User's Manual
- 1 - - 2 - - 3 - - 4 -
1. Package Contents
Thank you for purchasing PLANET Industrial IP67 1-port 10/100/1000T
802.3bt PoE++ to 2-port 10/100/1000T 802.3at/bt PoE++ Extender,
IPOE-E302. In the following sections, the term “Outdoor PoE
Extender” means the IPOE-E302.
Open the box of the Industrial PoE Extender and carefully unpack it. The
box should contain the following items:
IPOE-E302 x 1
M22 Waterproof
Cable Gland x 3
Spanner x 1
User’s Manual x 1 Wall-mounted Kit x 1 Ground Wire x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
2. Hardware Introduction
This section describes the functionalities of the Outdoor PoE Extender’s
components.
2.1 Product Outlook
Unit: mm
LAN
LAN
LAN
PoE++ In
PoE++ Out
IPOE-E302
Figure 2-1: IPOE-E302 product outlook
2.2 802.3bt PoE++ Input Port
Figure 2-2 shows the PoE++ Input port side of the IPOE-E302
Figure 2-2: IPOE-E302 PoE++ Input port side
2.3 802.3at/bt PoE+ Output Port
Figure 2-3 shows the two PoE++ ouput ports side of the IPOE-E302.
Figure 2-3: IPOE-E302 PoE++ Output ports side
2.4 LED Indicators
LED Color Function
LNK/ACT Green
Lights to indicate the port is linked up at
10/100/1000Mbps.
Blinks to indicate that the IPOE-E302 is actively
sending or receiving data over that port.
3. Installation
This section describes how to install the Outdoor PoE Extender and
make connections to it. Please read the following sections and perform
the procedure in the order being presented.
3.1 Installing Cable Gland with RJ45 UTP Cable
The cable gland consists of the following
A. Clamping Nut
B. Sealing Insert
C. Body (with Rubber Washer)
3.2 Connecting Waterproof Cable Kit to the Outdoor
PoE Extender
Step 1: Turn clockwise to tighten the gland body connected to the
Outdoor PoE Extender.
Step 2: Plug the RJ45 connector into the connector of the PoE++ In
port.
3.3 Wall-mount Installation
To install the Outdoor PoE Extender on the wall, please follow the
instructions described below.
Step 1: Find the wall that you want to mount the Outdoor PoE
Extender on.
Step 2: Refer to the picture below to screw the four screws on the wall.
140.00mm
129.00mm
60.00mmØ
4.50mm
Ø7.00mm
Step 3: Use a screwdriver to screw them into the wall.
3.4 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a
sudden lightning could cause fatal damage to the device.
Earth Ground
Note
EMD (Lightning) DAMAGE IS NOT CONVERED UNDER
WARRANTY.
3.5 Connecting IPOE-E302 to PSE
The Outdoor PoE Extender has three RJ45 ports of which one is the
PoE++ In port connected to the PSE and the other two are PoE+/
PoE++ Out ports connected to the PDs.
Step 1: Connect a standard Cat5e/6 UTP cable from a remote PSE,
such as PoE switch, to the “PoE++ In” port of the IPOE-
E302.
Power
Data
100m
802.3bt PoE Switch (PSE)
IPOE-E302
Step 2: The PSE delivers both Ethernet Data and PoE power over UTP
cable to the IPOE-E302 and the “LAN” LED will be lit steadily.
Note
1. If the LED is not lit, please check the remote PSE or
the cable connecting to a PC or a network device to
see if the cable is correct. Or with an 802.3at/bt
device such as the target PD, check whether the power
injection is correct.
2. Never connect any non-standard PoE PSE to the
IPOE-E302; it will damage the device permanently.
Step 3: Insert the sealing insert into the cable gland body.
Step 4: Attach the clamping nut to the cable gland to complete the
cable assembly.
Caution
Make sure the clamping nut is tightly attached to the
cable gland body and the sealing insert is squeezed
tightly.
Step 5: Repeat Steps 1 to 4 for two PoE++ Out ports.
Note
1. Use only the waterproof cable gland provided in the
package of the IPOE-E302.
2. If the above installation procedure is not properly
followed, the warranty will be invalidated.
11.31mm
40.78mm
5.00mm
30.22mm
29.80mm
20.18
13.72
14.00
30.10
3. If the waterproof cable gland is found missing or
damage, please contact your local reseller where you
purchased from.
4. Never use any waterproof cable gland that is not
purchased from PLANET or doesn’t have the same
dimensions of the IPOE-E302; it will damage the device
permanently.