User's Manual

- 5 - - 6 - - 7 - - 8 -
3.6 Connecting IPOE-E302 to PD
Step 1: Connect the additional Cat5e/6 cable from the PoE++ Out of
the IPOE-E302 to a remote PD.
PoE Wireless AP
PoE Camera
IPOE-E302
Power
Data
100m
Power
Data
100m
Step 2: The PoE++ Out port is also the power injector which
transmits DC voltage to the Cat5e/6 cable and transfer data
and power simultaneously between the PSE and PD.
Step 3: Once the IPOE-E302 detects the existence of an IEEE 802.3at/
bt device or Ethernet device, the LAN LED indicator will be lit
steadily, showing it is providing power.
60-95W
30W
PoE Dome IP Camera
802.3bt PoE++
802.3at PoE+
Power
Data
100m
100m
802.3at PoE+
100m
PoE Dome IP Camera
802.3af PoE
100m
802.3af PoE
100m
30W+30W
PoE Extender
802.3bt PoE++ Injector/Switch
1 In 2 Out
802.3at PoE+
Power
Data
100m
10W+10W
802.3at PoE+ Injector/Switch
60-95W
PoE Dome IP Camera
802.3bt PoE++
Power
Data
100m
802.3bt PoE++
100m
60W
PoE Extender
802.3bt PoE++ Injector/Switch
1 In 1 Out
PoE Extender
1 In 2 Out
Note
1. Due to the limitation of PoE budget, if the bt (PoE++)
output port is used, only one PD can be connected.
2. According to IEEE 802.3at/bt standard, the IPOE-E302
will not inject power to the cable if not connected to a
standard IEEE 802.3at/bt device.
3. DO NOT connect any non-standard PSE to PoE++
In port of the IPOE-E302; it may damage the device
permanently.
4. Power over Ethernet Budget
The following table lists how many PoE devices can be powered by the
IPOE-E302 over a distance of under 1m:
Power Source
PoE Output
Budget*
Max. Number of PDs supported
IEEE 802.3bt
PoE++ PSE (Type 4)
90 watts max.
Class 4 PD@25.5 watts 2 units
Class 3 PD@12.9 watts 2 units
Class 2 PD@6.5 watts 2 units
Class 1 PD@3.8 watts 2 units
IEEE 802.3bt
PoE++ PSE (Type 3)
60 watts max.
Class 4 PD@25.5 watts 1 unit
Class 3 PD@12.9 watts 2 units
Class 2 PD@6.5 watts 2 units
Class 1 PD@3.8 watts 2 units
IEEE 802.3at
PoE+ PSE (Type 2)
30 watts max.
Class 4 PD@25.5 watts 1 unit
Class 3 PD@12.9 watts 2 units
Class 2 PD@6.5 watts 2 units
Class 1 PD@3.8 watts 2 units
Remarks:
1. The PoE output budget means the aggregated power output of the 2
PSE ports.
2. The aggregated power consumption will be below 60 watts if with
PoE+ PSE.
Power over Ethernet Capability
With dierent distance and dierent PoE input source, it will inect the
PoE output capability. Please refer to the table below.
(A) (B)
PoE Output Capacity
(C)
(A): Distance
(B): Distance
(C): Watts
IPOE-E302
802.3bt PoE Switch (PSE)
When PoE Switch (PSE) Output is DC 52V.
A (Distance) B (Distance) C (Watts)
60M 2M 52.7W
60M 20M 50.1 W
60M 60M 49.6W
60M 100M 44.9W
100M 2M 39W
100M 20M 37.6W
100M 60M 36.5W
100M 100M 34.6W
When PoE Switch (PSE) Output is DC 54V.
A (Distance) B (Distance) C (Watts)
60M 2M 52.9W
60M 20M 50.8W
60M 60M 49.7W
60M 100M 44.9W
100M 2M 47.2W
100M 20M 45.9W
100M 60M 44.1W
100M 100M 42.2W
When PoE Switch (PSE) Output is DC 56V.
A (Distance) B (Distance) C (Watts)
60M 2M 54.1W
60M 20M 53.4W
60M 60M 52.1W
60M 100M 47.4W
100M 2M 51.8W
100M 20M 49.7W
100M 60M 48.2W
100M 100M 46.7W
Note
The table list shown here is for your reference only. The
actual performance should be related to your environment.
5.ProductSpecications
Model IPOE-E302
Hardware Specications
Network
Connector
PoE in Port
- 1 x 10/100/1000BASE-T Ethernet with 802.3bt
PoE++ “Data + DC” in
- Auto MDI/MDI-X, auto-negotiation RJ45 connector
PoE out Port
- 2 x 10/100/1000BASE-T Ethernet with IEEE
802.3at/bt PoE++ “Data + DC” out
- Auto MDI/MDI-X, auto-negotiation RJ45 connector
Switch
Architecture
Store-and-Forward switch architecture
MAC Address Table 2K MAC address table with auto learning function
Data Buer 1Mbit
Switch Fabric 6Gbps
Switch Throughput 4.46Mpps @ 64Bytes
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 9Kbytes
ESD Protection Air 8KV DC, Contact 6KV DC
Surge Protection 6KV
Enclosure IP67-rated and IK10 aluminum case
Installation Wall-mount ear
LED Display Link/ACT LED x 3
Dimensions
(W x D x H)
150 x 43.8 x 72.94 mm
169.85 x 43.8 x 72.94 mm, with cable gland
Weight 339g / 372g (with three waterproof cable glands)
Power
Consumption
97 watts/331.6BTU
(Full loading with PoE function)
Power over Ethernet
PoE Standard
PoE in Port
- IEEE 802.3bt PoE++ Type 4 standard PD
- PoH (Power over HDBASE-T)
- IEEE 802.3at PoE+ end-span/mid-span PD
Per PoE out Port
IEEE 802.3bt PoE++ end-span/mid-span PSE
PoE Power
PoE in Port 50~55V DC, max. 95 watts
Per PoE out Port 48~55V DC, max. 60 watts
Power Pin
Assignment
PoE in Port
1/2 (-), 3/6 (+), 4/5 (+), 7/8 (-) or 1/2 (+),
3/6 (-), 4/5 (+), 7/8 (-)
Per PoE out Port
1/2 (-), 3/6 (+), 4/5 (+), 7/8 (-) or 1/2 (+),
3/6 (-), 4/5 (+), 7/8 (-)
PoE Power Budget
65 watts (max.) @ IEEE 802.3bt PoE++ input
30 watts (max.) @ IEEE 802.3at PoE+ input
IEEE 802.3af PoE input not supported
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A
CE
Stability Testing
IEC 60068-2-32 (Free fall)
IEC 60068-2-27 (Shock)
IEC 60068-2-6 (Vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Environment
Operating
Temperature: -40 ~ 75 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage
Temperature: -40 ~ 85 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
6. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource and user’s manual on PLANET web site rst to check if it
could solve your issue. If you need more support information, please
contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.php?method=category&c1=2
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.