
2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Fast Ethernet Switch is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. V1- V1 + V2 - V2 + 2. Tighten the wire-clamp screws for preventing the wires from loosening.
Note The wire gauge for the terminal block should be in the range between 12 and 24 AWG. 2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Fast Ethernet Switch will detect the fault status of the power failure, or port link failure (available for managed model) and then forms an open circuit.
2.2 Mounting Installation This section describes how to install the Industrial Fast Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. Note In the installation steps below, this Manual uses IGS-801 (PLANET 8-Port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Switch and Industrial Media Converter are similar. 2.2.
1 2 Step 2: Lightly insert the bottom of the switch into the track. Step 3: Check whether the DIN-rail is tightly on the track. Step 4: Please refer to the following procedures to remove the Industrial Fast Ethernet Switch from the track. 2 1 Step 5: To remove the wall mount plate, reverse the steps above.
2.2.2 Wall Mount Plate Mounting To install the Industrial Fast Ethernet Switch on the wall, please follow the instructions described below. Step 1: To remove the DIN-Rail from the Industrial Fast Ethernet Switch; loosen the screws to remove the DIN-rail. Step 2: Place the wall mount plate on the rear panel of the Industrial Fast Ethernet Switch. Step 3: Use the screws to screw the wall mount plate on the Industrial Fast Ethernet Switch.
3. Applications In this paragraph, we will describe how to install Industrial Fast Ethernet Switch and the installation points for the attention.
Weather Station IP Camera ISW-511TS15 Desert IP Camera ISW-511TS15 15km 100 100 15km IP Camera IP Camera Fiber Switch 15km 100 Data Center 15km ISW-511TS15 100 IP Camera 15km ISW-511TS15 100 ISW-511TS15 ISW-511T Steel Factory Winter season of Country 100Base-FX Fiber-optic 100 100Base-TX UTP Weather Station IP Camera Desert IP Camera IP Camera IP Camera 15km 100 ISW-621TS15 ISW-621TS15 15km 100 Fiber Switch 100 15km Data Center 15km 100 ISW-621TS15 15km IP Camera IP C
Weather Station IP Camera Desert IP Camera IP Camera IP Camera 20km (Single mode) 100 ISW-621TF ISW-621TF 100 20km (Single mode) Fiber Switch 100 60km (Single mode) Data Center 2km (Multi-mode) 100 ISW-621TF IP Camera IP Camera 2km (Multi-mode) 2km (Multi-mode) 100 ISW-621TF Winter season of Country 100 ISW-621TF Steel Factory 100 ISW-621TF 100Base-FX Fiber-optic 100Base-TX UTP 25
Installation Steps Step 1: Unpack the Industrial Fast Ethernet Switch. Step 2: Check whether the DIN-rail is screwed on the Industrial Fast Ethernet Switch. (Please refer to DIN-rail mounting section for DIN-rail installation. If you want to wallmount the Industrial Fast Ethernet Switch, then please refer to the Wallmount Plate Mounting section for wallmount plate installation.
4. Switch Operation 4.1 Address Table The Industrial Fast Ethernet Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of some node in the network, including MAC address, port no., etc. This information comes from the learning process of Industrial Fast Ethernet Switch. 4.
4.4 Store-and-Forward Store-and-Forward is one type of packet-forwarding techniques. A Store-and-Forward Industrial Switch stores the incoming frames in an internal buffer and checks any error from the frames before transmission. No error packets occurrence, it is the best choice when a network needs efficiency and stability.
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Fast Ethernet Switch is not functioning properly, make sure the Industrial Fast Ethernet Switch was set up according to instructions in this manual. The Link LED is not lit Solution: Check the cable connection of the Industrial Fast Ethernet Switch. Link LED is lit, but the traffic is irregular Solution: Check whether the attached device is not set to dedicated full duplex.
APPENDIX A: Networking Connection A.
A.2 RJ45 cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : : 4+1 / 4+2 100FX Port Industrial Ethernet Switch ISW-511 / ISW-511S15 / ISW-511T / ISW-511TS15 ISW-621 / ISW-621S15 / ISW-621T / ISW-621TS15 / ISW-621TF * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
